A new dodecylsulfate-selective supported liquid membrane electrode based on its N-cetylpyridinium ion-pair

A supported liquid and a poly(vinyl chloride) (PVC)-based membrane selective for dodecylsulfate (DS⁻) ion are described. The active element is a membrane containing a dissolved ion association complex of DS⁻ with cetylpyridinium (CP⁺) cation. The supported liquid membrane electrode (acetophenone as solvent) showed a Nernstian response towards the DS⁻ anion over the concentration range of sodium dodecylsulfate (SDS) from 8.3×10⁻³ to 1.0×10⁻⁶ mol dm⁻³ at 25 °C. The proposed electrode also showed a super-Nernstian potential response (108±2 mV decade⁻¹) at low concentrations (1.0×10⁻⁹ to 1.0×10⁻⁶ mol dm⁻³). Moreover, this electrode showed good selectivity and precision (R.S.D.?2.0%), and was usable within the pH range 4.0-6.8. The proposed electrode revealed a lower limit of detection of 6.3×10⁻⁷ mol dm⁻³ and improved selectivity in comparison with the some previously reported DS⁻ ion selective electrodes. The isothermal temperature coefficient of this electrode amounted to −0.001 V °C⁻¹. The liquid membrane electrode may find application in the direct determination of SDS by the standard addition method at pH 5.0, and in the physicochemical studies of surfactant solutions.     

Boiling Temperature and Reversed Deliquescence Relative Humidity Measurements for Mineral Assemblages in the NaCl + NaNO3 + KNO3 + Ca(NO3)2 + H2O System

Boiling temperature measurements have been made at ambient pressure for saturated ternary solutions of NaCl + KNO₃ + H₂O, NaNO₃ + KNO₃ + H₂O, and NaCl + Ca(NO₃)₂ + H₂O over the full composition range, along with those of the single salt systems. Boiling temperatures were also measured for the four component NaCl + NaNO₃ + KNO₃ + H₂O and five component NaCl + NaNO₃ + KNO₃ + Ca(NO₃)₂ + H₂O mixtures, where the solute mole fraction of Ca(NO₃)₂, x{Ca(NO₃)₂}, was varied between 0 and 0.25. The maximum boiling temperature found for the NaCl + KNO₃ + H₂O system is ≈134.9 ^∘C; for the NaNO₃ + KNO₃ + H₂O system is ≈165.1 ^∘C at x(NaNO₃) ≈ 0.46 and x(KNO₃) ≈ 0.54; and for the NaCl + Ca(NO₃)₂ + H₂O system is 164.7 ± 0.6 ^∘C at x{NaCl} ≈ 0.25 and x{Ca(NO₃)₂} ≈ 0.75. The NaCl + NaNO₃ + KNO₃ + Ca(NO₃)₂ + H₂O system forms molten salts below their maximum boiling temperatures and the temperatures corresponding to the cessation of boiling (dry-out temperatures) of these liquid mixtures were determined. These dry-out temperatures range from ≈300 ^∘C when x{Ca(NO₃)₂} = 0 to ≥ 400 ^∘C when x{Ca(NO₃)₂} = 0.20 and 0.25. Mutual deliquescence/efflorescence relative humidity (MDRH/MERH) measurements were also made for the NaNO₃ + KNO₃ and NaCl + NaNO₃ + KNO₃ salt mixture from 120 to 180 ^∘C at ambient pressure. The NaNO₃ + KNO₃ salt mixture has a MDRH of 26.4% at 120 ^∘C and 20.0% at 150 ^∘C. This salt mixture also absorbs water at 180 ^∘C, which is higher than expected from the boiling temperature experiments. The NaCl + NaNO₃ + KNO₃ salt mixture was found to have a MDRH of 25.9% at 120 ^∘C and 10.5% at 180 ^∘C. The investigated mixture compositions correspond to some of the major mineral assemblages that are predicted to control brine composition due to the deliquescence of salts formed in dust deposited on waste canisters in the proposed nuclear repository at Yucca Mountain, Nevada.     

Derivate von arsensubstituierten Phosphorchalkogeniden

Derivatives of Arsenic Substituted Phosphorus Chalcogenides α-AsP₃S₃I₂, α-AsP₃Se₃I₂, and three isomers of β-AsP₃S₃I₂ were observed besides several phosphorus sulfides by ³¹P NMR spectroscopy after the reaction of As_nP_4–nE₃ (E ? S; Se; n = 0–4) with I₂ in the melt or with I₂, PI₃, and N-iodosuccinimid in CS₂ solutions. The reaction of As_nP_4–nS₃ with CHI₃ in CS₂ solution yielded two isomers of β-AsP₃S₃(CHI₂)I.     

Mild and efficient Cs2CO3-promoted synthesis of phosphonates

A mild and convenient synthesis for phosphonates using cesium carbonate (Cs₂CO₃), tetrabutylammonium iodide (TBAI) and DMF was developed at room temperature. Numerous dialkyl phosphites were screened using a diverse array of alkyl halides and these reaction conditions were found to be highly efficient producing various phosphonates exclusively in moderate to high yields.     

