Lead Sensor Using Gold Nanostructured Screen‐Printed Carbon Electrodes as Transducers

Gold nanostructured screen‐printed carbon electrodes are demonstrated to be suitable transducers for the determination of lead using square‐wave voltammetry. Reproducible gold nanostructures have been obtained by direct electrochemical deposition. A calibration plot from 2.5 to 250 μg/L was obtained in acidic solutions of Pb(II) with a reproducibility of 4% (n=10). The detection limit was 0.09 μg/L of lead. The method is then applied to perform a blood lead analysis by adjusting square‐wave parameters in capillary or venous blood with a minimum sample pretreatment and excellent accuracy and reproducibility.     

Classification Performance of a Low Pressure Differential Mobility Analyzer for Nanometer-sized Particles

Size distribution measurements and classification tests by a low pressure differential mobility analyzer (LPDMA) for nanometer-sized silver particles and cesium iodide particles under low pressure conditions (123–300 Torr) were performed using a transmission electron microscope (TEM) and the tandem DMA technique. When the ratio of the sheath gas flow rate and the aerosol gas flow rate was set at 5 : 1, the targeted sizes calculated from the classification voltage applied to the LPDMA at 160 Torr are found to be in good correlation with the count mean Feret diameter obtained from the TEM observation of the particles collected after a classification ranging from 6 to 25 nm, although the targeted sizes set by the LPDMA were approximately 15% greater than the count mean Feret diameter measured by the TEM after classification. The geometric standard deviations of DMA-classified particles measured by TEM and those obtained from the tandem DMA method ranged from 1.08 to 1.17 and from 1.05 to 1.13, respectively. They were slightly greater than the ideal geometric standard deviations (1.05) of the particles classified with the LPDMA, which was calculated by neglecting the broadening effects due to Brownian diffusion. We experimentally demonstrated the validity of our LPDMA system for size measurements and classification of the nanometer-sized particles under low pressure conditions.     

Grafting of hyperbranched cyclotriphosphazene polymer onto silica nanoparticle and carbon black surfaces

The surface grafting of hyperbranched cyclotriphosphazene polymer onto silica nanoparticles and carbon black was investigated. The grafting of hyperbranched cyclotriphosphazene polymer onto these surfaces was achieved by the repeated reactions of hexachlorocyclotriphosphazene with hexamethylenediamine from surface amino groups and sodium carboxylate groups, respectively. The percentage of grafting onto silica and carbon black surfaces exceeded 760 and 390%, respectively. However, it proved difficult to achieve the theoretical growth of cyclotriphosphazene polymer from these surfaces because of steric hindrance. The introduction of sulfonic acid groups was successfully achieved by the reaction of terminal chlorophosphazene groups of the hyperbranched polymer‐grafted silica and carbon black with sulfanilic acid. The content of sulfonic acid groups introduced onto silica and carbon black surfaces was 4.98 mmol/g and 5.70 mmol/g, respectively. The sulfonated cyclotriphosphazene polymer‐grafted carbon black was extremely hydrophilic, yielding stable colloidal dispersions in polar solvents. The sulfonated cyclotriphosphazene polymer‐grafted silica and carbon black showed ionic conductivity, with the conductance increasing exponentially with increasing relative humidity and temperature. This study may offer important leads in the application of silica nanoparticles and carbon black in polymeric membranes for fuel cells. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 4218–4226, 2008     

Mössbauer studies on ultraporous Fe-Oxide/SiO2 aerogel

Magnetic aerogels with very low volume density of ～0.2 g/cm³ were prepared by sol-gel method and supercritical drying. The resulting materials were monolithic and displayed high surface area. By X-ray diffraction and Mössbauer spectroscopy the crystalline phase formed inside the mesopores of the SiO₂ matrix was identified as a spinel iron oxide. Comparison of the magnetic measurements with Mössbauer spectra at various temperatures contributed to the elucidation of the magnetic state of this nanocomposite system with restricted magnetic interactions, in particular its transition to a superparamagnetic state.     

Nanoscale skeletal nickel catalysts prepared via ‘bottom up’ method

NiAl nanoparticles are of considerable importance because of interest in examining the effects of size, surface area, and composition on their physical and catalytic properties. Recently, a new method for the ‘bottom up’ wet chemical preparation of nickel aluminides has been reported. The ability to leach the aluminum from this system provides an entrance to the preparation of skeletal‐type metal catalysts similar to those produced in Raney‐type systems. Furthermore, it is believed that these nanoparticulate catalysts should provide high surface areas and high activities, while the presence of aluminum within the bulk of these catalysts provides additional stability. Here, we present the results of studies conducted on this system which compare their properties and behavior with traditional bulk Raney nickel systems. Additionally, we show that we are able to alter the properties of these nanoparticles by changing the stoichiometric ratio of nickel and aluminum. The properties of all systems have been analyzed through the use of nitrogen adsorption, X‐ray diffraction, and elemental analysis. Finally, the catalysts generated have been compared for their activity in the hydrogenation of butyronitrile. Copyright © 2002 John Wiley & Sons, Ltd.     

Poly(methyl methacrylate)/silica nanocomposite fibers by electrospinning

Uniform poly(methyl methacrylate) (PMMA)/silica nanocomposite fibers containing up to 20 wt % silica were prepared by electrospinning. The electrospun solutions were prepared by mixing a solution of PMMA in dimethyl formamide (DMF) with colloidal silica in methyl ethyl ketone (MEK). The average fiber diameter decreases from 2.49 μm to 1.69 μm when 20 wt % silica is incorporated as a result of considerably increased solution conductivity, although the solution viscosity increases significantly, which should result in opposite effect. Thinner fibers (down to 350 nm) can be obtained by changing DMF/MEK proportion and by the addition of an ammonium salt. Nano‐sized silica particles (10–40 nm) distributes homogeneously in the fibers, as revealed by transmission electron microscopy. Furthermore, the incorporation of silica nanoparticles can change the thermal properties and surface wettability of the fiber mats. © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 47: 1211–1218, 2009