Efficient separation of Cinnamomum camphora leaf essential oil and in vitro evaluation of its antifungal activity

Cinnamomum camphora leaf essential oil (CEO) was extracted using enzymatic-ultrasound pretreatment followed by microwave assisted extraction (EUP-MAE) method and simultaneously studied as a mycelial growth inhibitor against five important pathogens which cause potato dry rot. The optimum EUP-MAE conditions with a real CEO yield of 19.23 ± 0.12 mg/g were obtained through Plackett–Burman design and Box–Behnken design as follows: 3 % of enzyme dosage, 2 h of pretreatment time, 5 of pH, 210 W of ultrasound power, 50 °C pretreatment temperature, 16 mL/g of water to solid ratio, 30 min of microwave time and 500 W of microwave power. Compared to the reference methods, EUP-MAE possessed a highest CEO yield than these of ultrasound-microwave assisted extraction (U-MAE) and traditional hydrodistillation (HD). Gas chromatography-mass spectrometry (GC–MS) analysis demonstrated that eucalyptol, camphor, and α-terpineol were the three main constituents of CEO. Results from in vitro antifungal activity assay revealed that the mycelial growths of all the five tested Fusarium solani, Fusarium culmorum, Fusarium trichothecioides, Fusarium sporotrioides, and Fusarium avenaceum were apparently affected by CEO. These findings not only provide a potential paradigm for the separation of plant essential oil, but also guarantee a promising utilization of the CEO for potato protection to control the Fusarium spp.     

Lemon Oils Attenuate the Pathogenicity of Pseudomonas aeruginosa by Quorum Sensing Inhibition

The chemical composition of three Citrus limon oils: lemon essential oil (LEO), lemon terpenes (LT) and lemon essence (LE), and their influence in the virulence factors production and motility (swarming and swimming) of two Pseudomonas aeruginosa strains (ATCC 27853 and a multidrug-resistant HT5) were investigated. The main compound, limonene, was also tested in biological assays. Eighty-four compounds, accounting for a relative peak area of 99.23%, 98.58% and 99.64%, were identified by GC/MS. Limonene (59–60%), γ-terpinene (10–11%) and β-pinene (7–15%) were the main compounds. All lemon oils inhibited specific biofilm production and bacterial metabolic activities into biofilm in a dose-dependent manner (20–65%, in the range of 0.1–4 mg mL⁻¹) of both strains. Besides, all samples inhibited about 50% of the elastase activity at 0.1 mg mL⁻¹. Pyocyanin biosynthesis decreases until 64% (0.1–4 mg mL⁻¹) for both strains. Swarming motility of P. aeruginosa ATCC 27853 was completely inhibited by 2 mg mL⁻¹ of lemon oils. Furthermore, a decrease (29–55%, 0.1–4 mg mL⁻¹) in the synthesis of Quorum sensing (QS) signals was observed. The oils showed higher biological activities than limonene. Hence, their ability to control the biofilm of P. aeruginosa and reduce the production of virulence factors regulated by QS makes lemon oils good candidates to be applied as preservatives in the food processing industry.     

Application of magnetic solid phase extraction in separation and enrichment of glycoproteins and glycopeptides

The analysis of endogenous glycoproteins and glycopeptides in human body fluids is of great importance for screening and discovering disease biomarkers with clinical significance. However, the presence of interfering substances makes the direct quantitative detection of low-abundance glycoproteins and glycopeptides in human body fluids one of the great challenges in analytical chemistry. Magnetic solid phase extraction (MSPE) has the advantages of easy preparation, low cost and good magnetic responsiveness. Magnetic adsorbents are the core of MSPE technology, and magnetic adsorbents based on different functional materials are widely used in the quantitative analysis of glycoproteins and glycopeptides in human body fluids, making it possible to analyze glycoproteins and glycopeptides with low abundance as well as multiple types, which provides a technical platform for screening and evaluating glycoproteins and glycopeptides in body fluids as disease biomarkers. In this paper, we focus on the recent advances in the application of MSPE technology and magnetic adsorbents for the separation and enrichment of glycoproteins and glycopeptides in human body fluids, and the future trends and application prospects in this field are also presented.     

