尼龙－1010的聚集态结构

用ＷＡＸＤ、ＤＳＣ、方差－范围函数．密度测量等方法，研究了经不同热处理的尼龙－１０１０的聚集态结构．发现退火处理更有利于尼龙－１０１０结晶的生成和稳定，且尼龙－１０１０的结晶，有一个最佳的热处理温度．在该温度附近，尼龙－１０１０的结晶度和微晶尺寸里最大值．     

Use of short columns and high flow rates for rapid gradient reversed-phase chromatography

Summary Rapid analyses were performed using reversed-phase liquid chromatography with short (20–100 mm) columns swept by fast yet shallow gradients, and the results compared with those obtained with 150 mm columns and slow gradients. The resolution losses incurred with shorter columns were minimised by employing elevated flow rates, to ensure that comparable mean retention factors were experienced by individual analytes during gradients run on different columns. This conserves gradient steepness. High quality performance was obtained with turn-around times of 5–10 minutes. An overall 5-fold enhancement in the rate of information generation was obtained. The relevance of instrumental parameters and of column and packing dimensions, upon the potential for improved performance is discussed. Some implications for the rapidly developing technique of capillary electrochromatography are briefly indicated.     

Magnetische Messungen im Nahordnungsbereich vonHeusler-Phasen (Co,T)2 XY

Magnetic measurements onHeusler alloys (Co,T)₂ XY (field and temperature dependence) are performed around theCurie points (temperature range:T _C–50 toT _C+50). A method otherwise used to get rid of ferromagnetic impurities only ( _g versus 1/H plot) is applied to pure ferromagnets and yields completely new _g (extrap.) versusT curves with a maximumT _max> T _C. The method was applied to pure gadolinium first which has aCurie point within the accessible region of the susceptibility measuring device.

     

Metallocene ethylene-1-octene copolymers: Influence of comonomer content on thermo-mechanical, rheological, and thermo-oxidative behaviours before and after melt processing in an internal mixer

The influence of the comonomer content in a series of metallocene-based ethylene-1-octene copolymers (m-LLDPE) on thermo-mechanical, rheological, and thermo-oxidative behaviours during melt processing were examined using a range of characterisation techniques. The amount of branching was calculated from ¹³C NMR and studies using differential scanning calorimetry (DSC) and dynamic mechanical analysis (DMA) were employed to determine the effect of short chain branching (SCB, comonomer content) on thermal and mechanical characteristics of the polymer. The effect of melt processing at different temperatures on the thermo-oxidative behaviour of the polymers was investigated by examining the changes in rheological properties, using both melt flow and capillary rheometry, and the evolution of oxidation products during processing using infrared spectroscopy.The results show that the comonomer content and catalyst type greatly affect thermal, mechanical and oxidative behaviour of the polymers. For the metallocene polymer series, it was shown from both DSC and DMA that (i) crystallinity and melting temperatures decreased linearly with comonomer content, (ii) the intensity of the β-transition increased, and (iii) the position of the tan δ_max peak corresponding to the α-transition shifted to lower temperatures, with higher comonomer content. In contrast, a corresponding Ziegler polymer containing the same level of SCB as in one of the m-LLDPE polymers, showed different characteristics due to its more heterogeneous nature: higher elongational viscosity, and a double melting peak with broader intensity that occurred at higher temperature (from DSC endotherm) indicating a much broader short chain branch distribution.The thermo-oxidative behaviour of the polymers after melt processing was similarly influenced by the comonomer content. Rheological characteristics and changes in concentrations of carbonyl and the different unsaturated groups, particularly vinyl, vinylidene and trans-vinylene, during processing of m-LLDPE polymers, showed that polymers with lower levels of SCB gave rise to predominantly crosslinking reactions at all processing temperatures. By contrast, chain scission reactions at higher processing temperatures became more favoured in the higher comonomer-containing polymers. Compared to its metallocene analogue, the Ziegler polymer showed a much higher degree of crosslinking at all temperatures because of the high levels of vinyl unsaturation initially present.     

