一种基于激光直写的水浊度传感结构

提出并制作了一种基于激光照射改变折射率方法的光度比浊度传感单元,综合了导波光学及检测相关知识原理.以UV光敏树脂为基底材料,采用“气体干法”除胶及分步固化的方法获得了该芯片化结构.传感器整个制作过程仅仅需要7~8 min因而使本方法具有很高的效率.由直写成型的单元组建传感系统对标准悬浊液样品进行了实验测试,所得的相关数据在SISO算法神经元网络系统中进行处理,获得了传感器浊度与对应散射系数的关系曲线.通过试剂检验的方法得知实际相对误差在5%左右.     

低串扰聚合物交叉耦合串联五环谐振电光开关(英文)

利用两组串联五环谐振器以及它们与两信道波导的交叉耦合作用,优化设计并模拟了一种超低串扰2×2新型聚合物电光开关.为了表征器件的输出光功率特性,给出了器件结构、分析理论和相关公式.为了在下行端口(drop端口)得到箱型光谱响应以及极低的串扰和插入损耗,优化了微环谐振级数和耦合间距.对器件输出光功率和输出光谱的模拟分析结果显示,器件交叉和直通态间的切换电压为4V,交叉和直通态下两端口间的串扰分别为-66dB和-54.7dB,插入损耗分别为2.34dB和0.24dB.在1GHz方波信号作用下,器件drop端口的上升和下降时间分别为15ps和90ps.由于聚合物微环的弯曲半径仅为19.45μm,因此该器件具有超紧凑的尺寸,其长度和宽度仅为0.407mm,约为马赫-曾德尔干涉仪或者定向耦合器等一般结构聚合物电光开关长度的1/10.依赖于小的封装尺寸和极低的串扰,该器件可以高密度地集成在光电子芯片上,在光片上网络中光信号的控制方面具有潜在的应用.     

Band bending at the conducting polymer/indium tin oxide interfaces with and without ultraviolet treatment

In this study, the effect of ultraviolet treatment on the band bending at the poly(3,4-ethylenedioxythiophene) doped with poly(4-styrenesulfonate)/indium tin oxide (PEDOT:PSS/ITO) interfaces were researched. The authors suggested that ultraviolet treatment could lead to a reduction in the band bending at the PEDOT:PSS/ITO interface, owing to the removal of carbon contamination at the ITO surfaces and a decrease in the number of the trap-states at the PEDOT:PSS/ITO interface.     

A study on wear resistance and microcrack of the Ti3Al/TiAl + TiC ceramic layer deposited by laser cladding on Ti-6Al-4V alloy

Laser cladding of the Al + TiC alloy powder on Ti-6Al-4V alloy can form the Ti₃Al/TiAl + TiC ceramic layer. In this study, TiC particle-dispersed Ti₃Al/TiAl matrix ceramic layer on the Ti-6Al-4V alloy by laser cladding has been researched by means of X-ray diffraction, scanning electron microscope, electron probe micro-analyzer, energy dispersive spectrometer. The main difference from the earlier reports is that Ti₃Al/TiAl has been chosen as the matrix of the composite coating. The wear resistance of the Al + 30 wt.% TiC and the Al + 40 wt.% TiC cladding layer was approximately 2 times greater than that of the Ti-6Al-4V substrate due to the reinforcement of the Ti₃Al/TiAl + TiC hard phases. However, when the TiC mass percent was above 40 wt.%, the thermal stress value was greater than the materials yield strength limit in the ceramic layer, the microcrack was present and its wear resistance decreased.     

Co50Fe25-xMnxSi25系列合金的结构、磁性和半金属性研究

利用实验和能带计算相结合的方法,对介于两种预期的半金属Heusler合金Co₂FeSi和Co₂MnSi间的四元合金Co₅₀Fe_25-xMn_xSi₂₅的晶体结构、磁性、能带结构和半金属性进行了研究.采用考虑库仑相互作用的的广义梯度近似方法计算了系列合金的能带结构,通过与实验结果进行对比,揭示了成分变化过程中合金分子磁矩及原子磁矩的变化规律.研究发现, 关键词： 磁性 半金属 Heusler合金     

Image analysis of atmospheric corrosion of field exposure high strength aluminium alloys

The corrosion morphology image acquisition system which can be used in the field was established. In Beijing atmospheric corrosion exposure station, the image acquisition system was used to capture the early stage corrosion morphology of five types of high strength aluminium alloy specimens. After the denoise treatment, wavelet-based image analysis method was applied to decompose the improved images and energies of sub-images were extracted as character information. Based on the variation of image energy values, the corrosion degree of aluminium alloy specimens was qualitatively and quantitatively analyzed. The conclusion was basically identical with the result based on the corrosion weight loss. This method is supposed to be effective to analysis and quantify the corrosion damage from image of field exposure aluminium alloy specimens.     

