Structural characterization of hierarchically porous alumina aerogel and xerogel monoliths

Detailed nanostructures have been investigated for hierarchically porous alumina aerogels and xerogels prepared from ionic precursors via sol–gel reaction. Starting from AlCl₃·6H₂O and poly(ethylene oxide) (PEO) dissolved in a H₂O/EtOH mixed solvent, monolithic wet gels were synthesized using propylene oxide (PO) as a gelation initiator. Hierarchically porous alumina xerogels and aerogels were obtained after evaporative drying and supercritical drying, respectively. Macroporous structures are formed as a result of phase separation, while interstices between the secondary particles in the micrometer-sized gel skeletons work as mesoporous structures. Alumina xerogels exhibit considerable shrinkage during the evaporative drying process, resulting in relatively small mesopores (from 5.4 to 6.2 nm) regardless of the starting composition. For shrinkage-free alumina aerogels, on the other hand, the median mesopore size changes from 13.9 to 33.1 nm depending on the starting composition; the increases in PEO content and H₂O/EtOH volume ratio both contribute to producing smaller mesopores. Small-angle X-ray scattering (SAXS) analysis reveals that variation of median mesopore size can be ascribed to the change in agglomeration state of primary particles. As PEO content and H₂O/EtOH ratio increase, secondary particles become small, which results in relatively small mesopores. The results indicate that the agglomeration state of alumina primary particles is influenced by the presence of weakly interacting phase separation inducers such as PEO.     

Layer structure estimation of three‐dimensional crystal and two‐dimensional molecular film for fluorinated comb copolymers

Comb copolymers containing both hydrogenated and fluorinated side‐chains were prepared by copolymerization using acrylic or methacrylic monomers in several ratios. The crystal structures of these copolymers and layer structures of their organized molecular films were investigated by wide‐angle X‐ray diffraction (WAXD), small‐angle X‐ray scattering (SAXS), and out‐of plane X‐ray diffraction. Further, to selectively estimate the regularity of shorter fluorocarbon side‐chains, organized molecular films of copolymers were investigated by polarized near‐edge X‐ray adsorption fine structure (NEXAFS) spectroscopy. From the results of these measurements, it was inferred that these copolymers formed highly ordered layer structures, and a long spacing was predominantly determined by the arrangement of hydrogenated side‐chains, except in copolymers having extremely high fluorocarbon contents. In the case of the organized molecular films, the fluorinated side‐chains of methacrylate copolymers cannot form a highly ordered arrangement, whereas those of acrylate copolymers were oriented on monolayers. However, in both cases, the hydrogenated side‐chains predominantly formed layer structures in the organized films, and the fluorinated side‐chains did not contribute to the formation of the layer structures. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 534–546, 2008     

Multiwalled carbon nanotube promotes crystallisation while preserving co-continuous phase morphology of polycarbonate/polypropylene blend

The influence of multiwalled carbon nanotubes (MWCNTs) on phase morphology, lamellar structure, thermal stability, melting behaviour and isothermal crystallisation kinetics of polycarbonate/polypropylene (PC/PP) blend nanocomposites has been investigated. Both neat blends and PC/PP (60/40)/MWCNT nanocomposites were prepared by melt mixing method. Morphological analyses were performed by high-resolution X-ray micro-computed tomography and scanning electron microscopy. The co-continuous morphology of the blend was retained irrespective of MWCNT loading. In addition, a substantial refinement in the co-continuous structure was observed. Wide angle and small angle X-ray scattering studies were used to analyse the structural properties of the blend nanocomposites. The addition of MWCNT increases the long period of polypropylene. The influence of addition of MWCNT on the crystallisation temperature and equilibrium melting temperature (Tm°) of polypropylene was followed. The MWCNTs promote crystallisation rate of polypropylene in the blend nanocomposites.     

Effect of liquid oils on the properties of multiple emulsions containing liquid crystals

Recently, many cosmetic researchers have been focused on multiple emulsions due to better performance. Limited application of multiple emulsions has been attributed to their instability, which can be resolved by the presence of liquid crystals. Multiple emulsions containing liquid crystals are affected by various formulation parameters, such as liquid oils. In this paper, the influence of liquid oils on the formation mechanism was studied. Besides, stability, small-angle x-ray scattering (SAXS) spectra analysis, and rheological analysis of the emulsions were investigated as well. The results showed that when the gap of the polarity between inner oils and external liquid oils is greater, the multiple structures were more easily formed. Multiple emulsions containing liquid crystals were superior in stability to multiple emulsions prepared in the same way with liquid oils that did not form liquid crystals. SAXS indicated that the liquid crystal orientation was lamellar. Rheological analysis indicated that the different structure emulsions showed shear-thinning behavior. The presence of liquid crystal decreased the viscosity and resulted in pseudoplastic enhancement. Both the storage modulus (G′) and the loss modulus (G″) of multiple emulsions were slightly higher than those of O/W-type emulsions, implying the existence of multiple structures.     

