不同类型聚合物溶液对采油残余油的作用机理研究

通过实验测定了HPAM溶液和黄原胶溶液的流变性、在多孔介质中的流变性和残余阻力系数 ,计算了衰竭层效应 .用不同的浓度和注入速度进行了驱油实验 .提出聚合物分子缠结作用的增强不仅引起表观粘度增加或衰竭层厚度降低 ,而且使平行于油水界面的拉动残余油的力增加 ,从而使残余油饱和度降低 ,采收率提高 .随浓度增加 ,HPAM溶液的表观粘度和残余阻力系数增加 ,衰竭层厚度减小 ;黄原胶溶液的浓度高于缠结浓度时 ,衰竭层厚度和表观粘度变化不大 .注入速度增加时 ,两种聚合物溶液的衰竭层厚度均降低 ,HPAM溶液的残余阻力系数不变 ,粘弹性增加 ;而黄原胶溶液的残余阻力系数下降 .不同浓度和注入速度情况下两种聚合物溶液的驱油结果证实了文中提出的聚合物分子缠结作用和衰竭层效应对残余油的作用机理 .分子结构的不同是造成两种聚合物溶液在多孔介质中渗流规律和对残余油作用机理的差别的根本原因 .     

PBT／PC共混体系流变性能与形态结构研究

采用毛细管流交仪测定了ＰＢＴ／ＰＣ共混物的表观粘度、剪切应力，观察了不同共混物组成和不同温度下共混物的流变行为，并借助扫描电镜对共混物和微观形态结构进行分析。结果表明：ＰＢＴ／ＰＣ熔体共混物的流变行为接近假塑性流体．温度对共混物的流变行为影响很大，共混物的熔体粘度在ＰＢＴ／ＰＣ为９０／１０和６０／４０时呈双极值．共混物为两相结构，ＰＣ含量为４－５０％时呈两互锁结构。     

相反转技术制备环氧树脂水基体系——相反转过程的流变行为研究

对高乳化剂浓度下的相反转发展过程的流变行为进行了应力扫描、动态频率扫描实验表征．结果表明，乳化剂浓度较高时，体系发生完全相反转；体系在相反转点前为Ｗ／Ｏ结构，其粘度几乎不随剪切应力的改变而改变，表现为牛顿流体行为；体系在相反转点后为Ｏ／Ｗ结构，具有很高的粘弹性，并且在较高剪切应力下表现为典型的假塑性．这是由于高分子水基微粒间通过其表面覆盖的表面活性剂与水形成氢键而产生了一种静态结构，此结构在较高剪切应力作用下破坏而导致假塑性．     

Rheological properties of the aqueous mixtures of cationic-anionic surfactants

The rheological properties of the aqueous mixtures of cationic-anionic surfactants, both in single-phase systems and in aqueous two-phase systems, have been studied. Bizarre rheological properties —negative thixotropy, viscoelasticity and hihg viscosity of shear rate dependent at relatively low concentration — have been observed. An unusual viscosity change, that is, viscosity lowering with increasing concentration, was obtained. The negative thixotropy might be due to the existence of lamellar or sheet-like micelles, viscoelasticity might be induced by rodlike and lamellar or sheet-like micelles, the high viscosity might be a consequence of the formation of network by long rodlike micelles and the concentration-induced viscosity lowering could be interpreted in terms of the decrease of micellar dimensions with concentration.     

Studies of sodium humate/polyacrylamide/clay hybrid hydrogels. I. Swelling and rheological properties of hydrogels

A type of novel hybrid hydrogels from sodium humate (SH), polyacrylamide (PAM), and hydrophilic Laponite clay were prepared using potassium persulfate (KPS) as the initiator and N,N′-methylenebisacrylamide (MBA) as the cross-linker. The structures of the hydrogels were characterized by field emission scanning electron microscope and FTIR. Their swelling properties, swelling mechanism and rheological properties were also investigated. Experiments show that the composite is heterogeneous in the PAM/SH hydrogel system, while the clay collaborates with SH and improves the network structure of PAM/SH/clay hydrogel. High water-absorbing capability is shown for both hydrogel systems. Han plot proves that clay and SH are compatible with PAM for PAM/SH/clay hydrogels.     

