Effect of Niobium Modifications to PZT (53/47) Thin Films Made by a Sol-Gel Route

Niobium-modified lead zirconate titanate thin films (PNZT) with nominal compositions, Pb_(1–0.5x) (Zr_0.53 Ti_0.47)_1–x Nb _x O₃:x = 0.02–0.07, have been prepared using a diol based sol-gel route. Single-layer (0.5 m) films were fabricated on platinised silicon substrates by spin-coating. The effect of niobium additions with regard to phase development, microstructure, and ferroelectric and dielectric properties were investigated for different annealing temperatures. For comparison, unmodified PZT films were also prepared. Niobium substitution increased the crystallisation temperatures for perovskite PNZT phase formation. The values of remanent polarisation P _r and dielectric constant _r were found to decrease with the introduction of Nb. For example, in films heated at 700°C for 15 min, the P _r value of an unmodified PZT film was 31 C cm^–2, compared to 17 C cm^–2 for an x = 0.05 PNZT film, whilst respective relative permittivity values fell from 1190 to 600. The highest Nb concentration film, x = 0.07, did not display any switchable polarisation characteristics, which is consistent with high levels of intermediate pyrochlore phase.     

Time-dependent mixing and demixing processes in binary lipid monolayers studied by mixed and separate spreading using film pressure and film potential measurements

Using both spreading techniques — mixed spreading and separate spreading- and, simultaneously, film pressure and film potential measurements, the mixing behavior of the following five binary systems was investigated and compared: 1) system 1,2-dilauroyl-phosphatidylethanolamine/cholesterol; 2) system 1,2-dimyristoyl-phosphatidylethanolamine/cholesterol; 3) system 1,2-dipalmitoyl-phosphatidylethanolamine/cholesterol; 4) system Na-eicosyl sulphate/hexadecanol; 5) system phosphatidic acid/1,2-dimyristoyl-phosphatidylethanolamine.Analyzing the time and concentration dependence of the /a isotherms and v/a isotherms (^s = film pressure, v ^s potential,a=average area per molecule in mixed films in the monolayers) of the binary monolayers it can be concluded that the components of the binary systems 1–4 are complete miscible in the monolayers. On the other hand the components of the system 5 are probably partially miscible only.     

STUDIES ON ENHANCED CONDUCTIVITY OF STRETCHED CONDUCTING POLYMERS

A physical model of series of the conductivity on chain and the interchain conductivitybetween chains is proposed to explain enhanced conductivity of stretched conducting polymers.This model suggests that the enhanced conductivity for stretched conducting polymers might bedue to increasing of the interchain conductivity between chains along the elongation direction afterdrawing processes if the conductivity on chain is assumed much larger than that of the interchainconductivity between chains. According to this model, it is expected that the temperaturedependence of conductivity measured by four-probe method for stretched conducting polymers iscontrolled by a variation of the interchain conductivity between chains with temperature, whichcan be used to explain that a metallic temperature dependence of conductivity for stretchedconducting polymers is not observed although the conductivity along the elongation direction isenhanced by two or three orders of magnitude.     

Performance characteristics of suspended particulate reagent-iminodiacetate as a binding agent for diffusive gradients in thin films

The performance characteristics of an alternative binding agent, suspended particulate reagent-iminodiacetate (SPR-IDA), for use with DGT methodology were investigated. The parameters investigated during this study included gel hydration, blank levels, elution factor (f_e), capacity, the effects of pH on the binding of trace metals by DGT. The novel application of this resin for use as a quantitative standard for laser ablation ICP-MS was also evaluated. To further constrain the results for the SPR-IDA binding agent, parallel experiments were performed using resin gel containing Chelex 100, which has been widely reported in the literature. Hydration results showed that the SPR-IDA resin gel reached a stable dimension and weight within ∼30 min and was dimensionally stable for ≤6 months. The measured DGT blanks for the SPR-IDA resin were 0.0023, 0.15, 0.21, 0.0033 and 0.011 ng disc⁻¹ for Co, Ni, Cu, Cd and Pb, respectively. The elution factor differed for the two resin types with the Chelex 100 recoveries slightly lower than previous reports and the SPR-IDA resin showing on average ∼5-9% better recoveries than DGT containing Chelex 100. The measured capacity of DGT discs containing the SPR-IDA binding agent was 0.26 mg Cd, similar to the calculated value of 0.29 mg Cd, indicating the entire resin layer was available for metal uptake.Both resin types performed equally well when deployed in 1 mM NaNO₃ solutions with DGT measurements of ∼100% of direct solution measurements for Co, Ni and Cd. However, DGT measurements of Cu and Pb systematically decreased with increasing solution pH down to ∼50% of solution values at pH 8.0, due to artifacts resulting from colloid formation during the addition of the metals. This was remedied by adding the metals as dilute salt standards and addition of Mg(NO₃)₂ to eliminate adsorption to the container walls. In the latter experiments, DGT measured concentrations of Co, Ni, Cu, Cd and Pb were in agreement with solution concentrations. Deployment of DGT in solutions with increasing concentrations of trace metals yielded linear results, suggesting that quantitative analysis using simplified laser ablation techniques should be possible using this newly characterized SPR-IDA resin gel.     

