Modification of Carbon Paste Electrode Based on Molecularly Imprinted Polymer for Electrochemical Determination of Diazinon in Biological and Environmental Samples

The wide use of pesticides can lead to environmental and human adverse effects. Diazinon, as an organophosphorous pesticide, is used in agriculture because of its low cost and high efficiency on insects. Due to the increasing application of pesticides, accurate analytical methods are necessary. The aim of this work was modification of carbon paste electrode composition and applying it as a sensor for determination of diazinon in biological and environmental samples. Multi‐walls carbon nanotubes and a molecularly imprinted polymer were used as modifiers in the sensor composition. A molecularly imprinted polymer and a non‐imprinted polymer were synthesized for applying in the electrode. After optimization of electrode composition, it was used to determine the analyte concentration. Instrumental parameters affecting the square wave voltammetric response were adjusted to obtain the highest current intensity. The modified electrode with MIP showed very high recognition ability compared to the electrode containing NIP. The obtained linear range was 5×10⁻¹⁰ to 1×10⁻⁶ mol L⁻¹. The detection limit of the sensor was 1.3×10⁻¹⁰ mol L⁻¹ and the relative standard deviation for analysis of target molecule by the proposed sensor was 2.87 %. This sensor was used to determine the diazinon in real samples (human urine, tap, and river water samples) without special sample preparation before analysis. The optimization of electrode composition containing mentioned modifiers improved its response considerably.     

Ammonium Determination in Water Samples by Using Opa-Nac Reagent: A Comparative Study with Nessler and Ammonium Selective Electrode Methods

A selective and sensitive method based on the ammonium derivatisation with o -phthaldialdehyde (OPA) and N -acetyl-cysteine (NAC) has been developed for ammonium determination in real water samples. The proposed procedure has been compared with ammonium reference methods such as Nessler reagent method and ammonium selective electrode. All procedures have been chemometrically tested and compared in terms of the main analytical properties. These procedures have been used to determine ammonium in unknown water samples. The OPA-NAC reagent method does not present any systematic error (proportional or constant), while Nessler reagent presents both of them for some samples assayed. The ammonium selective electrode is free of corrigible systematic errors, however presents amine interference. The OPA-NAC ammonium method is able to achieve a detection limit (LOD) of 0.07 mg/L in the sample, with a linear dynamic range up to 1.4 mg/L of ammonium.     

Practical Study into Enhancing IgG Immobilisation on Screen-Printed Electrodes for Environmental Applications

This work is focused on the influence of pH and applied potential for the immobilisation of rabbit IgG on a carbon screen-printed electrode. The orientation of IgG molecule at the surface is fundamental for activity and reproducibility of the immunosensor. As the electrode potential is increased a particular order may be brought to the immobilised antibodies, i.e. the antibodies adapt a more favourable arrangement on the surface to facilitate better binding. The response increased when changing the pH from basic to acidic medium and the reverse trend was observed for the limit of detection (LOD). When a potential was applied to the electrode, the response generally decreased and the LOD increased in the order acidic > basic > neutral pH. The LODs obtained from antibodies immobilised at acidic pH and + 100 mV were better than the LODs obtained at other conditions.     

聚吡咯/海藻酸钠纳米球的制备及其应用于高性能超级电容器

用海藻酸钠作为结构导向剂,通过原位氧化聚合吡咯法制备了聚吡咯/海藻酸钠(PPy/SA)纳米球.聚吡咯/海藻酸钠纳米球的形貌和结构通过扫描电镜(SEM)、X射线衍射(XRD)和傅里叶变换红外(FTIR)光谱进行表征.材料的电化学性能通过循环伏安法和恒电流充放电方法进行测试.电化学测试表明,聚吡咯/海藻酸钠纳米球在1 mol L-1KCl电解液中,电流密度为1 A g-1时其比电容高达347 F g-1.与纯聚吡咯相比较,聚吡咯/海藻酸钠纳米球具有更优异的循环稳定性能.     

Transition metals on the (0 0 0 1) surface of graphite: Fundamental aspects of adsorption,diffusion, and morphology

In this article, we review basic information about the interaction of transition metal atoms with the (0 0 0 1) surface of graphite, especially fundamental phenomena related to growth. Those phenomena involve adatom-surface bonding, diffusion, morphology of metal clusters, interactions with steps and sputter-induced defects, condensation, and desorption. General traits emerge which have not been summarized previously. Some of these features are rather surprising when compared with metal-on-metal adsorption and growth. Opportunities for future work are pointed out.     

聚四氟乙烯和石墨对聚醚酰亚胺摩擦学性能的影响

将聚四氟乙烯(PTFE)和石墨两类减摩耐磨填料填充到聚醚酰亚胺(PEI)中,表征其摩擦性能,利用扫描电子显微镜分析了磨损表面的显微结构,并分析了磨损机制.研究结果表明,PTFE和石墨的填充明显改善了PEI的摩擦磨损性,摩擦系数降低到0.3以下(纯PEI的摩擦系数为0.41),磨损率降低了3个数量级.在PTFE体系中,PTFE质量分数为10%时,PEI基共混材料的摩擦系数最低为0.23;而在质量分数为15%的石墨体系中,PEI基共混材料摩擦系数最低为0.27.磨损率随着填料含量的增加而逐渐下降,在填料质量分数为20%之后,摩损率下降平缓.因此PTFE和石墨的填充对PEI的摩擦学性能起到了很好的改善作用,而且PTFE比石墨的改善效果更优益.共混物的机械性能测试结果表明,在填料质量分数为5%~15%时,共混物具有良好的机械性能.     

