ZnO-coated glass fibers for the analysis of trihalomethanes by headspace-solid phase microextraction-gas chromatography

Li₂O-ZrO₂-BaO-SiO₂ glass fibers were produced and their surfaces were coated with zinc oxide. The fibers’ surface morphology was examined by scanning electron microscopy and the zinc oxide layer was characterized by mapping the K_α and L_α lines of zinc by energy dispersive X-ray spectroscopy. The results indicated that a homogeneous and porous layer of ZnO was formed on the fibers’ surface. This layer was subjected to a simultaneous determination of trihalomethanes using headspace-solid phase microextraction-gas chromatography. The study was conducted after evaluating the ideal time of incubation (15 min), extraction (15 min) and desorption (10 min), as well as the effect of the addition of salt (15%, m/v) on the analytical response. A good linear dynamic range was observed individually for trihalomethanes aqueous solutions containing 20 μg L⁻¹ and 500 μg L⁻¹ of trichloromethane, 15 μg L⁻¹ and 250 μg L⁻¹ of dichlorobromomethane and dibromochloromethane and 10 μg L⁻¹ and 100 μg L⁻¹ of tribromomethane, with all the compounds showing correlation coefficients higher than 0.9900.     

Low-energy electrons and X-ray irradiation effects on plasma-polymerized allylamine bioactive coatings for stents

Radiation used in biomedical applications causes chemical changes to biomedical materials. This work is an ex situ simulation of the influence of low-energy electron (LEE) impact and X-ray irradiation on the chemical properties of plasma-polymerized allylamine (PPA) bioactive and biocompatible stent coatings. Preliminary X-ray photoelectron spectroscopy (XPS) results show that PPA coatings oxidize in contact with ambient air by the detection of C-O and CO bonds which are typical of polymer oxidation. Chemical changes after LEE and X-ray irradiation are mainly a loss of oxygen, assuming a surface deoxidizing and not a complete destruction of the surface. XPS survey analyses show that the amine groups remain stable during irradiation. LEE impact measurements by TOF mass spectrometry show that the main ionic losses are H⁻ ions. It appears that CN groups are stable under irradiation and we observe a loss of hydrogen and oxygen as the main chemical modifications. In conclusion, these results suggest that PPA coatings are stable under biomedical radiation, and they can therefore be used for bioactive and biocompatible stent coatings.     

Crack‐free sol‐gel coatings for protection of AA1050 aluminium alloy

Organically modified sol‐gel coatings have been investigated as potential replacements for chromate conversion treatments of an AA1050 aluminium alloy. The coatings were prepared by combination of a completely hydrolysable precursor of tetra‐n‐propoxyzirconium (TPOZ), with a partially hydrolysable precursor of glycidoxypropyltrimethoxysilane (GPTMS). GPTMS contains an organic functional group, which is retained in the sol‐gel coatings after the hydrolysis–condensation process. Different GPTMS/TPOZ ratios and withdrawal speeds were studied. Coatings produced using a low GPTMS/TPOZ ratio and a high withdrawal speed generated significant cracks due to the shrinkage of the coatings, with no corrosion protection of the alloy. It was found that increase of organic moieties reduced the shrinkage of the coatings and the tendency for crack formation. By control of process parameters and ratios of organic and inorganic moieties, crack‐free sol‐gel coatings above 1 µm thick, with improved corrosion protection, can be produced on the alloy surface. Copyright © 2010 John Wiley & Sons, Ltd.     

Selectivity and efficiency of different reversed-phase and mixed-mode sorbents to preconcentrate and isolate aroma molecules

A comparison of the ability of different sorbent systems, including mixed-mode resins and reversed-phase sorbents, to extract and isolate volatile molecules from hydroalcoholic medium has been carried out by means of the determination of liquid–solid distribution coefficients. Eighteen volatile compounds covering a wide range of physicochemical properties (acids, bases and neutrals) and chemical functionalities, and thirteen different sorbents have been tested. LiChrolut EN and Isolute ENV (both polymeric with high surface area) showed the highest retention capability for nearly all analytes at all pHs tested. Exceptions were 2,3,5-trimethylpyrazine, most efficiently extracted with Strata XC at acidic pH, and indole best retained with Oasis MCX and Strata XC at any pH. Although nearly all basic compounds were most selectively extracted with cationic mixed-mode resins at acid pHs and 3-mercaptohexyl acetate and m-cresol show maxima α at pH 10 with Oasis MAX, the α values obtained have been relatively low, which suggests that retention is not particularly driven by ionic forces. The study has also shown that selectivity depends on the pH, the exact kind of mixed-mode sorbent and on the polarity of the analyte. High selectivity towards ionogenic compounds can be obtained by combining retention in mixed mode, a rinsing with a non-polar solvent and further elution with a solvent containing a neutralizing agent. However, not all the ionogenic molecules seem to be retained in ionic mode in the conditions tested and the complete elution of some analytes can be difficult, which suggests that analyte-specific isolation procedures should be analyzed case by case.     