Microstructure and magnetic properties of Ni-rich Ni54Mn25.7Ga20.3 ferromagnetic shape memory alloy thin film

A Ni₅₄Mn_25.7Ga_20.3 ferromagnetic shape memory alloy thin film has been fabricated by using the RF magnetron-sputtering technique. The structure and magnetic properties of the film were systematically investigated. The results show that the film is in ferromagnetic martensite state at room temperature with the Curie temperature (T_c) of about 370 K. The saturation magnetization (M_s) of the film reaches 45 emu/g at 300 K, which is about 80% as large as that of Ni–Mn–Ga bulk material. The magnetization hysteresis loops significantly depend on temperatures. The residual magnetization (M_r) and the coercive force (H_c) increase with decreasing temperatures. The grains homogeneously distribute in the film. The microstructure of the film consists of martensite plates. The interface between the martensite variants is clear and straight, indicating a good mobility.     

Atomic short-range order in CuMn alloys

The establishment of atomic short-range order (SRO) has been investigated in CuMn alloys (5, 8,13,16,20 at. % Mn) by measurement of the electrical resistivity during isochronal and isothermal annealing. An increasing degree of SRO is accompanied by a reduction of resistivity; this effect increases with Mn concentration. For 8,13 and 16 at. % Mn SRO kinetics turn out to deviate significantly from single exponential behavior with a maximum at 13 at. % Mn, whereas at 5 and 20 at. % Mn SRO is adjusted in a single exponential process. For data analysis three methods are used: a sum of two and three exponentials as well as a log-normal spectrum of relaxation times. The strong interaction between second-nearest-neighbor atoms in CuMn seems to be essential for SRO kinetics but of minor importance for the value of SRO-induced resistivity change.     

On the theory of the condensed states of heteropolymers

The collapse (globulization) of an ideal heteropolymer chain under the action of an external attractive field is considered. The problem of the collapse of different types of primary structures, including mobile, periodic, large-block, and statistical structures, is formulated. It is shown that for a random heteropolymer, the mathematical image of the globular state is the chain-length independence of the probability distribution of a random thermal distribution function of the end monomer coordinates. The free energy per monomer of a chain in a globular state and local densities of monomers of all types are shown to be a self-averaging quantities. An exactly solvable model is proposed for a globule formed by a statistical heteropolymer chain. In this model, different types of monomers are attracted to different centers by linear elastic forces with identical elastic constants. The modulus of elasticity is obtained for a heteropolymer globule with respect to the attraction of different types of monomers in different directions. It is shown that this modulus is higher for a short-periodic polymer than for a statistical one.     

A three-parameter model describing the experimental relation between shear stress and shear rate for laminar flow of aqueous polymer solutions

Summary A three-parameter model is introduced to describe the shear rate — shear stress relation for dilute aqueous solutions of polyacrylamide (Separan AP-30) or polyethylenoxide (Polyox WSR-301) in the concentration range 50 wppm – 10,000 wppm. Solutions of both polymers show for a similar rheological behaviour. This behaviour can be described by an equation having three parameters i.e. zero-shear viscosity ₀, infinite-shear viscosity , and yield stress ₀, each depending on the polymer concentration. A good agreement is found between the values calculated with this three-parameter model and the experimental results obtained with a cone-and-plate rheogoniometer and those determined with a capillary-tube rheometer.

---

Zusammenfassung Der Zusammenhang zwischen Schubspannung und Schergeschwindigkeit von strukturviskosen Flüssigkeiten wird durch ein Modell mit drei Parametern beschrieben. Mit verdünnten wäßrigen Polyacrylamid-(Separan AP-30) sowie Polyäthylenoxidlösungen (Polyox WSR-301) wird das Modell experimentell geprüft. Beide Polymerlösungen zeigen im untersuchten Schergeschwindigkeitsbereich von ein ähnliches rheologisches Verhalten. Dieses Verhalten kann mit drei konzentrationsabhängigen Größen, nämlich einer Null-Viskosität ₀, einer Grenz-Viskosität und einer Fließgrenze ₀ beschrieben werden. Die Ergebnisse von Experimenten mit einem Kegel-Platte-Rheogoniometer sowie einem Kapillarviskosimeter sind in guter Übereinstimmung mit den Werten, die mit dem Drei-Parameter-Modell berechnet worden sind.

---

a Pa^–1 physical quantity defined by:a = {1 – ( / ₀)}/ ₀ - c l concentration (wppm) - D m capillary diameter - L m length of capillary tube - P Pa pressure drop - R m radius of capillary tube - u m s^–1 average velocity - v _r m s^–1 local axial velocity at a distancer from the axis of the tube - shear rate (–dv _r /dr) - local shear rate in capillary flow - s^–1 wall shear rate in capillary flow - Pa s dynamic viscosity - _a Pa s apparent viscosity defined by eq. [2] - ( _a ) Pa s apparent viscosity in capillary tube at a distanceR from the axis - ₀ Pa s zero-shear viscosity defined by eq. [4] - Pa s infinite-shear viscosity defined by eq. [5] - l ratior/R - kg m^– density - Pa shear stress - ₀ Pa yield stress - _r Pa local shear stress in capillary flow - _R Pa wall shear stress in capillary flow _R = (PR/2L) - _v m³ s^–1 volume rate of flow With 8 figures and 1 table