二维材料改性水性聚氨酯防腐涂料的研究进展

水性聚氨酯涂料作为一种新兴的环保涂料,在防腐领域得到了广泛应用。然而,水性聚氨酯涂料交联密度低,耐水性稍差,不利于其长效防腐性能。利用具有独特物理化学特性的二维材料作为水性聚氨酯的填料,可以有效改善其性能。本文主要介绍了三种二维材料(石墨烯、MXene和六方氮化硼)作为填料与水性聚氨酯进行复合,并重点介绍了石墨烯、MXene和六方氮化硼的改性方法,并对水性聚氨酯复合涂层的性能进行了阐述和比较,最后对未来二维材料/水性聚氨酯的复合材料的发展和应用进行了展望。     

Synthesis and Characterization of a One- dimensional Molybdenum Oxide （H2enMe）[Mo3O10]

A hybrid organic-inorganic material (H2enMe)[Mo3O10] (C3H12Mo3N2O10, Mr = 523.97) has been synthesized under hydrothermal conditions and its crystal structure was determined by X-ray diffraction. It crystallizes in the orthorhombic system, space group Pnma with a = 12.430(2), b = 7.6089(12), c = 11.9553(19) , V = 1130.7(3) 3, Dc = 3.078 g/cm3, Z = 4, μ(MoKa) = 3.328 mm1, F(000) = 1000, the final R = 0.0256 and wR = 0.0716 for 1314 observed reflections with I > 2σ(I). A total of 11780 reflections were measured and 1325 were unique (Rint = 0.0244). It consists of infinite one-dimensional edge-sharing MoO6 octahedral chains with [Mo3O10]2 moieties. The protonated diaminopropane cations are located between the chains and linked to the oxygen atoms of the inorganic skeletal backbones by hydrogen bonds. It is indicated that the as-synthesized compound displays photochromic property in the solid state.     

石墨烯负载高活性Pd催化剂对乙醇的电催化氧化

以石墨粉为原料, 采用Hummers法液相氧化合成了氧化石墨(GO), 然后用化学一步还原制得石墨烯负载钯催化剂. X射线衍射(XRD)、透射电镜(TEM)表征表明, Pd在石墨烯载体上有较好的分散度, 粒径为3-5 nm. 电化学活性面积(EASA)、循环伏安(CV)、计时电流(CA)和计时电位(CP)等电化学测试表明, 与传统Pd/Vulcan XC-72相比, Pd/石墨烯催化剂对碱性介质中乙醇电催化氧化的催化活性有了很大的提高.     

傅里哀变换红外发射光谱法研究金属氧化物催化剂——Ⅰ.实验建立及氧化钼的还原-氧化研究

本文报导了傅里哀变换红外发射光谱法研究多相氧化物催化剂的实验装置的建立及实验条件的考察。设计加工了一个温度范围宽,可在各种气氛和真空条件下原位研究氧化物催化剂的红外发射池。以MoO_3为例,考察了样品厚度,测试温度对发射光谱的影响。当样品量小于1mm·cm~(-2)时,随样品量增加,谱峰强度线性增加,但峰形不发生变化。当样品量高于1mg.cm~(-2)时,随样品量增加,谱图严重畸变。随样品温度升高,谱峰强度近似线性增加。并用该方法研究了MoO_3在还原和再氧化过程中表面氧物种的变化。结果表明桥式MO?O?Mo物种比端基Mo=O物种较易还原,再氧化时,Mo=O物种比Mo?O?Mo物种优先形成。     

Pd–Co bimetallic nanoparticles supported on graphene as a highly active catalyst for Suzuki–Miyaura and Sonogashira cross-coupling reactions

Graphene (G) supported Pd–Co bimetallic nanoparticles (NPs) as a highly active catalyst was prepared by a chemical reduction method and used for coupling reactions. With the characterization of X-ray diffraction, X-ray photoelectron spectroscopy, transmission electron microscopy, and Raman spectrum, the composition of resulting Pd–Co material was identified to be alloy structural. The Pd–Co (1:1)/G exhibited the highest catalytic activity for the Sonogashira-type coupling reactions and also exerted satisfied catalytic activity and recycle stability for Suzuki–Miyaura cross-coupling reactions. This Pd–Co/G material also possessed other advantages such as low-cost, easy recycled from reaction system by a magnet for their magnetic property, and easy experimental handling.     

