静电微电机微转子接触动力学特性分析

提出静电微电机中转子和固定轴承间相互接触的数学模型，对微尺度下的接触应力和应变 特性进行理论推导，分析静电微电机几何参数、静电力、材料特性及加载电压对接触宽度、 应力和应变特性的影响，对比研究不同工况下接触宽度、接触应力和应变的变化，并就相同 的问题进行有限元分析，探讨摩擦系数对接触区von Mises应力、应变和接触压力 的影响，结果表明有限元模拟所得接触应力和应变分布与数学 模型的解析值较为相似.     

非稳态载荷下轮轨滚动接触及其钢轨波磨研究

利用有限元法,考虑材料反复滚压条件下棘轮效应和局部滑动的影响,研究了非稳态机车和车辆车轮载荷作用下轮轨滚动接触的弹塑性应力、应变和变形,进而分析了塑性流动型钢轨波浪形磨损的形成和发展过程以及波谷和波峰处材料的力学行为.结果表明:在非稳态载荷作用下,钢轨接触表面产生不均匀塑性变形引起的波磨,波磨发展速率呈衰减趋势,最终趋于稳定状态;在相同载荷下,与车辆车轮相比,机车车轮对钢轨波磨影响较大;波谷处的残余应力、应变和变形大于波峰处.     

???????????????????о????

简述了多刚体系统接触及碰撞动力学的研究方法，详细回顾了考虑库仑摩擦的多刚 体系统的能量不协调、Painlev\'{e}疑难及碰撞恢复系数等该领域中难点问题的研 究进展，探讨了解决该难点问题的研究思路，指出了未来该领域的研究方向.     

压气机超速制造时弹塑性接触的数值模拟

“叶轮超速工艺“是叶轮制造中的一种重要方法.以某柴油机涡轮增压器的压气机为例,采用有限元参数二次规划法结合多重子结构技术分析模拟超速预加载制造时叶轮、轴套与轴之间接触应力的相应分布规律.针对不同的超速转速进行了大量计算,获得了超速转速与接触应力;超速转速与压气机内孔最大残余变形量;超速转速与轴套壁厚之间的关系.结果表明本文所采用的分析方法是可行的,弹塑性接触分析结果可作为叶轮设计及加工工艺的参考.     

特殊供油条件下点接触弹流润滑乏油分析

从实验中观测到的特殊乏油现象出发,提出1种特殊供油条件函数,求出点接触弹性流体动力润滑的完全数值解,定性模拟实验中的特殊乏油现象,并分析供油条件函数中的参数与中心膜厚和最小膜厚的关系.结果表明:供油油膜的两突起导致相应的压力、部分油膜比例和润滑油膜分布中也出现两突起;供油油膜的两突起能够扩大压力区和充分供油区域,能够局部改善润滑效果,但是对中心膜厚和最小膜厚影响很小;供油油量主要影响润滑状态,而供油油膜的形状在不同程度上也会影响润滑状态.     

Analysis of the plane contact with discontinuous curvature

The analytical solution for the plane contact between nonconforming C¹ profiles with a curvature discontinuity is obtained and discussed. The initial gap between the undeformed profiles was represented by a double parabolic function having the curvature discontinuity within the contact region. On the basis of the analytical solution, the complete analysis of pressure distribution was obtained. A raw technique to find an approximate solution is presented and comparison to the analytic one provided. For the limit case of strong curvature ratio the asymptotic treatment is discussed in terms of consistency with hypotheses claimed.     

Onset of Surface Damage in Modular Orthopedic Implants: Influence of Normal Contact Loading and Stress-assisted Dissolution

Surface damage at interfaces of modular implants results from repeated fretting contacts between metallic surfaces in a corrosive environment. As a first step in understanding this complex process, multi-asperity contact experiments were conducted to characterize roughness evolution due to action of contact loads and exposure to a reactive environment. Cobalt–chromium specimens with surface roughness similar to modular implant were first subjected to only contact loading and subsequently, to alternating contact loads and exposure to reactive environment. During repeated normal contact loading, amplitude of surface roughness reached a steady value after decreasing during the first few cycles. However during the second phase surface roughness amplitude continuously evolved—decreasing during contact loading and increasing on exposure to corrosive environment. The increase in roughness amplitude during surface reaction depended on the magnitude of applied contact loads. A damage mechanism that incorporates contact-induced residual stress development and stress-assisted dissolution is proposed to elucidate the measured surface roughness evolution.     

Synthesis of two A-B-C type conjugated amphiphilic triblock fullerene derivatives and their application in organic solar cells

Two A-B-C type conjugated amphiphilic triblock fullerene derivatives C60-2 HMTPB and C60-2 EHTPB were obtained in multi steps synthesis with three different blocks,and the amphiphilic diblock molecular C60-4 TPB was also preferred as a reference.When as modifying layer on zinc oxide(ZnO),the three fullerene derivatives can all reduce the work function of ZnO via modulation of the interfacial dipoles and lead a better electrical coupling.As introducing treatment of toluene,the obvious self-assembly of fullerene derivatives were observed,which were supported by X-ray diffraction and contact angle of water measurement.Base on PTB7-Th:PC71 BM system,the inverted organic solar cells devices with structure of ITO/ZnO/fullerene derivatives/PTB7-Th:PC71BM/Mo03/Al got power conversion efficiencies of 8.62%,8.83%and 9.00%for C60-4 TPB,C60-2 HMTPB and C60-2 EHTPB,respectively,compared 8.13%of devices with bare ZnO.The result of conjugated amphiphilic triblock fullerene derivatives provides a straightforward approaching by simultaneously modulating the morphology and interfacial work function of ZnO,which can also lead high performance in optoelectronic devices.     

Asymptotics of Neumann harmonics when a cavity is close to the exterior boundary of the domain

We construct the asymptotics (as ε→0) of solutions to the Neumann problem for the Laplace equation and of the corresponding Dirichlet integral. The problem concerns a three-dimensional domain having two connected components of the boundary at the distance ε>0. To cite this article: G. Cardone et al., C. R. Mecanique 335 (2007).