超临界二氧化碳中无水相涂料的合成与表征

为了减小传统纸张涂布中涂料水分对涂布能耗、涂布质量以及对涂布原纸质量的影响,研究了以超临界二氧化碳为反应介质,制备聚甲基丙烯酸甲酯(PMMA)和碳酸钙颜料混合的粉末涂料粒子.通过FTIR、GPC-十八角度激光光散射联用技术对PMMA组成结构进行了表征,考察了反应体系中引发剂浓度、单体浓度、稳定剂浓度、反应温度和反应时间对聚合反应的转化率和聚合产物的分子量的影响.实验表明,当反应条件为反应压力10MPa,反应温度75℃,反应时间8h,单体浓度0.10g/mL,引发剂浓度0.10×10-2g/mL,稳定剂浓度0.06×10-2g/mL时,其聚合反应的转化率较高,同时PMMA的分子量适中,分子量分布窄.SEM观察到混合涂料粒子颗粒均匀,表明颜料在粉末涂料体系中分散性良好.     

温敏聚氨酯膜用于不同尺寸物质的选择性分离

通过湿法转相技术制备了温敏聚氨酯(thermal sensitive polyurethane,TSPU)膜,并用于氯化钠、甘氨酸和胶原蛋白等不同尺寸物质的选择性分离.示差扫描量热分析仪(DSC)和X射线衍射(XRD)分析表明,TSPU具有典型的嵌段结构(即软段和硬段),软段和硬段具有各自的结晶相及相态转变温度(将软段的相转变温度定义为开关温度,Ts).热台偏光显微镜观察表明,当温度低于Ts时,TSPU的软段具有较好的结晶形态,且为球晶型;但当温度超过Ts后,软段的结晶逐渐熔融、消失.运用扫描电镜(SEM)和原子力显微镜(AFM)对TSPU膜的形貌结构进行分析,结果表明,TSPU膜的表面(层)相对致密,且具有细小的微孔结构;截面为非对称的多孔结构,这种形态结构对TSPU膜的选择渗透性起决定性作用.通过测定湿膜干燥后的质量损失来计算膜的孔隙率发现,当温度从Ts-10℃升高到Ts+10℃时,膜的孔隙率从46.7%上升到65.3%,表现出明显的温敏特性.将TSPU膜用于氯化钠、甘氨酸和胶原蛋白分离时发现,尺寸较小的物质如钠离子和氯离子在低温下即可透过,且透过通量随温度的升高而增大.而中等尺寸甘氨酸的透过通量则呈现明显的温度依赖性,即低温时(TTs),由于存在栅栏效应,透过通量较小;高温时(TTs),甘氨酸的透过通量明显增大,显示出了温敏特性.胶原蛋白由于分子尺寸大,即使在开关温度以上,也不能透过TSPU膜.因此,利用TSPU膜的温敏特性,可以实现胶原蛋白、氨基酸、氯化钠等不同尺寸物质的选择性分离.     

Dual‐column capillary microextraction (CME) combined with electrothermal vaporization inductively coupled plasma mass spectrometry (ETV‐ICP‐MS) for the speciation of arsenic in human hair extracts

