Non-universal critical behaviour of heteronuclear dimers on a square lattice––A Monte Carlo study

Monte Carlo simulation within the grand canonical ensemble, the histogram reweighting technique, and finite size scaling analysis are used to explore the phase behaviour of heteronuclear dimers, composed of A and B type atoms, on a square lattice. We have found that for the models with attractive BB and AB nearest-neighbour energy, u_BB=u_AB=−1, and for non-repulsive energy between AA nearest-neighbour sites, u_AA<0, the system belongs to the universality class of the two-dimensional Ising model. However, when u_AA>0, the system exhibits a non-universal critical behaviour. We have evaluated the dependences of the critical point characteristics on the value of u_AA.     

In situ neutron diffraction study (300-1273 K) of non-stoichiometric strontium ferrite SrFeOx

The high-temperature cubic phase of non-stoichiometric strontium ferrite SrFeO_x (2.5≤x≤3.0) has been studied by in situ neutron powder diffraction in air over the temperature range 300-1273 K. The composition of SrFeO_x changes within the range 2.56≤x≤2.81 from 1273 to 673 K, respectively.Rietveld refinements of the diffraction patterns show that the high-temperature cubic phase of SrFeO_x is consistent with a face-centred Fm3c structure. This structure leads to agreement with previous density measurements. This cell allows the high-temperature structure of SrFeO_x to be described in terms of a solid solution of the composition end members. Cubic SrFeO_x at high temperature is found to closely obey Vegard's law. The density of cubic SrFeO_x is also found to exhibit a linear relationship with composition.     

生长温度对碳纳米管阴极场发射性能的影响

碳纳米管(Carbon Nanotubes,CNTs)场发射平面显示器(Field Emission Display,FED)与其他显示器比较显示了其独特优点,被认为是未来理想的平面显示器之一。碳纳米管阴极作为器件的核心部分,其性能的好坏直接影响显示器的性能。针对30~60英寸(76.2~152.4cm)大屏幕显示器所用的厚膜工艺,即采用丝网印刷法制备了碳纳米管阴极阵列,研究了化学气相沉积法在不同温度下生长的CNTs的场发射电流-电压特性,找到了适合FED用碳纳米管的最佳生长温度。结果表明生长温度越高(750℃),CNTs场发射性能越好。并用荧光粉阳极测试这些CNTs的场发射发光显示效果,验证了上述结论。     

宽带膜厚实时监控过程中膜层折射率的确定方法

为了准确计算出镀膜过程中每层膜的折射率，介绍了实时监控过程中确定膜层折射率的2种方法：一种是由实测的透射比光谱直接反算出膜层的折射率；另一种是用最小二乘法的优化算法实时拟合折射率。试验结果表明：在线反算适合单点监控，所得折射率误差小于2%。然而在实际镀膜过程中,由于宽带内膜层参数误差较大,一般大于25%。为此，采用最小二乘法拟合，即在整个宽光谱范围内采集每个波长点的信息，所得结果误差很小，一般都在2％～5%之间,有时可达到10%,在很大程度上提高了实际镀膜时膜厚监控的精度。     

掺钕聚甲基丙烯酸甲酯的光学特性

研究了制备的掺钕螯合物Nd(DBM)3Phen材料的吸收光谱、激发光谱、荧光光谱,应用Judd-Ofelt理论计算了该材料的强度参量．分析了钕离子激发态4F3／2的辐射寿命(631 μs)和4F3／2→4IJ′跃迁的受激发射截面和荧光分支比．     

弱(L_1,L_2)-BLD映射的正则性

本文首先将文［１］中的ＢＬＤ映射推广为弱（Ｌ１，Ｌ２）－ＢＬＤ映射，并证明了如下正则性结果：存在两个可积指数 Ｐ１＝Ｐ１（ｎ，Ｌ１，Ｌ２）＜ｎ＜ｑ１＝ｑ１（ｎ，Ｌ１，Ｌ２），使得对任意弱（Ｌ１，Ｌ２）－ＢＬＤ映射ｆ∈（Ω，Ｒｎ），都有ｆ∈（Ω，Ｒｎ），即ｆ为（Ｌ１，Ｌ２）－ＢＬＤ映射．     

两种方法制备ITO薄膜的红外特性分析

比较了用电束加热蒸发法和直流磁控溅射法制备的氧化锡铟(ITO)薄膜在红外波段的光学特性实验发现,通过直流磁控溅射在常温下制备的ITO薄膜在红外波段折射率稳定、消光系数小,比电子束加热蒸发制备的膜有较高的透过率在波长1550nm附近的透过率可达86%以上,消光系数约为004,方电阻最低为100Ω/□.     

Asymptotique de la norme $L^2$ d'un cycle géodésique dans les revêtements de congruence d'une variété hyperbolique arithmétique

Let M be an arithmetic hyperbolic manifold and be a codimension 1 geodesic cycle. In this paper, we study the asymptotic growth of the -norm of the lifts of F in the congruence tower above M. We obtain an explicit value for the growth rate of this norm. In particular, we provide a new proof of a celebrated result of Millson [Mi] on the homology of the arithmetic hyperbolic manifolds. The method is quite general and gives a new way of getting non zero homology classes in certain locally symmetric spaces. Received: 20 April 2001; in final form: 26 September 2001 / Published online: 28 February 2002     

Biodegradable/biocompatible ABC triblock copolymer bearing hydroxyl groups in the middle block

New biodegradable/biocompatible ABC block copolymers, poly(ethylene oxide)‐b‐poly(glycidol)‐b‐poly(L ,L ‐lactide) (PEO‐PGly‐PLLA), were synthesized. First, PEO‐b‐poly(1‐ethoxyethylglycidol)‐b‐PLLA was synthesized by a successive anionic ring‐opening copolymerization of ethylene oxide, 1‐ethoxyethylglycidyl ether, and L ,L ‐lactide initiated with potassium 2‐methoxyethanolate. In the second step, the 1‐ethoxyethyl blocking groups of 1‐ethoxyethylglycidyl ether were removed at weakly acidic conditions leaving other blocks intact. The resulting copolymers were composed of hydrophilic and hydrophobic segments joined by short polyglycidol blocks with one hydroxyl group in each monomeric unit. These hydroxyl groups may be used for further copolymer transformations. The PEO‐PGly‐PLLA copolymers with a molecular weight of PLLA blocks below 5000 were water‐soluble. Above the critical micellar concentration (ranging from 0.05 to1.0 g/L, depending on the composition of copolymer), copolymers formed macromolecular micelles with a hydrophobic PLLA core and hydrophilic PEO shell. The diameters of the micelles were about 25 nm. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 3750–3760, 2003     

Active long pulse shaping technique of pulsed CO2 laser using multi-pulse discharge control

We describe the pulse forming of pulsed CO₂ laser using multi-pulse superposition technique. Various pulse shapes, high duty cycle pulse forming network (PFN) are constructed by time sequence. This study shows a technology that makes it possible to make various long pulse shapes by activating SCRs of three PFN modules consecutively at a desirable delay time with the aid of a PIC one-chip microprocessor. The power supply for this experiment consists of three PFN modules. Each PFN module uses a capacitor, a pulse forming inductor, a SCR, a high voltage pulse transformer, and a bridge rectifier on each transformer secondary. The PFN modules operate at low voltage by driving the primary of HV pulse transformer. The secondary of the transformer has a full-wave rectifier, which passes the pulse energy to the load in a continuous sequence.We investigated various long pulse shapes as different trigger time intervals of SCRs among three PFN modules. As a result, we could obtain laser beam with various pulse shapes and durations from about 250 to 1000 μs.