不同灰化温度下生物质混煤灰的烧结特性研究

选取晋城无烟煤和麦秆作为研究对象,利用压差法烧结温度测定装置测量不同灰化温度下煤和麦秆混合灰的烧结温度,再利用SEM-EDS以及XRD对灰样进行烧结特性分析。结果表明,不论灰化温度高低,随着麦秆的添加,煤和麦秆混合灰的烧结温度都呈现降低趋势,其降低幅度略有差别。灰化温度较低时,煤和麦秆混合灰的烧结温度低于灰化温度较高情况下混合灰的烧结温度。SEM-EDS分析表明,低温灰化得到的样品中出现较多不规则的纤维结构;较高温度下获得的灰样中出现较多致密的球状颗粒,这表明矿物质发生熔融形成球状颗粒。XRD分析表明,低温灰化烧结后的煤和麦秆混合灰样中因含有较多的含钾等碱金属系助融矿物质,导致混合灰样的烧结温度降低。然而,像钙长石等含钙矿物质本身具有较高的熔点,因此,在1 100℃时混合灰样具有较高的烧结温度。     

烧结温度和升温速率对Pb(Sb1/3Mn2/3)0.05Zr0.47Ti0.48O3压电陶瓷性能的影响

采用传统固相法制备了Pb(Sb1/3 Mn2/3)0.05Zr0.47Ti0.48 O3 (PMS-PZT)压电陶瓷.利用XRD、SEM和EDS等研究PMS-PZT陶瓷体系在烧结过程中形成的过渡液相和形成过渡液相温度(1100℃)附近的升温速率对陶瓷结构、压电和介电性能的影响.结果表明:不同烧结温度下,所有样品均为单一的钙钛矿四方相,过渡液相不会对相的结构有影响,但是当烧结温度较低时,过渡液相在烧结后期以玻璃相在晶界附近富集,对陶瓷的压电和介电性能有很大影响.随着烧结温度和升温速率的升高,PMS-PZT晶粒尺寸增大,晶粒均匀性和规则性得以改善,晶化质量得到提高;d33测试和阻抗分析测试结果表明PMS-PZT样品在1100℃附近以7 ℃·min-1升温速率并在1250℃烧结时具有最好的压电和介电性能:d33 =313 C/N,kp=0.59,Qm=1481,εr=1437,tanδ=0.53;.     

(Gd,Lu)3Al5O12∶Tb3+,Eu3+透明陶瓷制备与发光性能

通过简单的化学沉淀法制备了纳米前驱体,结合真空烧结工艺,制备了一系列镥稳定钆铝石榴石{(Gd, Lu)₃Al₅O₁₂∶Tb,Eu}透明陶瓷。将透明陶瓷加工成1 mm厚的圆片,对透明陶瓷样品进行了X射线衍射、光致发光、透过率和衰减时间等表征。高温烧结过后,陶瓷样品仍保持稳定的石榴石相。选定313 nm作为透明陶瓷的激发波长,可获得最强的荧光发射。此外,通过对不同样品进行紫外可见荧光测试,获得了由绿光到红光的可调节发射。在313 nm激发,543 nm和591 nm的监测波长下,透明陶瓷样品均具有Eu³⁺的毫秒级衰减时间。     

The Measurement of the Dispersion of Pd/C Catalysts

A 10 w/o Pd/C catalyst from Johnson Matthey has been examined by three different techniques: chemisorption, line broadening of X-ray diffraction, and TEM (transmission electron microscopy) to investigate the size of the palladium crystallites. The dispersion of this catalyst was determined to be 20%. Among these techniques, the X-ray diffraction was found to be the most convenient method. Through this method, the dispersion of Pd was found to decrease on catalyzing hydroxylamine reactions at 330 K. The deactivation of Pd/C for these reactions was correlated to the sintering of palladium. H₂ chemisorption at 373 K was found to be a good way to accurately measure the number of active palladium sites in the Pd/C catalysts.     

