钯II催化CO/乙烯共聚加压原位红外光谱研究

聚酿以其优良的物理、化学性能及原料（CO乙烯）简单易得的优点，在世界范围内已引起人们的普遍关注．为寻找价廉的催化剂或改良高效或（11）一双磷催化剂以推动聚酮的工业化进程，必须对共聚机理进行深入的研究．S；，n［’，’1、DrentP］等人根据对产品主链和端基的分析首先     

溶液pH值对聚邻甲苯胺电化学性质的影响

本文报道了溶液pH值对聚邻甲本胺电化学性质的影响。研究结果表明,电化学合成的聚邻甲苯胺的循环伏安曲线、氧化电位、膜的颜色、充放电容量、紫外可见光谱以及氧化还原活性都受到溶液pH的影响。在低pH值的溶液中,随着扫描电位的变化,聚邻甲苯胺膜的颜色可逆地变化,而在pH4.13的溶液中进行扫描时,膜的颜色不变化,电化学活性也消失。     

聚电解质溶液中2.6-ANS探针的荧光谱研究

本文合成了2.6—ANS荧光探针分子,并在含有不同外加盐的NaPSS溶液中测定了探针的荧光发射光谱。结果表明:探针的荧光强度随Cs增大而增大,而探针光谱的最大发射波长和半波宽度随Cs增大而减小。当Cs达到一定值时,荧光谱参数与Cs关系曲线出现转折点,此时聚离了链以“类胶束”状态存在。     

Enhanced electrodeposition of indium hexacyanoferrate thin films through improved plating solution stability

An ordinary plating solution for indium hexacyanoferrate (InHCF) thin film deposition, mainly composed of equal concentrations of In³⁺ and [Fe(CN)₆]^3–, usually forms precipitates rapidly when either concentration is higher than few millimolar. This contributes to the plating solution's instability. Moreover, electrodeposited capacities are limited accordingly. In this work, the plating solution's stability and the electrodeposition of InHCF were greatly enhanced by adding a large amount of K⁺ and/or H⁺. It was found that a 10-mM plating solution added with 1 M HCl and 1 M KCl could be stored as fresh over a one-week period, whereas an unmodified plating solution became useless within a couple of minutes. Also, such cationic additions, especially adding H⁺, increased the electrodeposited capacity ca. 18 times at least, as compared with that obtained from the unmodified plating solution. Furthermore, related enhancing mechanisms were proposed and verified. To sum up, this study offers a means for better InHCF electrodeposition and should promote the applications of InHCF films. Electronic Publication     

克拉霉素漂浮-生物粘附微囊的制备及性能研究

选用乳化-溶剂挥发法制备乙基纤维素载药微球(EMs), 并通过内部凝胶化法进行包衣制得海藻酸钠-乙基纤维素载药微囊(AEMs), 最后通过离子交联法进一步包衣制得壳聚糖-海藻酸钠-乙基纤维素载药微囊(CAEMs). 研究克拉霉素漂浮\|生物粘附微囊的制备工艺, 并考察微囊的体外漂浮性能、 粘附性能及体内滞留性能. 结果表明, CAEMs球形度较好, 药物包封率为72.3%~78.2%, 载药量为7.1%~12.7%. 在pH=5的醋酸缓冲液中, 6 h时的累积释放率为56.6%~70.6%, 漂浮率大于70%, 4 h时的体内滞留率为60.5%. CAEMs有望通过延长药物胃内滞留时间, 在临床用于根除幽门螺旋杆菌, 从而降低消化道溃疡的复发率.     

在位分散聚合聚甲基丙烯酸甲酯/二氧化硅纳米复合材料研究

应用在位分散聚合方法制备了分散相粒径介于１３０ｎｍ左右的聚甲基丙烯酸甲酯／二氧化硅ＰＭＭＡ／ＳｉＯ２纳米复合材料，并利用ＳＥＭ，ＤＭＡ，ＴＧＡ等手段研究了该体系的性能．结果表明，经表面处理的ＳｉＯ２无机填料在复合材料基体中分散均匀，界面粘结好．ＳｉＯ２填充粒子的用量对基体的热稳定性，动态力学行为，光学行为以及拉伸强度，弹性模量，断裂伸长率等力学性能都有较大影响     

Analysis of citrates and benzoates used in poly(vinyl chloride) by supercritical fluid extraction and gas chromatography

Supercritical fluid extraction (SFE) has been demonstrated to be a useful tool in the determination of additives in polymeric materials. This paper describes the determination of some citrates and benzoates in poly(vinyl chloride) blended with 33–34% of plasticizer using off-line SFE followed by gas chromatography. Experimental factors affecting SFE have been studied by gravimetric analysis, followed by analysis of the extracts using a gas chromatograph equipped with a flame ionization detector. The extraction process is governed by the solubility of the plasticizers in the supercritical fluid or by their diffusion through the polymer matrix, which depend on the pressure and temperature used. Maximum extraction (>99%) is obtained at pressures and temperatures higher than 40 MPa and 80 °C, respectively. Due to purge losses, the collection efficiency of plasticizers into a liquid solvent ranges from 85 to 90%. The applicability of the SFE method is demonstrated using real samples and comparing the results with those obtained by conventional Soxhlet extraction.     

