The preparation and structure of 1,4,5,6,7,7-hexachloro-2-endo-ferrocenylhydroxymethyl-3-endo-hydroxymethyl-5-norbornene

The crystal structure of a novel ferrocene derivative with potential flame-retardant/smoke-suppressant activity, 1,4,5,6,7,7-hexachloro-2-endo-ferrocenyl-hydroxymethyl-3-endo-hydroxymethyl-5-norbornene, has been determined. Some of the carbon–carbon bonds within the chlorendic residue are unusually long, and there is no interaction between the hydroxyl groups and the iron atom. There is evidence of intramolecular hydrogen bonding between the two hydroxyl groups.     

Synthesis and properties of thermosetting polymers from a phosphorous‐containing fatty acid derivative

A new phosphorous‐containing fatty acid diepoxide was obtained from 10‐undecenoyl chloride and 10‐(2′,5′‐dihydroxyphenyl)‐9,10‐dihydro‐9‐oxa‐10‐phosphaphenanthrene‐10‐oxide and crosslinked with 4,4′‐diaminodiphenylmethane and bis(m‐aminophenyl)methylphosphine oxide. The properties of the thermosetting materials were evaluated by differential scanning calorimetry, dynamic mechanical thermal analysis, thermogravimetric analysis, and limiting oxygen index (LOI). Thermal and thermooxidative degradation was studied by gas chromatography/mass spectrometry, FTIR, ³¹P magic angle spinning NMR spectroscopy, and scanning electron microscopy. LOI values indicate good flame‐retardant properties that are related to the formation of a protective phosphorous‐rich layer that slowed down the degradation and prevented it from being total. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 5630–5644, 2006     

Optical properties of In2O3 oxidized from InN deposited by reactive magnetron sputtering

Unintentionally doped and zinc-doped indium nitride (U-InN and InN:Zn) films were deposited on (0 0 0 1) sapphire substrates by radio-frequency reactive magnetron sputtering, and all samples were then treated by annealing to form In₂O₃ films. U-InN and InN:Zn films have similar photon absorption characteristics. The as-deposited U-InN and InN:Zn film show the absorption edge, ∼1.8-1.9 eV. After the annealing process at 500 °C for 20 min, the absorption coefficient at the visible range apparently decreases, and the absorption edge is about 3.5 eV. Two emission peaks at 3.342 eV (371 nm) and 3.238 eV (383 nm) in the 20 K photoluminescence (PL) spectrum of In₂O₃:Zn films were identified as the free-exciton (FE) or the near band-to-band (B-B) and conduction-band-to-acceptor (C-A) recombination, respectively.     

Thermal properties of poly(styrene) containing brominated aryl phosphate additives

General purpose poly(styrene) is a large volume commodity polymer widely used in a range of applications. For many of these the presence of an additive to impart some flammability resistance is required. Most commonly, brominated aromatics are used for this purpose. As the polymer undergoes combustion these compounds decompose to generate bromine atoms and/or hydrogen bromide which escape to the gas phase and trap flame propagating radicals. While these species are effective in inhibiting flame propagation they present the opportunity for loss of halogen to the atmosphere. For this reason, the use of these compounds is being limited in some parts of the world. Phosphorus compounds, on the other had, impart a flame retarding influence by promoting char formation at the surface of the burning polymer. This prevents heat feedback to the polymer and consequent pyrolysis to generate fuel fragments. The combination of both bromine and phosphorus present in a single compound might generate a superior flame-retarding additive in that both modes of retardancy might be promoted simultaneously. Should this be the case smaller amounts of additive might be necessary to achieve a satisfactory level of flame retardancy. A series of such additives, brominated aryl phosphates, has been synthesized and fully characterized spectroscopically. Blends of these additives, at various levels, with poly(styrene) have been examined by DSC, TG and in the UL-94 flame test. The flammability of the polymer is dramatically diminished by the presence of the additive.     

多组分单体接枝聚丙烯/尼龙6反应共混物结晶行为研究

用多组分熔融接枝的方法将甲基丙烯酸缩水甘油酯 (GMA)和苯乙烯 (St)共同接枝到聚丙烯 (PP)上 ,制得具有较高GMA接枝率的多单体接枝聚丙烯 ,PP g (GMA co St) .将PP g (GMA co St)与尼龙 6 (PA6 )进行共混 ,利用扫描电镜 (SEM) ,差示扫描量热计 (DSC)和广角X射线衍射 (WAXD)对共混物的形态和结晶进行了研究 .在共混过程中 ,PP g (GMA co St)与PA6反应原位生成了PP g PA6 ,有效改善了共混物的相容性 ,分散相尺寸明显减小 .在PP g (GMA co St) PA6为 3 7的体系中 ,PP g (GMA co St)出现分级结晶现象 ,其在较低温度下的结晶属于均相成核结晶 .在PP g (GMA co St) PA6为 7 3的体系中 ,由于PA6相分散细微 ,在通常结晶温度下不结晶 ,而是在低温下均相成核与PP g (GMA co St)同时结晶 .WAXD证实体系中接枝PP ,PA6为分别结晶 ,无共晶或新的晶型产生     

四种硝基苯的电化学行为及其反应活性的理论计算

在滴汞电极上研究了硝基苯、对硝基甲苯、间二硝基苯及2，4-二硝基氯苯的电化学行为，并用量子理论对四种硝基苯化合物的反应活性进行了预测，理论与试验结果基本一致，据此提出了预测分子的电化学活性的方法。     

Preparation of flame retardant polyamide 6 composite with melamine cyanurate nanoparticles in situ formed in extrusion process

This paper is focused on in situ preparation of melamine cyanurate (MCA) nanoparticles from reaction of melamine (MEL) and cyanuric acid (CA) and their flame retardant polyamide 6 (PA6) composite in the extrusion process through a novel reactive processing method. Fourier transform infrared (FT-IR), X-ray diffraction (XRD), differential scanning calorimetry (DSC), thermogravimetric analysis (TGA) and scanning electron microscopy (SEM) were utilized to characterize the in situ formed MCA nanoparticles and their blends with PA6. Introduction of pentaerythritol (LTP) and water-bound plasticizer dioctyl phthalate (DPT) into the extrusion reaction system greatly inhibits the evaporation of water required for melamine and cyanuric acid reaction at high temperature (higher than 180 °C), laying a foundation for successful in situ preparation of MCA through reactive processing. XRD and FT-IR measurements indicate that under the effect of pentaerythritol, dioctyl phthalate and water, melamine really reacts with cyanuric acid to in situ form MCA in extrusion process. The reaction degree is close to 100%. A very important finding through SEM is that the in situ formed MCA particles, which were found to have aspect ratio of about 7.5, radial size in the range of 70-300 nm (mostly 70-90 nm) and crystallite size of less than 22 nm, are uniformly dispersed in the matrix PA6 at nanoscale. The in situ formed MCA nanoparticles greatly improve the flame retardancy and the mechanical properties of flame-retarded PA6 materials, and the introduced plasticizer dioctyl phthalate also ameliorates the related impact property. The obtained flame-retarded PA6 materials have good comprehensive performance with flame retardancy UL-94 V-0 rating at 1.6 and 3.2 mm thickness, tensile strength 48.0 MPa, elongation at break 106.3% and Izod notched impact strength 8.92 kJ/m². Compared with flame-retarded PA6 material with in situ formed MCA, the one prepared through conventional blending of PA6 with commercial MCA product has improved tensile strength but deteriorated impact strength and flame retardancy.