界面改性剂对刚性粒子增韧尼龙6熔体流变行为的影响

研究了界面改性剂对高岭土增韧尼龙６熔体流变行为的影响,并与硅烷偶联剂ＫＨ５５０进行了比较．结果表明,ＫＨ５５０的加入明显降低了高岭土填充尼龙６熔体的粘度和弹性,而界面改性剂显著地增强了它的粘度和弹性．这一差别应归因于同ＫＨ５５０相比,界面改性剂更有效地增强了高岭土与尼龙６基体之间的界面结合和其自身的回弹性能．同时,界面改性剂的用量对高岭土填充尼龙６流变行为具有很大影响．当界面改性剂的用量为高岭土和尼龙６总量的２％时,界面改性剂在高岭土表面上趋于“饱和”,再增加界面改性剂的用量,对流变行为的影响不大．     

Rheological behavior in blends of PET with ionomeric polyester

The rheological behavior and the morphology in blends of polyethylene terephthalate (PET) with ionomeric polyester were investigated over a wide range of different blending ratios. The ionomeric polyester is derived from PET modified through copolycondensation with sulfonate moiety, sodiosulfo isophthalate (Na-SIP), iso-phthalic acid (IPA) and polyethylene glycol (PEG). The results showed that the apparent viscosity and non-Newtonian index of the PET/ionomeric polyester blend system had a nonlinearity change with the change of the blend ratio of PET/ionomeric polyester. The anomaly of the viscous flow activation energy change was found as the content of ionomeric polyester was about 40% (w/w) in the blend system, suggesting the presence of physical cross-linked structure formed by strong polar tangling points and the phase separation owing to poor compatibility between the PET and ionomeric polyester. The morphology and thermal behavior of the blends were observed, respectively, with differential scanning calorimetry (DSC) and atomic force microscopy (AMF).     

Influence of high pressure treatment on rheological and other properties of egg white

Abstract

The paper deals with the influence of high pressure treatment of fresh egg white on its properties and protein composition (individual amino-acids predicted as a function of pressure and time levels). The rheological properties are changed by high pressure from Newtonian to non-Newtonian behaviour, with increasing apparent viscosity as the pressure and time increased. The pH, whipping ability, foam stability, gel strength of heat induced gels after treatment and the whole protein content, were also predicted.

The results showed that the foam stability is increased with increasing pressure and time of processing. The foam volume is also increased with pressure. The pH did not change with pressure or time of processing. Composition of proteins as indicated by individual amino-acids did not exhibit statistically important changes. Gel strength of heat induced gels prepared from previously pressured liquid whites showed no important change of values with pressure or time of treatment. The modulus of elasticity showed a decrease for samples pressured to 400 MPa for 5 up to 15 minutes.     

Electron spin resonance in pyrolyzed lignin

An investigation has been made into electron spin resonance (ESR) occurring in the ranges of carbons prepared from periodate lignin by vacuum pyrolysis. Line shape, line width, g-factors, saturation effects, and free spin concentration have been measured and the effect of oxygen on these parameters has been examined. A g-shift and lines with inhomogeneous broadening have been observed. In the presence of oxygen the lower-temperature carbons showed an unexpected increase in the detectable free spin concentration. The discussion includes factors affecting the nature of the free spins in the pyrolyzed material.     

Electrical conductivity of poly(vinylidene fluoride)/polyaniline blends under oscillatory and steady shear conditions

Blends of poly(vinylidene fluoride) (PVDF) and polyaniline (PAni) were prepared through melt blending in a batch mixer. The morphology, rheological behavior and electrical conductivity were investigated through transmission electron microscopy (TEM) and combined electro-rheological measurements. Through TEM analysis, it was possible to observe that all blends showed typical phase separation with the presence of conductive polymer aggregates. Deformations imposed during a strain sweep caused, not only disturbance of the linear viscoelastic behavior, but also changes in electrical conductivity. The oscillatory shear altered the morphology, breaking the PAni domains into smaller ones. This effect increases the distance between them and, consequently, resulted in a decrease of the electrical conductivity. The measurements under quiescent conditions and steady shear proved that the disturbance in morphology for PVDF/PAni system is non-recoverable. Through combined electrical and rheological measurements, it was possible to achieve good correlation between the electrical and flow behavior of PVDF/PAni blends.