In this work, dual‐column capillary microextraction (CME) system consisting of N‐(2‐aminoethyl)‐3‐aminopropyltrimethoxysilane (AAPTS)‐silica coated capillary (C1) and 3‐mercaptopropyl trimethoxysilane (MPTS)‐silica coated capillary (C2) was developed for sequential separation/preconcentration of arsenite [As(III)], arsenate [As(V)], monomethylarsonic acid [MMA(V)] and dimethylarsinic acid [DMA(V)] in the extracts of human hair followed by electrothermal vaporization inductively coupled plasma mass spectrometry (ETV‐ICP‐MS) detection with iridium as permanent modifier. Various experimental parameters affecting the dual‐column microextraction of different As species had been investigated in detail. It was found that at pH 9, As(V) and MMA could be quantitatively retained by C1 and only As(III) could be quantitatively retained by C2. With the aid of valve switching, As(V)/MMA(V) retained on C1 and As(III) retained on C2 could be sequentially desorbed by 10 µl of 0.01 mol l^?1 HNO₃ [for As(V)], 0.1 mol l^?1 HNO₃ [for MMA(V)] and 0.2 mol l^?1 HNO₃‐3% thiourea (m/v) [for As(III)], respectively, the eluents were immediately introduced into the Ir‐coated graphite tubes for further ETV‐ICP‐MS detection. With two‐step ETV pyrolysis program, Cl^? in the sample matrix could be in situ removed, and the total As in the human hair extracts or digested solution could be interference‐free, determined by ETV‐ICP‐MS. DMA(V) in the human hair extracts was obtained by subtraction of total As in the human hair extracts from other three As species. Under the optimized conditions, the detection limits (3 σ) of the method were 3.9 pg ml^?1 for As(III), 2.7 pg ml^?1 for As(V), 2.6 pg ml^?1 for MMA(V) and 124 pg ml^?1 for total As with the relative standard deviations less than 7.0% (C = 0.1 ng ml^?1, n = 7), and the enrichment factor was 286, 262 and 260 for As(III), As(V) and MMA(V), respectively. The developed method was successfully applied for the speciation of arsenic in the extracts of human hair. Copyright © 2009 John Wiley & Sons, Ltd.     

Bi基化合物膜包覆ZnO的制备和电化学性能

为提高锌镍电池ZnO的循环充放电性能,采用Bi(NO3)3水解沉积法对ZnO包覆Bi基化合物膜,系统研究了包覆ZnO的微结构和电化学性能。TEM,XRD和EDS表明由Bi6(NO3)4(OH)2O6·2H2O,BiO和Bi2O3组成的Bi基化合物膜包覆在ZnO表面。表面包覆能提高ZnO的循环性能和放电容量,含5.1wt%Bi的包覆ZnO循环性能稳定,平均放电容量为509mAh·g-1,利用率为78%,性能有较大改善。充放电曲线和循环伏安结果均表明包覆Bi基化合物膜能降低锌镍电池的充电平台,加宽放电平台,提高ZnO的电化学活性。包覆Bi基化合物膜能有效减小活性材料与碱性电解液的接触,抑制ZnO的溶解,提高循环稳定性;而包覆膜的微孔结构又可使活性材料接触到电化学反应必须的H2O和OH-,保证了高的放电容量。     

Synthesis of Mesoporous Cu-Mn-Al_2O_3 Materials and Their Applications to Preferential Catalytic Oxidation of CO in a Hydrogen-rich Stream

A series of mesoporous Cu-Mn-Al2O3(CMA) materials was synthesized at moderate temperature and their structures were characterized by XRD, N2 physical adsorption and TPR techniques. It was found that using metal complex ion[Cu(NH3) 42+-Mn(NH3)62+] as raw materials is easier to form good-structure mesoporous Cu-Mn-Al2O3 materials than using its nitrate salt [Cu(NO3)2-Mn(NO3)2]. The TPR tests results indicate that CuO and MnOx were homogeneously dispersed in the mesoporous materials. Their catalytic application to preferential catalytic oxidation of CO in a hydrogen-rich stream was studied. The activity varies in the order of CMA(1:1, molar ratio) CMA(1:2)CMA(2:1)CMA(CP)CMA(1:0)≈CMA(0:1). The CMA(1:0) and CMA(0:1) have lower activity compared to other samples, implying that there existed coordination effect between Cu-Mn in the samples. The selectivity varied in the order of CMA(0:1)≥CMA(1:2)CMA(1:1)CMA(2:1)CMA(1:0) at higher temperature (≥120 °C), indicating that increasing the Cu content enhanced the conversion of H2. The sample CMA(CP) made by coprecipitation method has a lower CO oxidation activity and selectivity than its counter-parts of mesoporous Cu-Mn-Al2O3 materials[CMA(1:2)], this attributed to the lower surface area of the former and poor interaction of CuO with MnOx.