氟化γ-Al2O3表面酸性的NMR和FTIR表征

用红外光谱和核磁共振技术研究了氟化作用对γ-Al2O3的表面酸性（酸中心类型、强度及数量）的影响。吡啶和二甲基吡啶在氟化γ-Al2O3（F／γ-Al2O3）表面上吸－脱附的IR光谱和三甲基膦在F／γ-Al2O3表面上吸附的^31P MAS NMR结果表明，F／γ-Al2O3表面上既存在Lewis酸位又存在Broensted酸位。L酸的总量随氟含量的增加而减少。但其强度随之增加，且同时产生几种新的L酸位。B酸的数量和强度在样品含氟量为2％－3％间存在极大值。研究还表明，三甲基膦是一种测量F／γ-Al2O3表面酸性的灵敏的NMR探针分子，^31P MAS NMR和红外光谱的测试结果基本一致。同时，对氟化过程中酸位形成和变化机理进行了探讨。     

Preparation of flame retardant polyamide 6 composite with melamine cyanurate nanoparticles in situ formed in extrusion process

This paper is focused on in situ preparation of melamine cyanurate (MCA) nanoparticles from reaction of melamine (MEL) and cyanuric acid (CA) and their flame retardant polyamide 6 (PA6) composite in the extrusion process through a novel reactive processing method. Fourier transform infrared (FT-IR), X-ray diffraction (XRD), differential scanning calorimetry (DSC), thermogravimetric analysis (TGA) and scanning electron microscopy (SEM) were utilized to characterize the in situ formed MCA nanoparticles and their blends with PA6. Introduction of pentaerythritol (LTP) and water-bound plasticizer dioctyl phthalate (DPT) into the extrusion reaction system greatly inhibits the evaporation of water required for melamine and cyanuric acid reaction at high temperature (higher than 180 °C), laying a foundation for successful in situ preparation of MCA through reactive processing. XRD and FT-IR measurements indicate that under the effect of pentaerythritol, dioctyl phthalate and water, melamine really reacts with cyanuric acid to in situ form MCA in extrusion process. The reaction degree is close to 100%. A very important finding through SEM is that the in situ formed MCA particles, which were found to have aspect ratio of about 7.5, radial size in the range of 70-300 nm (mostly 70-90 nm) and crystallite size of less than 22 nm, are uniformly dispersed in the matrix PA6 at nanoscale. The in situ formed MCA nanoparticles greatly improve the flame retardancy and the mechanical properties of flame-retarded PA6 materials, and the introduced plasticizer dioctyl phthalate also ameliorates the related impact property. The obtained flame-retarded PA6 materials have good comprehensive performance with flame retardancy UL-94 V-0 rating at 1.6 and 3.2 mm thickness, tensile strength 48.0 MPa, elongation at break 106.3% and Izod notched impact strength 8.92 kJ/m². Compared with flame-retarded PA6 material with in situ formed MCA, the one prepared through conventional blending of PA6 with commercial MCA product has improved tensile strength but deteriorated impact strength and flame retardancy.     

Structure of thiocyanate adlayers on Rh(111): an in situ STM study

In situ scanning tunneling microscopy (STM) was used to examine the structure of thiocyanate adlayers specifically adsorbed on Rh(111) in solutions of potassium hydroxide and perchloric acid, both containing potassium thiocyanate (KSCN). An atomically flat terrace-step structure was consistently observed on Rh(111) surfaces prepared by the flame-annealing-quenching method. The Rh(111)-(1 × 1) atomic structure was discerned on the atomically flat terrace even in the alkaline solution. High-resolution STM images disclosed two different structures of the SCN⁻ adlayers, () and (2 × 2), in the alkaline and the acidic media, respectively. In each structure, an individual adsorbed SCN⁻ ion appeared as a single spot with a constant corrugation height in STM images, suggesting that SCN⁻ ions adsorbed predominantly with their S-ends at particular bonding sites on Rh(111). The difference in the adlayer structure in the two solutions can be attributed to the interaction between adsorbed SCN⁻ and coadsorbed K⁺ in the alkaline solution, and is different from that between adsorbed SCN⁻ and H⁺ in the acidic solution. Received: 26 February 1997 / Accepted: 3 March 1997