Synthesis of 2,5-bis{(diethyl-3′-indolyl)methyl}furan and its N,N′-dimetallated complexes (lithium, sodium and potassium): X-ray crystal structures of 2,5-bis{(diethyl-3′-indolyl)methyl}furan and the polymeric tetrahydrofuran adduct of the dilithiated complex

The synthesis of 2,5-bis{(diethyl-3′-indolyl)methyl}furan by the acid catalysed condensation of 2,5-bis(diethylhydroxymethyl)furan with indole is presented. Dilithium, disodium and dipotassium derivatives are prepared by the reaction of the bis(indole) with n-BuLi, NaH and K, respectively, in the presence of various Lewis bases. The X-ray structures of 2,5-bis{(diethyl-3′-indolyl)methyl}furan and the dilithiated derivative (as a polymeric tetrahydrofuran adduct) are reported.     

Influence of plasticizers and crosslinking on the properties of biodegradable films made from sodium caseinate

Plasticized protein films were prepared by the casting method from water solution of sodium caseinate and plasticizers with the aim to obtain environmentally friendly materials for packaging applications. Mechanical properties (tensile strength, elongation and Young’s modulus) of caseinate based films were determined versus ratio of protein to plasticizer, plasticizer type and relative humidity conditions. Among the different polyol-type plasticizers tested, glycerol (Gly) and triethanolamine (TEA) were the most efficient for the improvement of mechanical properties (high strains for low stresses). Further, chemical crosslinking between formaldehyde (HCHO) and free amino groups (ε-NH₂) of sodium caseinate was performed to increase water resistance of TEA plasticized films. Optimal mechanical properties, i.e. elastic modulus of 105 MPa, tensile strength of 8-9 MPa for elongation at break about 110-125% were obtained for HCHO/ε-NH₂ ratios higher than 1.35. Protein specific water solubility was determined from a 280 nm absorbance. For convenient crosslinker (HCHO) content sodium caseinate solubility can be lowered to less than 5 wt% after 24 h immersion in water.     

Active transport of Na + and K + through animal cell membranes

The transport of Na⁺ out of the cell and K⁺ into the cell against a concentration gradient is catalyzed by a (Na⁺ + K⁺)-activated ATPase. The way in which the cations pass through the cell membrane has not yet been elucidated. Studies on the ATP hydrolysis revealed a Na⁺-dependent phosphorylation of the enzyme protein; the conformation of the enzyme also appears to change. The energy required for transport of the cations against their concentration gradients is probably provided by K⁺-dependent hydrolysis of the enzyme-bound phosphate. The enzyme can synthesize ATP from inorganic phosphate and ADP on reversal of the cation concentration gradient. By keeping the enzyme in a particular conformation, the cardiac glycoside ouabain specifically inhibits the Na⁺ pump.     

A Sensitive Spectrophotometric Determination of Nitrite in Water and Soil

A highly sensitive spectrophotometric method for the determination of nitrite in water and soil has been developed. The reaction of nitrite with acidified potassium iodide to liberate iodine which oxidizes leuco‐crystal violet (LCV) to form crystal violet having absorption maxima at 590 nm forms the bases of this method. In aqueous medium the system obeys Beer's law in the range of 0.1 to 1.0 μg per 25 mL (0.004–0.04 ppm), while in an extractive system the range is 0.025–0.25 μg in 100 mL (0.00025–0.0025 ppm). The molar absorptivity and Sandell's sensitivity were found to be 1.54 × 10⁶ 1 mol^?1 cm^?1 and 44 pg cm^?2, respectively.     

Surface properties of the binary mixed systems of alkylpyridinium halides and sodium alkylsulfonates

Surface properties of the binary mixed systems of decyl- and dodecylpyridinium chloride or bromide and sodium pentyl- and heptylsulfonate have been investigated. The surface tension of solutions of equimolar mixtures of surfactants and individual surfactants was measured, and the composition of mixed monolayers and surface interaction parameter β were calculated with the regular solution theory. Our results indicate that the properties of mixed films depend on both ionic strength and the kind of added inorganic electrolyte. With the increase of inorganic electrolyte concentration, the content of more surface active ions in the adsorption films enhances and is the highest in the presence of NaI and the smallest when solutions contain NaCl. Mutual interactions in mixed adsorbed films were found to be attractive. However, the strength of interaction weakens with the increase of ionic strength and depends on the kind of inorganic ions in the order: Cl⁻>Br⁻>I⁻.     

Sodium “stuffed” Ba2−xSrxFe4O8 ferrites: new cationic conductors

Sodium insertion in the tetrahedral layer structure of the ferrites Ba_2−xSr_xFe₄O₈ was performed by solid state reaction at 1220 K in air. Superstoichiometric oxides with the actual formula (Ba_2−xSr_x)_1−y/4Na_yFe₄O₈—y0.56; 0.60Ba/Sr1.67—were characterized by X-ray and neutron powder diffraction. The hexagonal unit-cell volume shows an increasing dependence on the sodium insertion when the Ba/Sr ratio reaches the largest values. The marked expansion of the c parameter is the likely signature of the location of the inserted sodium cations within the interlayer space. One-half of the sodium cations partly sits on the Sr(Ba) sites in octahedral coordination and the other half occupies extra octahedral and tetrahedral sites. ac conductivity measurements point to a cationic conductivity whose thermally activated regime—E_a 0.7 eV—evidenced from 570 K, is unsensitive to the sodium content. The bottleneck of the 2D sodium mobility regards the crossing of the oxygen triangular faces shared by the different polyhedra within the interlayer space.