Small strain behavior of polyethylene: In situ SAXS measurements

Stack lamella deformation depends on their orientation with respect to the loading axis, the intrinsic properties of the lamellae, and the mechanical coupling between crystalline and amorphous phases. The aim of this work is to investigate the influence of the stress transmitter (ST) density and the crystallinity X_c on the local deformation. A wide experimental campaign has been undertaken on several polyethylenes with controlled molecular parameters and subjected to different thermal treatments. The ST density has been evaluated by the natural draw ratio and calculated by the Brown's model. The local deformation was measured by SAXS along a tensile test by using the long period stretching of the equatorial lamella stacks. The ratio ε_local/ε_macro was found to be a constant close to 0.5. This surprising low value has highlighted that the equatorial regions could be either the stiffest zone of the spherulite or submitted to a lower stress. It is proposed that the stability of the ratio ε_local/ε_macro is the result of two opposite phenomena: On one hand, the increase of X_c leads to unload the equatorial regions due to partial percolation of the crystalline phase and so decreases the stresses. On the other hand, when increasing X_c, the ST density decreases which causes the decrease in the local equatorial modulus. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 1535–1542, 2010     

Physical properties of films made of copoly(ether-imide)s with long poly(ethylene oxide) segments

Polyimides having long poly(ethylene oxide), PEO, moieties in the main chain have been synthesized by a classical two-steps polycondensation method with good yield and high molecular weight. In contrast with previous works on this topic, essentially full conversion of the polyamic acid to polyimide was attained by heating at relatively low temperatures (around 160 °C).These copolyimides undergo an increase of phase separation between the PEO part and the polyimide one after a thermal annealing. This phase separation increases gas separation properties of membranes made up of these copolymers. An exhaustive study of polymer properties as a function of the thermal treatment has been carried out in order to figure out the origin of this behavior. The analysis performed included TGA, DSC, SAXS and mechanical testing.The polymers studied in this paper have medium thermal stability. In fact, degradation of the polyether chain under nitrogen takes place at temperatures above 300 °C. However, their thermal stabilities were much lower under oxidant atmosphere.     

Influence of clay surface modification with urethane groups on the crystallization behavior of in situ polymerized poly(butylene succinate) nanocomposites

The crystallization behavior and fine structure of poly(butylene succinate) (PBS) nanocomposites with intercalation (30B20) and exfoliation (30BM20) morphologies, respectively, were investigated via isothermal crystallization testing and synchrotron small-angle X-ray scattering (SAXS). The dynamic viscosity of 30BM20 was markedly increased due to favorable interactions between the PBS matrix and the urethane group on the clay surface. However, 30BM20 showed similar crystallization rates to that of homo PBS because the surface urethane modification for 30BM20 precluded PBS matrix from the metallic group into clay to difficult in contact with each other, resulting in a reduced nucleation activity for the metallic group. SAXS profiles revealed that the long period and amorphous region size for 30B20 drastically decreased during isothermal crystallization. Meanwhile, 30BM20 was similar to those of homo PBS. This result also supports the above explanation for isothermal crystallization behavior. Considering all results in total, the introduction of a urethane modification considerably enhanced the physical properties of PBS but caused delayed crystallization rates.     

小角X射线散射法研究CH2Cl2,CHCl3和CCl4对PE液晶结构的影响

采用小角X射线散射法研究了CH_2Cl_2、CHCl_3和CCl_4对磷脂酰乙醇胺(PE)液晶结构影响的机理.CH_3Cl_2、CHCl_3和CCl_4对PE液晶结构影响的差别主要是其空间旋转电子云密度分布形状不同所致.空间旋转电子云密度分布呈椭球状的物质有使PE液晶形成六角形H_1相的趋向;呈圆锥状的物质有诱发PE液晶形成立方六角相的趋向;呈球状的物质有使PE液晶形成片层立方相的趋向.     

Crystallization behavior of isotactic polypropylene based nanocomposites

The effect of clay dispersion on the crystallization behavior of isotactic polypropylene (iPP)-based nanocomposites is reported. The T _m⁰ of the materials was calculated by the method proposed by Marand, the kinetics of crystallization was evaluated by the Avrami analysis and also the Hoffman-Lauritzen theory of crystallization regimes was applied. Montmorillonite was found to depress T _m⁰, to enhance the rate of crystallization and to ease the chain folding of macromolecules. These effects were magnified if clay was exfoliated, rather than intercalated.     

Poly(Pyridinium Salt)s Containing 2,7-Diamino-9,9′-Dioctylfluorene Moieties with Various Organic Counterions Exhibiting Both Lyotropic Liquid-Crystalline and Light-Emitting Properties

A series of poly(pyridinium salt)s-fluorene main-chain ionic polymers with various organic counterions were synthesized by using ring-transmutation polymerization and metathesis reactions. Their chemical structures were characterized by Fourier Transform Infrared (FTIR), proton (¹H), and fluorine 19 (¹⁹F) nuclear magnetic resonance (NMR) spectrometers. These polymers showed a number-average molecular weight (M_ns) between 96.5 and 107.8 kg/mol and polydispersity index (PDI) in the range of 1.12–1.88. They exhibited fully-grown lyotropic phases in polar protic and aprotic solvents at different critical concentrations. Small-angle X-ray scattering for one polymer example indicates lyotropic structure formation for 60–80% solvent fraction. A lyotropic smectic phase contains 10 nm polymer platelets connected by tie molecules. The structure also incorporates a square packing motif within platelets. Thermal properties of polymers were affected by the size of counterions as determined by differential scanning calorimetry and thermogravimetric analysis measurements. Their ultraviolet-visible (UV-Vis) absorption spectra in different organic solvents were essentially identical, indicating that the closely spaced π-π* transitions occurred in their conjugated polymer structures. In contrast, the emission spectra of polymers exhibited a positive solvatochromism on changing the polarity of solvents. They emitted green lights in both polar and nonpolar organic solvents and showed blue light in the film-states, but their λ_em peaks were dependent on the size of the counterions. They formed aggregates in polar aprotic and protic solvents with the addition of water (v/v, 0–90%), and their λ_em peaks were blue shifted.