Nickel coated on beech wood by electroless nickel coating: effects of complexing agent concentrations on nickel film properties

In order to obtain beech wood substrates with new functions as conductive materials and to develop their utilities in industrial fields, the technique of electroless nickel coating on the beech wood substrate was employed. The influence of complexing agent concentration [Na₂EDTA·2H₂O] on the nickel surface resistivity was studied. The process conditions were Ni(CH₃COO)₂·4H₂O 0.103?mol/L, CH₃CHOCOOH 18.18?mL/L, N₂H₅OH 54.54?mL/L, NaOH 0.193?mol/L, pH value of 9.5, temperature of 75?°C, and the complexing agent concentration varied between 0.012 and 0.061?mol/L. By means of XRD, EDXRF, and SEM, the chemical composition and morphology of the prepared films were investigated. The results showed that when the complexing agent concentration increased from 0.012 to 0.061?mol/L in the electroless nickel coating baths, the gained nickel mass on the beech wood substrate decreased from 17.04 to 9.03?mg/cm², the nickel crystallite sizes reduced from 16.1 to 1.41?nm and the electric measurements demonstrated that the nickel surface resistivity rose from 0.004 to 192.16?kΩ/cm².     

Bonding at Compatible and Incompatible Amorphous Interfaces of Polystyrene and Poly(Methyl Methacrylate) Below the Glass Transition Temperature

Abstract

Films of high‐molecular‐weight amorphous polystyrene (PS, M _w = 225 kg/mol, M _w/M _n = 3, T _g‐bulk = 97°C, where T _g‐bulk is the glass transition temperature of the bulk sample) and poly(methyl methacrylate) (PMMA, M _w = 87 kg/mol, M _w/M _n = 2, T _g‐bulk = 109°C) were brought into contact in a lap‐shear joint geometry at a constant healing temperature T _h, between 44°C and 114°C, for 1 or 24 hr and submitted to tensile loading on an Instron tester at ambient temperature. The development of the lap‐shear strength σ at an incompatible PS–PMMA interface has been followed in regard to those at compatible PS–PS and PMMA–PMMA interfaces. The values of strength for the incompatible PS–PMMA and compatible PMMA–PMMA interfaces were found to be close, both being smaller by a factor of 2 to 3 than the values of σ for the PS–PS interface developed after healing at the same conditions. This observation suggests that the development of the interfacial structure at the PS–PMMA interface is controlled by the slow component, i.e., PMMA. Bonding at the three interfaces investigated was mechanically detected after healing for 24 hr at T _h = 44°C, i.e., well below T _g‐bulks of PS and PMMA, with the observation of very close values of the lap‐shear strength for the three interfaces considered, 0.11–0.13 MPa. This result indicates that the incompatibility between the chain segments of PS and PMMA plays a negligible negative role in the interfacial bonding well below T _g‐bulk.     

Static and time-dependent properties of polymer gels around the volume phase transition

Recent progress in the study of the volume phase transition of polymer gels is reviewed. The phenomenological theories of swelling equilibrium and phase transition of gels are summarized, and some basic experimental results on poly-N-isopropylacrylamide (NIPA) gels are compared with the prediction from these theories. Special attention is paid to the elastic properties of the gel network near the volume phase transition. The effect of external stresses on the swelling and the phase transition is analyzed. Some anomalous and unique characteristics revealed in NIPA gels such as shape- and size-dependent swelling and phase transition properties, curious phase coexistence, and domain structure are presented. Experimental results on some time-dependent phenomena such as phase separation, spinodal decomposition, and pattern formation are also presented and discussed. Some problems inherent to gels from biological bodies are briefly discussed.     

Strongly localized states in a single carbon nanotube with polymer molecules

A single-walled carbon nanotube (SWCNT) with conjugated polymer molecules is analyzed via optical spectroscopy. The presence of strongly localized excitonic states in the SWCNT is confirmed using time-integrated photoluminescence (PL). The PL spectrum exhibits extremely narrow width (~0.8 meV) which is attributed to the strong confinement of the states by polymer molecules. In addition, I observed that the excited states are gradually filled as a function of the excitation power, which supports the localized excitonic behavior. Only the ground excitonic state is observed at low excitation powers, but three additional PL peaks appear as the excitation power is increased. Especially, the power-dependent PL spectrum shows a blueshift and increased width, which can be elucidated in terms of quantum confined stark effect and the screening of induced electric fields. Overall, I demonstrate that the presence of polymer molecules induces several localized states in a single SWCNT.     

Restoration of universality for the rod-to-coil transition scaling in the infinite-dimensionality limit: Exact results for directed walks

We derive scaling forms for the thermodynamic and correlation quantities for the turn-weighted fully and partially directed self-avoiding walks on the hypercubic lattices ind2. In the grand canonical (fixed fugacity per step) ensemble, the conformational rod-to-coil transition sets up in the regimew¯N=O(1), wherew is the weight of each 90° turn and¯N is the (fugacity-dependent) average number of steps. Contrary to the conventional critical phenomena wisdom, the scaling functions for the two different walk models, directed and partially directed, become universal only in the limitd.     

A three-parameter model describing the experimental relation between shear stress and shear rate for laminar flow of aqueous polymer solutions

Summary A three-parameter model is introduced to describe the shear rate — shear stress relation for dilute aqueous solutions of polyacrylamide (Separan AP-30) or polyethylenoxide (Polyox WSR-301) in the concentration range 50 wppm – 10,000 wppm. Solutions of both polymers show for a similar rheological behaviour. This behaviour can be described by an equation having three parameters i.e. zero-shear viscosity ₀, infinite-shear viscosity , and yield stress ₀, each depending on the polymer concentration. A good agreement is found between the values calculated with this three-parameter model and the experimental results obtained with a cone-and-plate rheogoniometer and those determined with a capillary-tube rheometer.

