高反射膜激光零几率损伤阈值的实验研究

在确定光学薄膜激光损伤阈值的实验数据处理过程中,发现一些样品的数据点分布偏离直线型式。对此,用国际标准规定的零几率来确定损伤阈值的同时,对测试数据点采用了不同的非直线拟合,也得到一个零几率损伤阈值。比较两者差异,并与实验测试结果对照,发现这些样品采用非直线拟合得出的零几率损伤阈值与实际情况更接近一些。     

热处理条件对PVA薄膜阻氢性能的影响

采用XRD测定了PVA薄膜在不同热处理条件下的结晶度,并用自行设计的渗氢系数测量系统研究了在不同热处理条件下的PVA薄膜阻氢性能的变化规律。结果表明,PVA薄膜的热处理温度越高,其结晶度越高,越有利于提高PVA薄膜的阻氢性能,但热处理温度宜选择在180℃以下,以防止PVA薄膜热降解,另一方面,在PVA的玻璃化转变温度以下进行热处理同样能够提高PVA薄膜的阻氢性能,而醇解度较低的PVA薄膜在玻璃化转变温度以下经热处理后的阻氢性能提高的幅度较大。     

电子束、离子辅助和离子束溅射三种工艺对光学薄膜性能的影响

运用电子束、离子辅助和离子束溅射三种镀膜工艺分别制备光学薄膜,包括单层氧化物薄膜和增透膜,然后采取一系列测试手段,如Zygo轮廓仪、原子力显微镜、表面热透镜技术和X射线衍射等技术,来分析和研究不同的工艺对这些薄膜性能的不同影响,以判断合理的沉积工艺。     

Novel Protonic Conductive Silicates Produced by the Sol-Gel Method

ABSTRACT

Materials which display ionic conductivity were produced by the sol-gel and microemulsion-gel methods. The charging and discharging characteristics were investigated and it was found that a single ionic species was responsible for the conduction, the ionic species being residual protons from the initial component mixture. The complex impedence of various samples was measured and the ionic conductivities ranged in value from 9 × 10^?8 to 1 × 10^?5 ohm^?1 cm^?1. An Arrhemius plot for a microemulsion-gel revealed that the energy of activation was 0.15 eV.     

Effects of laser irradiation on optical properties of a-Se100−x Te x thin films

The effect of laser irradiation on the optical properties of thermally evaporated Se_100?x Te _x (x=8, 12, 16) chalcogenide thin films has been studied. The result shows that the irradiation causes a shift in the optical gap. The results have been analyzed on the basis of laser irradiation-induced defects in the film. The width of the tail of localized state in the band gap has been evaluated using the Urbach edge method. As the irradiation time increases, the values of the optical energy gap for all compositions decrease, while tail energy width increases. It is also observed that the optical energy gap decreases with increasing Te content in the alloy. These changes are a consequence of an increment in disorder produced by laser irradiation in the amorphous structure of thin film.     

Adhesive fracture of heterogeneous interfaces

We have studied the effect of interface heterogeneity on fracture, at both local and global scales. The single cantilever beam adhesion test was used to investigate interfacial fracture between polycarbonate plates and an elastic/fragile epoxy adhesive. Two surface treatments were applied to a (given) polycarbonate plate giving zones of strong and weak adhesion parallel to the crack direction. Calculated fracture energies differed from those expected from a simple rule-of-mixtures. A perturbation method, proposed by Rice, was used and results compared with crack fronts observed in situ. The technique was applied successfully but the difference in values of stress intensity factor between the zones was found substantially different from the experimental value. In an attempt to explain discrepancies, specimens with discontinuous crack fronts (adhesive and/or plates severed along the strong/weak adhesion frontier) were tested. Good agreement was found with the rule-of-mixtures predictions raising questions about the role of crack front continuity in load transfer.     