Sequential separation of Cu(II)/Ni(II)/Fe(II) from strong-acidic pickling wastewater with a two-stage process based on a bi-pyridine chelating resin

A self-synthesized bi-pyridine chelating resin (PAPY) could separate Cu(II)/Ni(II)/Fe(II) sequentially from strong-acidic pickling wastewater by a two-stage pH-adjusted process, in which Cu(II), Ni(II), and Fe(II) were successively preferred by PAPY. In the first stage (pH 1.0), the separation factor of Cu(II) over Ni(II) reached 61.43 in Cu(II)-Ni(II)-Fe(II) systems. In the second stage (pH 2.0), the separation factor of Ni(II) over Fe(II) reached 92.82 in Ni(II)-Fe(II) systems. Emphasis was placed on the selective separation of Cu(II) and Ni(II) in the first-stage. The adsorption amounts of Cu(II) onto PAPY were 1.2 mmol/g in the first stage, while those of Ni(II) and Fe(II) were lower than 0.3 mmol/g. Cu(II) adsorption was hardly affected by Ni(II) with the presence of dense Fe(II), but Cu(II) inhibited Ni(II) adsorption strongly. Part of preloaded Ni(II) could be replaced by Cu(II) based on the replacement effect. Compared with the absence of Fe(II), dense Fe(II) could obviously enhance the separation of Cu(II)-Ni(II). More than 95.0% of Cu(II) could be removed in the former 240 BV (BV for bed volume of the adsorbent) in the fixed-bed adsorption column process with the flow rate of 2.5 BV/h. As proved by X-ray photoelectron spectrometry (XPS) and density functional theory (DFT) analyses, Cu(II) exerted a much stronger deprotonation and chelation ability toward PAPY than Ni(II) and Fe(II). Thus, the work shows a great potential in the separation and purification of heavy metal resources from strong-acidic pickling wastewaters.     

icMRCI+Q理论研究CF离子12个-S态和23个?态的光谱性质

采用考虑Davidson修正的内收缩多参考组态相互作用(icMRCI+Q)方法结合相关一致基组aug-ccpV5Z和aug-cc-pV6Z计算了CF~+离子第一离解极限C~+(~2p_u)+F(~2P_u)对应的12个∧-S态(X~l∑~+,a~3∏,1~3∑~+,1~3Δ,1~1∑~-,1~1∑~-,1~3∑~-,2~1∑~+,1~1∏,2~3∏,2~1∏和2~3∑~+)所产生的23个Ω态的势能曲线.计算中考虑了旋轨耦合效应、核价相关和标量相对论修正以及将参考能和相关能分别外推至完全基组极限.基于得到的势能曲线,获得了束缚和准束缚的9个∧-S态和16个Ω态的光谱常数,并且X~1∑~+,a~3∏~(势阱一)∧-S态的光谱常数与已有的实验结果非常符合.此外,计算了CF自由基X~2∏态到CF~+离子束缚和准束缚的9个∧-S态的垂直电离势和绝热电离势,并且CF~+(X~1∑~+)←CF(X~2∏)和CF~+(a~3∏(势阱一))←CF(X~2∏)的垂直电离势和绝热电离势与相应的实验结果也非常符合.由a~3∏,1~1∏态和其他激发∧-S态势能曲线的交叉现象,借助于计算的旋轨耦合矩阵元,分析了a~3∏~(势阱一),1~1∏~(势阱一)和2~1∑~+态的预解离机理.计算的23个Ω态离解极限处的相对能量与实验结果十分吻合.最后计算了(2)0+~(势阱一)(v'=0-5),(1)1~(势阱一)(v'=0-5)和(2)1~(势阱一)(v'=0)到X0~+态跃迁的Franck-Condon因子和辐射寿命.     

硅单粒子位移损伤多尺度模拟研究

本文结合分子动力学方法和动力学蒙特卡罗方法, 研究了单个粒子入射硅引起的位移损伤缺陷的产生和演化过程; 基于Shockley-Read-Hall理论计算了单个粒子入射引起的位移损伤缺陷导致的泄漏电流增加及其演化过程, 比较了缺陷退火因子与泄漏电流退火因子之间的差异, 并将计算结果与实验值进行了对比. 结果表明, 计算泄漏电流时, 仅考虑一种缺陷的情况下缺陷退火因子与泄漏电流退火因子相同, 考虑两种缺陷类型情况下二者在数值上有所区别, 但缺陷退火因子仍能在一定程度上反映泄漏电流的退火行为. 分子动力学模拟中采用Stillinger-Weber势函数和Tersoff势函数时缺陷退火因子和泄漏电流退火因子与实验结果一致, 基于Stillinger-Weber势函数的计算结果与实验值更为接近.     

