A study on anisotropy of L2 to L3 Coster-Kronig transition (f23) for Th and U elements

The Coster-Kronig transition, f₂₃, was determined using differential fluorescence cross sections of L_l X-ray for Th and U. The targets were irradiated an Am-241 radioisotope at the different incident angle. The L_l X-rays were counted with a Si (Li) detector at the different scattering angle varying from 60° to 90° at 10° intervals. For each angle, the Coster-Kronig transition probability, f₂₃, was found. An obtained Coster-Kronig transition probability value was fitted versus emission angle. According to present results we can say that the Coster-Kronig transition probability, f₂₃, shows isotropic distribution.     

C2（a 3Πu）+NO 的反应机理研究

在G2 (CC ,MP2 )理论水平上研究了C2 (a3 Πu)自由基与NO分子的反应 .计算了反应体系最低二重态势能面上各驻点的构型参数、振动频率和能量 ,揭示了此反应存在两种反应机理 :由NO中的O原子进攻C2 自由基形成CCON中间体的CCON机理和NO中的N进攻C2 自由基形成CCNO中间体的CCNO机理 ,分析了对应与这两种反应机理的五个可能的反应通道 ,得出了由NO中的N原子进攻3 C2 自由基 ,生成中间体CCNO自由基 ,最终得到产物CN +CO的通道是最有利的通道 .     

Load-Carrying Capacity of Circular Plates Made of a Fiber-Reinforced Composite

The load-carrying capacity of circular plates made of a fiber-reinforced composite and loaded with axisymmetric transverse forces under axisymmetric boundary conditions is investigated. The plates can be freely supported or clamped along their contour. To the known yield condition used, in the plane of main bending moments, there correspond irregular hexagons, which depend on the mechanical properties of composite constituents and some characteristic geometrical parameters. It is shown that, depending on the ratio of ultimate radial and circumferential bending moments, in the plastic state, the circular plates (the central part of the clamped plates) take the form of a cone or a frustum of cone. For each of the cases, the limit load is found, which is a function of the above-mentioned mechanical parameters. The statically allowable fields of bending moments and the corresponding allowable fields of deflection rates are determined. The solutions found are exact. Special cases for the freely supported plates are analyzed, and the results obtained are presented in the form of graphs.__________Translated from Mekhanika Kompozitnykh Materialov, Vol. 41, No. 2, pp. 177–192, March–April, 2005.     

激光二极管端面抽运的棒状Yb：YAG激光器

分析了影响激光二极管抽运Yb：YAG激光器调Q效率的参量，推导了激光二极管端面脉冲抽运Yb：YAG晶体的速率方程，解出了双程抽运情况下的净抽运量子产率。利用数值计算方法，模拟了净抽运量子产率与晶体长度，抽运光脉冲宽度等关系，得出晶体长度的优化可以提高Yb：YAG激光器输出效率。计算了词Q Yb：YAG激光器的最大增益、最大储能，分析了放大自发辐射对于Yb：YAG能量存储的影响。同时给出了激光二极管端面抽运调Q Yb：YAG优化设计方法。这些分析和计算为实际器件的研制提供参考。     

17N+197Au反应中碎片与中子的符合测量

在3?3?.4MeV/u ¹⁷N束轰击¹⁹⁷Au靶产生的反应中,利用放置于不同角度组合的17个中子探测器(4°—83°)和14个半导体望远镜(2.3°—9.0°)对反应产物碎片与中子进行了符合测量.经对所得实验角分布积分得到Z=3—6元素的同位素产额分布.在参加者-旁观者模型框架下,采用¹⁷N原子核内部的不同密度分布计算了同位素产额分布并与实验数据做比较.     

The solution of a convection–diffusion–reaction equation arising from cathodic reduction in a pulsating crack

This paper derives the convection–diffusion-reaction equation governing the reaction between the dissolved oxygen in sea-water and the steel walls of a pulsating crack. By the neglect of the diffusion term it is shown that an exact solution of the convection-reaction equation can be obtained. A numerical method for the solution of the complete convection–diffusion-reaction equation is derived by the use of finite differences. The numerical computation of the initial transient and the final periodic steady-state values is also discussed.     

塑料闪烁体的辐照特性

利用⁶⁰Co放射源分别对3种塑料闪烁体(BC-408, EJ-200, BC-404)进行辐照损伤研究, 比较辐照前后的透射谱、发射谱及光产额的变化, 发现3种闪烁体在低剂量具有较好的抗辐照性能; 当照射剂量超过1.44×10⁴Gy时,透射谱明显变坏, 光输出减少很严重, 但发射谱却保持不变.     

F+H2→HF+H反应的全量子态分辨的散射动力学研究

利用高灵敏度的氢原子里德堡飞渡时间谱方法研究了 F H_2→HF H 反应碰撞能在5.02kJ/mol 下的交叉分子束反应态态散射动力学.所有在时间飞渡谱中被观测到的谱峰可以归属为 HF 产物的振转态结构.还观测到了明显的 HF(v’=3)前向散射,以及少许的 HF(v’=2)前向散射.     

Time-Resolved Photoacoustic Calorimetry: From Carbenes to Proteins

Why have molecules only been seen but not heard? For over a century chemists have probed reactions with various spectroscopic methods to learn about structures, dynamics, and reactivities of their molecules. What they have not done is to listen to their molecules react. Although the photoacoustic phenomenon has been known since 1880, it is only in the last twenty years that technology has developed to the point where sound waves produced by reacting molecules can be time resolved and the information contained within the waves deciphered. The information content within the photoacoustic wave is indeed rich, for one can learn about the dynamics and the magnitude of enthalpy changes associated with the reaction as well as the changes in molecular volume. This review article chronicles the development of time-resolved photoacoustic calorimetry and its application to a variety of reactions encountered in organic and organometallic chemistry and biochemistry.     

2-Propanol oxidation on platinum and platinum–rhodium electrodeposits

The electrocatalytic oxidation of 2-propanol was investigated using on line differential electrochemical mass spectrometry (DEMS) on electrodeposited Pt and an arrange of bimetallics: Pt_0.84Rh_0.16, Pt_0.70Rh_0.30, Pt_0.55Rh_0.45. It has been observed that the Pt_0.84Rh_0.16 bimetallic electrode presented the best catalytic activity for 2-propanol electrochemical oxidation. Since 2-propanol is a secondary alcohol, only acetone and CO₂ are produced. The total yield of CO₂ and acetone has been determined from the DEMS measurements. It is found that acetone is the major product, as reported before for other electrodes. The acetone and CO₂ yield depends on the electrode composition. High amount of rhodium in the electrode composition strongly diminish the reaction rate as indicated by the decrease of both the acetone and CO₂ yield. However, acetone inhibition is much more intense. The only bimetallic electrode that presents considerable mass spectroscopy signals intensity for CO₂ and acetone is the Pt_0.84Rh_0.16 electrode. This electrode shows a slight increase in CO₂ selectivity, compared to the other electrodes studied in this work. Only very low coverages of stable adsorbates were present during the reaction. Two and one carbon adsorbate were observed for all the electrodes. Three carbon adsorbates were detected only for the Pt_0.84Rh_0.16 electrode. Therefore, acetone production does not require a stable adsorbate.