Faster GC analyses performed by flow programming in short capillary columns

The technique of programming the carrier gas flow rate in gas chromatography, especially in connection with the use of capillary columns shorter than 10 m can significantly accelerate GC analyses. Equations for calculation of the parameters of the exponential flow function and retention data are described. The effects of flow programming in a short capillary column are shown in a few chromatograms. Different programming rates are tested and compared with temperature programming.     

Study on microstructure and mechanical properties relationship of short fibers/rubber foam composites

Research on short fibers/rubber foam composites is rarely found in the literature. In this paper, microcellular rubber foams unfilled (MF), strengthened by pretreated short fibers (MFPS) and untreated short fibers (MFUS) are prepared, respectively. The microstructure and mechanical properties of the three composites have been studied via scanning electron microscope (SEM) and mechanical testing, respectively. The SEM results show that both pretreated and untreated short fibers disperse uniformly in the composites and in bidimensional orientation. Moreover, the pretreated short fibers have much better adhesion with the rubber matrix than untreated ones. The experimental results also indicate that the introduction of short fibers is mainly responsible for the great enhancement of most mechanical properties of the microcellular rubber foams, and the good interfacial adhesion of the short fibers with the matrix contributes to the more extensive improvement in the mechanical properties. It is also found that the reinforcement effect of short fibers to compressive modulus strongly depends on the density of microcellular rubber foams, the orientation of short fiber and the deformation ratio. The compressive modulus of microcellular rubber foams at the normalized density less than 0.70 and beyond 0.70 is predicted by the modified Simple Blending Model and the Halpin-Kerner Model, respectively. The theoretically predicted values are in good accordance with the experimental results.     

Haplotype studies support slippage as the mechanism of germline mutations in short tandem repeats

Germline mutations of human short tandem repeat (STR) loci are expansions or contractions of repeat arrays which are not well understood in terms of the mechanism(s) underlying such mutations. Although polymerase slippage is generally accepted as a mechanism capable to explain most features of such mutations, it is still possible that unequal crossing over plays some role in those events, as most studies in humans could not exclude unequal crossing over (UCO). Crossing over can be studied by analyzing haplotypes using flanking markers. To check for UCO in mutations, we have analyzed 150 paternity cases for which more than the usual trio (mother, child, and father) were available for testing by analyzing 16 STR loci. In a total of 4900 parent-child allele transfers four mutations were observed at different loci (D8S1179, D18S51, D21S11, and SE33/ACTBP2). To identify the mutated allele and to check for UCO, we typed at least four informative loci flanking the mutated locus and used the pedigree data to establish haplotypes. By doing so we were able to exclude UCO in each case. Moreover, we were able to identify the mutations as one-repeat contractions/expansions. Our data thus support slippage as the mechanism of germline mutations in STRs.     

Inside the Solvency 2 Black Box: Net Asset Values and Solvency Capital Requirements with a least-squares Monte-Carlo approach

The calculation of Net Asset Values and Solvency Capital Requirements in a Solvency 2 context–and the derivation of sensitivity analyses with respect to the main financial and actuarial risk drivers–is a complex procedure at the level of a real company, where it is illusory to be able to rely on closed-form formulas. The most general approach to performing these computations is that of nested simulations. However, this method is also hardly realistic because of its huge computation resources demand. The least-squares Monte Carlo method has recently been suggested as a way to overcome these difficulties. The present paper confirms that using this method is indeed relevant for Solvency 2 computations at the level of a company.     

Second Order Optimality Conditions for Problems with Continuously Differentiable Data

In this note, by making use of the concept of unbounded approximate Hessian matrices, we present second order optimality conditions for a constrained mathematical programming problem with data whose gradient map is continuous, but not necessarily locally Lipschitz.     

On Estimation of Temperature Uncertainty Using the Second Order Adjoint Problem

The uncertainty of temperature prediction from the heat flux error is estimated using first and second order adjoint equations. The adjoint codes developed for the inverse heat transfer problems provide the uncertainty estimation for the corresponding forward problems. Numerical tests corroborate the feasibility of fast uncertainty estimation using Hessian maximum eigenvalue obtained via second order adjoint equations.