Sol-Gel Processing of PbZrO3 Thin Films

PbZrO₃ (PZ) thin films have been prepared by 2-methoxyethanol route from lead oxide or lead acetate and zirconium n-butoxide. The use of lead oxide as lead source and the seeding layer of TiO₂ on Pt/TiO₂/SiO₂/Si substrate facilitate the formation of the perovskite phase.     

具有平整表面的定向纳米碳管膜的制备

为了获得表面平整的定向纳米碳管，通过化学及物理的方法将纳米碳管膜进行反转，使其原来的AAO模板底面成为新的表面，用溶液逐步去除表面的铝和氧化铝后，获得了平整的定向纳米碳管膜表面，从而可将其作为工作面使用. 还比较了5％NaOH和6%H₃PO₄＋1.8%H₂CrO₄溶液去除氧化铝的效果.     

Characterization of Carbon Film Electrodes for Electroanalysis by Electrochemical Impedance

The interfacial behavior of electrodes fabricated from carbon film resistors of 2 and 20 Ω in supporting electrolyte solutions of varying pH used in electroanalytical experiments has been characterized by electrochemical impedance spectroscopy with complementary cyclic voltammetric experiments. Equivalent circuits are proposed to fit the experimental data and the influence of electrode pretreatment has also been investigated.     

Pore size distributions in low‐k dielectric thin films from X‐ray porosimetry

X‐ray reflectivity has been used to determine the mass uptake of probe molecules in porous thin films supported on thick silicon wafers. The adsorption occurs by capillary condensation when the films are exposed to probe vapor at controlled partial vapor pressures. The probe solvent partial pressure was varied by mixing saturated air and dry air at constant temperature or by changing sample temperature at a constant vapor concentration. Pore size distribution in the films can be calculated from the probe uptake with typical porosimetric approaches such as the application of the Kelvin equation to convert partial pressure into pore size. For illustration, the pore size distribution of three different nanoporous thin films, the primary candidate of ultra‐low‐k interlevel dielectrics in the next generation of integrated circuit chips, was determined with this technique. These samples represent different generations of low‐k dielectrics developed by industry. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 2170–2177, 2002     

乙二胺铜－铁氰复合修饰电极薄膜的电沉积和结构表征及电化学性质

乙二胺铜－铁氰复合修饰电极薄膜的电沉积和结构表征及电化学性质陈昌国，李海梅，黄宗卿（重庆大学化工学院重庆６３００４４）关键词：铜、乙二胺，铁氰，修饰电极，光谱普鲁士兰（ＰＢ）修饰电极因其独特的电致变色现象而倍受关注。在１９７８年以来的十余年间里已相继...     

Influence of target surface degradation on the properties of r.f. magnetron‐sputtered calcium phosphate coatings

This paper reports a detailed study of how repeated r.f. magnetron sputtering from a hydroxyapatite (HA) powder target affects the nature and reproducibility of a sequential series of thin‐film coatings deposited onto Ti6Al4V substrates. An evaluation of the effective lifespan of the HA sputter targets and the reproducibility of the calcium phosphate (CaP) coatings produced from them has been made from Fourier transform infrared spectroscopy, XPS and, as appropriate, atomic force microscopy and SEM/energy dispersive x‐ray analyses. The annulus region of the target surface, from which sputtering under r.f. magnetron conditions normally occurs, showed severe surface degradation after only one deposition run, as indicated by significant PO₄^3? and OH^? depletion. This deterioration continued after each subsequent deposition cycle but to a much lesser extent than that observed in the initial sputtering period. The layers produced from all of the sputter runs contained the expected Ca²⁺ and PO₄^3? species characteristic of a CaP system but were OH^? deficient in the as‐deposited state. However, the chemical and morphological properties of the coatings did not change significantly until after the third consecutive sputter cycle. Hence, these data indicate that, even though a significant level of degradation of the HA target occurs at the outset of the sputtering procedure, the general plasma conditions employed here have a dominant influence on the coating properties until a critical degradation condition is met. As such, the compacted HA powder targets of interest can have a life‐cycle greater than single usage without detriment to the chemistry and morphology of the coatings produced from them. Copyright © 2003 John Wiley & Sons, Ltd.     

氧化钨薄膜微型电化学器件的研究

本文论述了WO_3薄膜氢离子敏器件的结构、原理、制备技术和测试分析。利用WO_3薄膜在H+溶液中由绝缘转化为导电特性,成功地研制成氢离子敏器件。这是一种简易而经济的微型pH敏器件技术。     

LiCoO_2 electrode/electrolyte interface of Li-ion batteries investigated by electrochemical impedance spectroscopy

The storage behavior and the first delithiation of LiCoO2 electrode in 1 mol/L LiPF6-EC:DMC:DEC elec- trolyte were investigated by electrochemical impedance spectroscopy (EIS). It has found that, along with the increase of storage time, the thickness of SEI film increases, and some organic carbonate lithium compounds are formed due to spontaneous reactions occurring between the LiCoO2 electrode and the electrolyte. When electrode potential is changed from 3.8 to 3.95 V, the reversible breakdown of the resistive SEI film occurs, which is attributed to the reversible dissolution of the SEI film component. With the increase of electrode potential, the thickness of SEI film increases rapidly above 4.2 V, due to overcharge reactions. The inductive loop observed in impedance spectra of the LiCoO2 electrode in Li/LiCoO2 cells is attributed to the formation of a Li1-xCoO2/LiCoO2 concentration cell. Moreover, it has been demonstrated that the lithium-ion insertion-deinsertion in LiCoO2 hosts can be well described by both Langmuir and Frumkin insertion isotherms, and the symmetry factor of charge transfer has been evaluated at 0.5.     

酞菁锰-表面活性剂薄膜电极的电化学表征及其对三氯乙酸的电化学催化作用的研究

将酞菁锰（ＭｎＰｃ）掺入阳离子表面活性剂双十二烷基二甲基溴化铵（ＤＤＡＢ）的氯仿溶液，并涂布于热解石墨电极表面，待氯仿挥发后即制得ＭｎＰｃ－ＤＤＡＢ薄膜电极。循环伏安实验表明，在ＫＢｒ溶液中，该薄膜电极有两对还原氧化峰，第一对峰的Ｅｐｃ１＝－０．２７Ｖ，Ｅｐａ１＝０．０１Ｖ；第二对峰的Ｅｐｃ２＝－０．７６Ｖ，Ｅｐａ２＝－０．６２Ｖ（ｖｓ．ＳＣＥ）。本文着重探讨了第二对峰的电化学行为，估计了该体系的电荷传递扩散系数Ｄｃｔ和表观非均相电极反应速率常数Ｋ０′等电化学参数，并可将该薄膜电极用于催化三氯乙酸的电化学还原。     

10,12—双炔廿三酸盐的LB膜特性研究

本文合成了10,12-双炔廿三酸,并用其在Si、SiO_2、CaF_2等基片上沉积了LB膜,结果表明,10,12-双炔廿三酸的镉盐成膜更稳定。这种LB膜在紫外光辐照下很快聚合,聚合前后的紫外-可见吸收光谱发生规律性的变化,并保持层状结构,等同周期稍变。通过红外吸收的二向色性分析,确定了该分子的取向。