Characterizing polymer macrostructures by identifying and locating microstructures along their chains with the kerr effect

In this brief report, we demonstrate that Kerr effect measurements, which determine the excess birefringence contributed by polymer solutes in dilute solutions observed under a strong electric field, are highly sensitive to and capable of determining their microstructures, as well as their locations along the macromolecular backbone. Specifically, using atactic triblock copolymers with the same overall composition of styrene (S) and p-bromostyrene (pBrS) units, but with two different block arrangements, that is, pBrS₉₀-b-S₁₂₀-b-pBrS₉₀ (I) and S₆₀-b-pBrS₁₈₀-b-S₆₀ (II), which are indistinguishable by NMR, we detected a dramatic difference in their molar Kerr constants (_mK), in agreement with those previously estimated. Although similar in magnitude, their Kerr constants differ in sign, with _mK(II) positive and _mK(I) negative. In addition, S/pBrS random and gradient copolymers synthesized by reversible addition-fragmentation chain-transfer (RAFT) polymerization exhibit a heretofore unexpected enhanced enchainment of racemic (r) pBrS-pBrS diads. Comparison of their observed and calculated _mKs suggests that the gradient S/pBrS copolymers possess an unanticipated additional gradient in stereosequence that parallels their comonomer gradient, that is, as the concentration of pBrs units decreases from one end of the copolymer chain to the other, so does the content of r diads. This conclusion could only be reached by comparison of observed and calculated Kerr effects, which access the global properties of macromolecules, and not NMR, which is only sensitive to local polymer structural environments, but not to their locations on the copolymer chains. Molar Kerr constants are characteristic of entire polymer chains and are highly sensitive to their constituent microstructures and their distribution along the chain. They may be used to both identify constituent microstructures and locate them along the polymer chain, thereby enabling, for the first time, characterization of their complete macrostructures. © 2013 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2013     

Influence of the e-beam irradiation and photo-oxidation aging on the structure and properties of LDPE-OMMT nanocomposite films

In this paper two systems, polyethylene (LDPE) and polyethylene/commercial organo-modified montmorillonite (LDPE/OMMT) nanocomposite, were subjected to e-beam irradiation at different doses and both the molecular modifications and mechanical properties have been investigated through solubility, FT-IR, calorimetric and tensile tests. Moreover, in some of the irradiated systems photo-oxidation aging was performed and its effects were studied. The results show an enhancement with irradiation of the positive effect of the nano-filler loading, related to the increase of the mechanical properties, due to the increase of the nano-filler polymer interaction.Nevertheless calorimetric and FT-IR data indicate that the well known reduction of LDPE/OMMT nanocomposite resistance to photo-oxidation ageing, with respect to LDPE, is amplified by ionizing radiation.     

低温生长Cu(InGa)Se2薄膜吸收层的掺钠工艺研究

在柔性聚酰亚胺衬底上低温制备Cu(In,Ga)Se₂薄膜太阳能电池, Na的掺入会改善电池特性, 但不同的掺Na工艺对Cu(In,Ga)Se₂薄膜和器件特性的改善机理不同. 本实验通过对比前掺NaF和后掺NaF工艺发现, 在前掺Na工艺下, 由于Na始终存在于Cu(In,Ga)Se₂薄膜生长过程中, Na存在于多晶 Cu(In,Ga)Se₂ 薄膜晶界处, 起到了扩散势垒的作用, 导致晶粒细碎、加剧两相分离, 同时减小了施主缺陷的形成概率; 而在后掺Na工艺下, 掺入的Na对薄膜的结构及生长不产生影响, 仅仅起到了钝化施主缺陷、改善薄膜缺陷态的作用. 同时, 研究表明, 后掺Na工艺中, NaF必须依靠外界能量辅助才能扩散进Cu(In,Ga)Se₂内部, 实验结果证实, 只有衬底温度达到350 ℃以上时, 掺入的NaF才能较好地改善薄膜特性. 最终经掺Na工艺的优化, 得到低温工艺制备的柔性聚酰亚胺衬底器件效率达10.4%.