Single Chlamydomonas reinhardtii cell separation from bacterial cells and auto-fluorescence tracking with a nanosieve device

A planar, transparent, and adaptable nanosieve device is developed for efficient microalgae/bacteria separation. In the proposed method, a sacrificial layer is applied with dual photolithography patterning to achieve a 1D channel with a very low aspect ratio (1:10 000). A microalgae/bacteria mixture is then introduced into the deformable PDMS nanochannel. The hydrodynamic deformation of the nanochannel is regulated to allow the bacteria cells to pass through while leaving the microalgae cells trapped in the device. At a flow rate of 4 μL/min, the supernatant collected from the device is indistinguishable from a control solution, indicating that nearly all the microalgae cells are trapped in the device. Additionally, this device is capable of single cell auto-fluorescence tracking. These microalgae cells demonstrate minimal photobleaching over 250 s laser exposure and could be used to monitor hazardous compounds in the sample with a continuous flow. This method will be valuable to purify microalgae samples containing contaminations and study single-cell heterogeneity.     

Microalgae separation by inertia-enhanced pinched flow fractionation

To improve the accuracy and efficiency of ships’ ballast water detection, the separation of microalgae according to size is significant. In this article, a method to separate microalgae based on inertia-enhanced pinched flow fractionation (iPFF) was reported. The method utilized the inertial lift force induced by flow to separate microalgae according to size continuously. The experimental results show that, as the Reynolds number increases, the separation effect becomes better at first, but then stays unchanged. The best separation effect can be obtained when the Reynolds number is 12.3. In addition, with the increase of the flow rate ratio between sheath fluid and microalgae mixture, the separation effect becomes better and the best separation effect can be obtained when the flow rate ratio reaches 10. In this case, the recovery rate of Tetraselmis sp. is about 90%, and the purity is about 86%; the recovery rate of Chlorella sp. is as high as 99%, and the purity is about 99%. After that, the separation effect keeps getting better but very slowly. In general, this study provides a simple method for the separation of microalgae with different sizes, and lays a foundation for the accurate detection of microalgae in the ballast water.     

Inertial focusing of microparticles,bacteria, and blood in serpentine glass channels

Early detection of pathogenic microorganisms is pivotal to diagnosis and prevention of health and safety crises. Standard methods for pathogen detection often rely on lengthy culturing procedures, confirmed by biochemical assays, leading to >24 h for a diagnosis. The main challenge for pathogen detection is their low concentration within complex matrices. Detection of blood-borne pathogens via techniques such as PCR requires an initial positive blood culture and removal of inhibitory blood components, reducing its potential as a diagnostic tool. Among different label-free microfluidic techniques, inertial focusing on microscale channels holds great promise for automation, parallelization, and passive continuous separation of particles and cells. This work presents inertial microfluidic manipulation of small particles and cells (1–10 μm) in curved serpentine glass channels etched at different depths (deep and shallow designs) that can be exploited for (1) bacteria preconcentration from biological samples and (2) bacteria-blood cell separation. In our shallow device, the ability to focus Escherichia coli into the channel side streams with high recovery (89% at 2.2× preconcentration factor) could be applied for bacteria preconcentration in urine for diagnosis of urinary tract infections. Relying on differential equilibrium positions of red blood cells and E. coli inside the deep device, 97% red blood cells were depleted from 1:50 diluted blood with 54% E. coli recovered at a throughput of 0.7 mL/min. Parallelization of such devices could process relevant volumes of 7 mL whole blood in 10 min, allowing faster sample preparation for downstream molecular diagnostics of bacteria present in bloodstream.     

车辆高海拔环境起步性能试验研究

对于全域机动车辆而言,高海拔环境起步性能是评价其高原环境适应性和机动性的重要指标。针对多个型号车辆存在的高海拔环境起步困难问题,在系统开展车辆起步过程动力学分析的基础上,从车辆本身所具有的动力和所受外界阻力两个方面对高海拔环境车辆起步性能影响因素进行了深入分析,通过对某军用履带车辆高海拔起步性能的实车试验验证,确定了发动机低速扭矩特性、传动油温、行驶坡度、使用工况是高海拔环境影响车辆起步性能的关键因素,为车辆论证、研制、试验和使用工作的改进和发展提供了依据。