Chemical Solution Deposition of ZnO Thin Films by an Aqueous Solution Gel Precursor Route

An aqueous chemical solution deposition method was used to prepare thin films of ZnO on SiO₂/Si (1 1 1) substrates. Starting from an aqueous solution of Zn acetate, citric acid and ammonia, very thin films could be deposited by spin coating. Heating parameters, necessary for thin film annealing, were determined using FTIR experiments on dried gel precursors, heated up to different temperatures. The morphology and the thickness of the films were investigated by SEM. It is found that homogeneous thin films with grain sizes of about 20 nm are formed. XRD experiments show that there is an indication that the films, crystallized at 500°C, exhibit preferential grain growth along the c-axis.     

Surfactant in the gaseous phase II. Influence on stability of foams and thin liquid films

The influence of the vapors ofn-amyl orn-decyl alcohol on the stability of single thin liquid films, single bubbles, and foam columns was determined. It was found that the presence of surfactant vapors lowered the stability of foams and single foam films. The mechanism of the destabilizing action of the surfactant vapors on wet, dynamic foams under dynamic conditions is discussed. It is shown that the destabilizing action of the surfactant vapors is a further indication that surface elasticity forces are the main factor determining stability of wet, dynamic foams.     

Comparative study on the inclusion behaviour of cyclodextrin derivatives with venoruton and rutin by thin layer chromatography

The interaction of rutin and venoruton (troxerutin), with alpha-, beta- and gamma-cyclodextrin (CD), hydroxypropyl-beta-cyclodextrin (HP-beta-CD) and methyl-beta-cyclodextrin (M-beta-CD) was investigated by reversed-phase thin layer chromatography on polyamide plates. A mobile phase consisted of NH(4)OH; NH(4)Cl buffer solution containing various CD concentrations (pH = 9.7, 20 degrees C) was used as mobile phase. The equilibrium constants (K(f)) and the retention factor (R(f)) were determined and used to study the inclusion process. The in fluence of CDs on the solubility of rutin and venoruton was characterized by R(M) values and the increasing hydrophilicity of drugs. The results show that the inclusion capacity of cyclodextrins follows the order HP-beta-CD > M-beta-CD > beta-CD > gamma-CD, and rutin is more easily included by the studied cyclodextrins than venoruton. In addition, the thermodynamic parameters (Delta H, Delta S) for the formation of complexes were obtained from the van't Hoff equation, displaying the enthalpy-entropy compensation effect.     

Hydrogen-induced metal-oxide interaction studied on noble metal model catalysts

Summary The effect of hydrogen reduction on the structure and catalytic properties of “thin film”and “inverse”model systems for supported metal catalysts is discussed. Thin film model catalysts were obtained by epitaxial growth of Pt and Rh nanoparticles on NaCl(001), which were coated with amorphous or crystalline supports of alumina, silica, titania, ceria and vanadia. Structural and morphological changes upon hydrogen reduction between 473 and 973 K were examined by high resolution electron microscopy. Metal-oxide interaction sets in at a specific reduction temperature and is characterized by an initial “wetting”stage, followed by alloy formation at increasing temperature, in the order VO_x< TiO_x< SiO₂< CeO_x< Al₂O₃. “Inverse”model systems were prepared by deposition of oxides on a metal substrate, e.g. VO_x/Rh and VO_x/Pd. Reduction of inverse systems at elevated temperature induces subsurface alloy formation. In contrast to common bimetallic surfaces, the stable subsurface alloys of V/Rh and V/Pd have a purely noble metal-terminated surface, with V positioned in near-surface layers. The uniform composition of the metallic surface layer excludes catalytic ensemble effects in favor of ligand effects. Activity and selectivity, e.g. for CO and CO₂methanation and for partial oxidation of ethene, are mainly controlled by the temperature of annealing or reduction. Reduction above 573 K turned out to be beneficial for the catalytic activity of the subsurface alloys, but not for the corresponding thin film systems which tend to deactivate viaparticle encapsulation.</o:p>     

表面活性剂模板在空气-水界面ZrO2薄膜中的稳定性

采用模板——十二烷基苯磺酸(DBS-H)在空气-水界面组装ZrO₂薄膜，研究了DBS-H在ZrO₂自组装薄膜中的水溶性、化学稳定性、热稳定性和光化学稳定性。模板的各类稳定性将直接控制ZrO₂薄膜结构，主要表现在层间距变化上。从模板与Na₂SiO₃反应的研究中获得了一种制备ZrO₂ / SiO₂复合氧化物薄膜的新方法，并推测出该复合薄膜的结构。     

Molecular Tailoring of Surfaces: Pulsed Plasma Polymerization of Bromine Containing Monomers

The use of a variable duty cycle pulsed RF plasma is shown to provide film chemistry control during polymerization of saturated (CH₂Br₂) and unsaturated (CH₂=CHCH₂Br) bromine containing monomers. With both monomers, the degree of bromine atom retention in the films is observed to increase in a progressive fashion as the RF duty cycle employed during plasma polymerization is decreased. The film deposition rates, when expressed in terms of thickness per Joule of RF energy input, increase rapidly as the RF duty cycles are reduced. Additionally, the film morphology is observed to become increasingly smooth with decreasing RF duty cycles during deposition, as illustrated with the allyl bromide monomer. The film chemistry controllability of this study is demonstrated with monomers possessing the relatively weak C-Br bond. As such, the present work represents an important extension of the pulsed plasma polymerization approach to include retention of a labile bond during film formation. The introduction of reactive surface functional groups, at controlled densities, provides additional molecular tailoring possibilities via subsequent chemical derivatization processes.