可充镁电池正极材料PTMA/石墨烯

本文制备了聚4-甲基丙烯酸-2,2,6,6-四甲基哌啶-1-氮氧自由基酯(PTMA)/石墨烯纳米复合材料,并报道了其作为可充镁电池正极材料的电化学性能.通过傅里叶变换红外(FTIR)光谱、扫描电镜(SEM)、透射电镜(TEM)表征复合材料的结构和形貌;循环伏安和恒电流充放电测试其电化学性能.粒径10 nm左右的PTMA颗粒分散在具有导电作用的石墨烯表面;在"一代"电解液Mg(AlCl2BuEt)2/四氢呋喃(THF)(0.25 mol L-1)中,22.8mA g-1充放电电流密度下,PTMA/石墨烯复合材料的起始放电容量可达到81.2 mAh g-1.研究结果表明,含有自由基的有机化合物可以作为可充镁电池的一类新型正极材料,可以进一步通过使用具有高氧化分解电压的电解液来提高其放电容量.     

石墨烯和硼氮类石墨烯对LiFePO4表面结构的改进及其电导的促进作用

利用密度泛函理论研究石墨烯和硼氮类石墨烯包覆对LiFePO₄ (010)表面结构和电导性质的影响. 结果表明包覆层和LiFePO₄ (010)表面之间的相互作用可以改善LiFePO₄ (010)表面的电导性能. 石墨烯包覆LiFePO₄ (010)表面后, 禁带宽度从3.3 eV减小到2.1 eV. 硼氮类石墨烯包覆LiFePO₄ (010)表面后, 虽然其价带顶和导带底仍由Fe的3d轨道贡献, 但禁带中出现两个间隔为0.6 eV的带隙态, 由硼氮类石墨烯与LiFePO₄(010)表面有直接接触并形成共价键的B原子和N原子贡献.     

正丁基氯化镁还原氧化石墨烯的表征

采用元素分析、红外光谱(FTIR)、X射线光电子能谱(XPS)、拉曼光谱、X射线衍射(XRD)、固体¹³C核磁共振波谱(¹³C MAS NMR)、热失重分析(TGA)、导电率测试以及原子力显微镜(AFM)等手段对正丁基氯化镁还原的氧化石墨烯进行了系统的表征. 结果表明, 正丁基氯化镁可以有效还原氧化石墨烯, 随着其用量的增加, 氧化石墨烯还原程度增加, 碳/氧摩尔比升高, 片层间距减小, 热稳定性增强, 导电率增大(可达3.6×10² S/m). 还原后部分氧化石墨烯片层发生聚集.     

石墨烯在有机/聚合物太阳能电池中的应用进展

近年来有机/聚合物太阳能电池得到国内外研究者的广泛关注,但其目前较低的能量转换效率有待进一步提高以满足市场化的需求。本文综述了新型二维电子材料石墨烯及其衍生物在有机/聚合物太阳能电池的受体材料、电极材料、电荷传输材料方面的研究进展,分析了石墨烯功能化的方法以及石墨烯衍生物应用于有机太阳能电池中的性能参数,最后对石墨烯及其衍生物的合成和修饰方法进行展望,以期将来在有机太阳能电池材料中得到更好的应用。     

Multi‐responses Methodology Applied in the Electroanalytical Determination of Hair Dye by Using Printed Carbon Electrode Modified with Graphene

This paper describes a rapid and sensitive method for determination of the hair dye Basic Blue 41 in wastewater samples using screen‐printed carbon electrodes modified with graphene (SPCE/Gr). The method is based on the reversible reduction of azo groups of the dye at potential of ?0.23 V/?0.26 V, where both the anodic and cathodic currents increased 1,300 % when compared to screen‐printed carbon (SPCE) and glassy carbon electrodes (GCE). The optimization of a square wave voltammetric method was performed by means of 2³ factorial design, Doehlert matrix and multi‐response assays, and the best parameters were: frequency (54.8 Hz), step potential (6 mV), pulse amplitude (43.7 mV) and pH 4.5. The analytical curve was constructed from 3.00×10^?8 to 2.01×10^?6 mol L^?1, with detection and quantification limits of 5.00×10^?9 and 1.70×10^?8 mol L^?1, respectively. The repeatability of the method evaluated for 10 consecutive measurements at concentrations of 1.70×10^?7 mol L^?1 and 1.70×10^?6 mol L^?1, showed relative standard deviation of 3.56 and 0.57 %, respectively. The sensor based in SPCE/Gr was successfully applied in wastewater samples collected from a drinking water treatment plant and validated by comparison with HPLC‐DAD method with good accuracy.