(PtAuPt)HN/GC的制备及对甲酸氧化的电催化性能

以Se溶胶为模板,合成了多层核壳结构的Se@Pt@Au@Pt实心纳米粒子;采用化学与电化学相结合的除硒方法制得了(PtAuPt)HN/GC,并表征了(PtAuPt-Se)HN的表面形貌、结构与组成;以甲酸为探针分子,比较了(PtAuPt)HN/GC和Pt/C/GC对甲酸氧化的电催化行为,发现(PtAuPt)HN/GC催化甲酸氧化只有1个氧化峰,峰电位和峰电流分别约为0.35V和1.22mA/cm2,而Pt/C/GC则有2个氧化峰,在0.35V时所对应的电流密度仅约为0.30mA/cm2,前者在该电位时的电流密度是后者的4倍;在0.30mA/cm2的电流密度下,(PtAuPt)HN/GC对应的电极电位为0.01V,比Pt/C/GC负移了340mV;在600s时的计时电流分别为0.06和0.02mA/cm2.(PtAuPt)HN对甲酸氧化的电催化活性不但比Pt/C高,而且具有一定的抗CO中毒性能.     

Preparation and properties of ZnMoO4 anode materials with polymer network gel method

Polymer network gel method combines the advantages of solid-phase method and liquid phase method, triggering acrylamide (AM) radical polymerization in aqueous solution and N, N′- methylene bis acrylamide (MBAM) active double bond cross-linking reaction, forming polymer chains to form a three-dimensional network. The polymer network space formed by the gel is bound and evenly distributed to the ions in the solution, thereby reducing the contact and aggregation of molecules and achieving the purpose of uniform particle size and small particle size. The principle diagram of network gel is shown in Figure. Using cubic zinc acetate and ammonium molybdate tetrahydrate as raw materials, cubic ZnMoO₄ negative electrode materials were prepared with polymer network gel method. The polymer network gel method has various effects on the structure, morphology and electrochemical properties of materials. Besides, the calcination temperature and calcination time were also the key factors to the electrochemical properties of the materials. In this paper, the effects of the ratio of monomer and crosslinker, calcination temperature and calcination time on ZnMoO₄ materials were studied by single variable method, the preparation process was optimized, and its characterization and electrochemical tests were carried out. After 100 cycles, the optimized ZnMoO₄ electrode has a discharge capacity of 374.0 mAh· g^?1, 332.5, 263.5 and 177.1 mAh · g^?1 at current densities of 0.1, 0.5, 1.0 and 2.0 A g^?1, respectively. The electrochemical results show that the optimized ZnMoO₄ has high capacity, large rate capability and excellent cycle stability.     

Flexible carbon membrane supercapacitor based on γ-cyclodextrin-MOF

Supercapacitors (SCs) with high energy density and power density are a research hotspot. Herein, we report a flexible porous carbon membrane supercapacitor prepared by electrospinning polyacrylonitrile (PAN) with γ-cyclodextrin-MOF (γ-CD-MOF) and then carbonizing at 900 °C. BET results showed that the supercapacitor retained the skeleton of γ-CD, γ-CD-MOF and the pores formed by the spun-fibers, which were 0.73, 1.09 and 23–186 nm, respectively, showing a high specific surface area of 134.7 m²/g. The hierarchically porous structures ensure rapid charge transfer and ion diffusion, resulting in the PAN/γ-CD-MOF carbon electrode with a high capacity of 283.3 F/g. Moreover, the supercapacitor had a high energy density up to 17.5 Wh/kg and power density up to 6 kW/kg. Significantly, it showed excellent cycle stability with a capacitance retention of 97.5% after 6000 cycles. This work provides a supramolecular strategy to construct a flexible porous carbon membrane, which has potential for supercapacitor applications.     

Sensitive Determination of 17β-Estradiol using a Magneto Sensor Based on Magnetic Molecularly Imprinted Polymer

The analysis of 17β-estradiol with high sensitivity and selectivity is extremely relevant to control the impacts that this compound can cause on health and the environment. Thus, we describe the development and application of a magneto carbon paste electrode based on magnetic molecularly imprinted polymer (MCPE-MMIP) for determination of 17β-estradiol. The analyte adsorbed on the MMIP was immobilized on the electrode surface by magnetic capture. The morphological and structural characterization of the obtained MMIP suggests that the material was effectively synthesized. MCPE-MMIP showed an improvement in the sensitivity for 17β-estradiol detection when compared to electrode configurations in the absence of this material. The optimum conditions (0.10 mol L⁻¹ phosphate buffer pH 7.0) were reached by differential pulse adsorptive stripping voltammetry (DPAdSV), in which the method presented linearity ranged from 0.06 to 175 μmol L⁻¹ with limits of detection and quantification of 0.02 and 0.06 μmol L⁻¹, respectively. The proposed sensor was applied effectively in the analysis of 17β-estradiol in river water and raw milk samples, exhibiting excellent recovery values (between 96.20 and 104 %), which were confirmed by HPLC analysis.