---

Zusammenfassung Der Zusammenhang zwischen Schubspannung und Schergeschwindigkeit von strukturviskosen Flüssigkeiten wird durch ein Modell mit drei Parametern beschrieben. Mit verdünnten wäßrigen Polyacrylamid-(Separan AP-30) sowie Polyäthylenoxidlösungen (Polyox WSR-301) wird das Modell experimentell geprüft. Beide Polymerlösungen zeigen im untersuchten Schergeschwindigkeitsbereich von ein ähnliches rheologisches Verhalten. Dieses Verhalten kann mit drei konzentrationsabhängigen Größen, nämlich einer Null-Viskosität ₀, einer Grenz-Viskosität und einer Fließgrenze ₀ beschrieben werden. Die Ergebnisse von Experimenten mit einem Kegel-Platte-Rheogoniometer sowie einem Kapillarviskosimeter sind in guter Übereinstimmung mit den Werten, die mit dem Drei-Parameter-Modell berechnet worden sind.

---

a Pa^–1 physical quantity defined by:a = {1 – ( / ₀)}/ ₀ - c l concentration (wppm) - D m capillary diameter - L m length of capillary tube - P Pa pressure drop - R m radius of capillary tube - u m s^–1 average velocity - v _r m s^–1 local axial velocity at a distancer from the axis of the tube - shear rate (–dv _r /dr) - local shear rate in capillary flow - s^–1 wall shear rate in capillary flow - Pa s dynamic viscosity - _a Pa s apparent viscosity defined by eq. [2] - ( _a ) Pa s apparent viscosity in capillary tube at a distanceR from the axis - ₀ Pa s zero-shear viscosity defined by eq. [4] - Pa s infinite-shear viscosity defined by eq. [5] - l ratior/R - kg m^– density - Pa shear stress - ₀ Pa yield stress - _r Pa local shear stress in capillary flow - _R Pa wall shear stress in capillary flow _R = (PR/2L) - _v m³ s^–1 volume rate of flow With 8 figures and 1 table     

The rheology of suspensions of vinylon fibers in polymer liquids. II. Suspensions in polymer solutions

Summary The rheological properties of vinylon fiber suspensions in polymer solutions were studied in steady shear flow. Shear viscosity, first normal-stress difference, yield stress, relative viscosity, and other properties were discussed. Three kinds of flexible vinylon fibers of uniform length and three kinds of polymer solutions as mediums which exhibited remarkable non-Newtonian behaviors were employed. The shear viscosity and relative viscosity ( _r ) increased with the fiber content and the aspect ratio, and depended upon the shear rate. Shear rate dependence of _r was found only in the low shear rate region. This result was different from that of vinylon fiber suspensions in Newtonian fluids. The first normal-stress difference increased at first slightly with increasing fiber content but rather decreased and showed lower values for high content suspensions than that of the medium. A yield stress could be determined by using a modified equation of Casson type. The flow properties of the fiber suspensions depended on the viscosity of the medium in the suspensions under consideration.With 16 figures and 1 table     

On the theory of the condensed states of heteropolymers

The collapse (globulization) of an ideal heteropolymer chain under the action of an external attractive field is considered. The problem of the collapse of different types of primary structures, including mobile, periodic, large-block, and statistical structures, is formulated. It is shown that for a random heteropolymer, the mathematical image of the globular state is the chain-length independence of the probability distribution of a random thermal distribution function of the end monomer coordinates. The free energy per monomer of a chain in a globular state and local densities of monomers of all types are shown to be a self-averaging quantities. An exactly solvable model is proposed for a globule formed by a statistical heteropolymer chain. In this model, different types of monomers are attracted to different centers by linear elastic forces with identical elastic constants. The modulus of elasticity is obtained for a heteropolymer globule with respect to the attraction of different types of monomers in different directions. It is shown that this modulus is higher for a short-periodic polymer than for a statistical one.     

双涂层光纤应变传感器的理论与实验研究

对带有聚合物涂敷层和缓冲层的光纤应变传感器的力学特性进行了研究,建立了双涂层光纤与基体材料相互作用的线弹性理论模型.理论研究表明：在小半径近似条件下,双涂层光纤的力学传递特性决定于涂覆层和缓冲层的弹性模量的相对值;当缓冲层的弹性模量远大于涂覆层时,其作用可忽略.实验中,将光纤传感器埋入基体材料内部,利用白光干涉应变测量方法,对平均应变传递系数进行了实验研究.实验结果与理论仿真具有较好的一致性.     

Fabrication of polymer compound microlens by lens-on-lens microstructures

We proposed a novel method for fabricating polymer compound microlenses (PCMLs) using micro-inkjet technique and subsequent curing process. Two different types of PCMLs with sandwich microstructure (PDMS-Glycerol-PDMS), concave and convex PCMLs, have been designed and fabricated in experiments. Convex PCML has two real images and two foci. The concave PCML has one real and one virtual focal planes, which can generate one real image and one virtual image respectively. Moreover, the diameter of concave PCML can be controlled by adjusting the curing time and temperature. The proposed method is simple, efficient and suitable for realizing large-scale high numerical aperture PCMLs array, which has potential applications in diverse optical systems such as optical storage and three-dimensional imaging.