Microstructural prototyping of ceramics by kinetic engineering: applications of spark plasma sintering

The significance of kinetics on the development of microstructures in connection with sintering of ceramics is well recognized. In practice, however, it still remains a challenge to prepare designed microstructures via engineering the sintering kinetics because of an insufficient understanding of the different operative mechanisms that are in many cases overlapping. In this article the kinetic issues involved in sintering are described and discussed with respect to their potential for prototyping microstructures that yield desired properties. By exploiting and mastering the differences present in the kinetics of grain sliding, densification, chemical reactions, and grain growth, respectively, we have established processing principles for producing bulk ceramics with microstructures consisting of nano-sized grains, aligned grains, and/or non-equilibrium-phase constitutions, and for achieving radically improved superplasticity in brittle ceramics. Although the studies quoted in this article were mainly carried out by spark plasma sintering, more general implications of them are expected, including efficient particle sliding, deformation-induced dynamic ripening, superplastic deformation-induced dynamic ripening, and non-equilibrium integration.     

高压烧结法合成致密纳米BaTiO3陶瓷结构和铁电性能研究

 在6 GPa压力、1 000 ℃温度条件下制备了致密的纳米BaTiO₃陶瓷，合成样品的平均晶粒尺寸为50 nm，理论密度在97%以上。通过介电测量，观察到了样品宽化的相变峰，它与粗晶陶瓷的相变峰大不相同。由于90°电畴的减少和退极化场的存在，观察到了细长的电滞回线，它是样品铁电性存在的有力证据，表明钛酸钡陶瓷的临界尺寸在50 nm以下。     

Effects of process parameters on electrical properties of n-type Bi2Te3 prepared by mechanical alloying and spark plasma sintering

n-Type Bi₂Te₃ thermoelectric materials were prepared by spark plasma sintering (SPS) using mechanically alloyed powders. Seebeck coefficient and electrical conductivity of the resultant materials were measured, with emphasis on the effects of sintering process parameters on the electrical properties. The power factor was improved from 1.5 to 1.6 mW/mK² when the SPS pressure was increased from 20 to 50 MPa at 623 K, and was further increased to 2.1 mW/mK² under 50 MPa by raising the SPS temperature from 623 to 673 K. The maximum power factor was obtained for the sample sintered under optimized SPS process parameters, in which the sintering temperature and the sintering pressure are 673 K and 50 MPa, respectively.     

Sinter-active nanocrystalline CeO<Subscript>2</Subscript> powder prepared by a mixed fuel process: Effect of fuel on particle agglomeration

A modified combustion process, namely a mixed fuel process making use of a mixture of two fuels, such as citric acid and glycine has been developed to prepare nanocrystalline ceria powders. The effect of the mixed fuel and the different fuel to oxidant ratios on the decomposition characteristics of the gels were investigated by simultaneous thermal analysis experiments. It was established from various characterization techniques that the ceria powder prepared through the mixed fuel process has got the optimum powder characteristics, namely, a surface area of 33.33 m²/g and a crystallite size of 14 nm compared to the powders produced through the combustion process using a single fuel like glycine or citric acid. Such powders when sintered at 1250°C resulted in pellets with densities in the range of 94–96% of theoretical density. In this paper, we have carried out systematic studies on the sintering of ceria powders prepared by different approaches. The sintered ceramic from mixed fuel batch, exhibited and retained relative density more than 95% up to 1250°C and this data clearly underscores the ability of this process in developing ceria ceramics with increased stability against reduction.     

[5‐(p‐alkoxy)phenyl‐10, 15, 20‐tri‐phenyl] porphyrin and their rare earth complex liquid crystalline

Three series of porphyrin liquid crystalline compounds, [5‐(p‐alkoxy)phenyl‐10, 15, 20‐tri‐phenyl] porphyrin and their rare earth complexes (Tb (III), Dy (III), Er (III), Yb (III)), with a hexagonal columnar discotic columnar(Col_h) phase have been synthesized. These compounds were characterized by elemental analysis, molar conductances, UV‐visible spectra, infrared spectra, luminescence spectra, and cyclic voltammetry. These compounds exhibit more than one mesophases, which transition points of temperature change from ?33.6 to 16.0 °C, and transition points of temperature for isotropic liquid also increase from 4.9 to 38.2 °C, with increasing chain length. Their surface photovoltage (SPV) response have also been investigated by the means of surface photovoltage spectroscopy (SPS) and field‐induced surface photovoltage spectroscopy (EFISPS). It was found that their SPV bands are analogous with the UV‐visible absorption spectra and derived from the same transition. Copyright © 2007 John Wiley & Sons, Ltd.