高精度的光纤衰减系数测试系统的设计

利用常规仪器设备，设计了一套集光、机、电为一体的光纤衰减测量,实现了数字化监测显示，并可与微机接口；采用双光路法，消除了由于光源光强不稳定产生的误差。     

Influence of SiO2 in SiCp on the microstructure and impact strength of Al/SiCp composites fabricated by pressureless infiltration

The effect of SiO₂ in SiC_p and the following processing parameters on the microstructure and impact strength of Al/SiC_p composites fabricated by pressureless infiltration was investigated: Mg content in the aluminum alloy, SiC particle size, and holding time. Preforms of SiC_p in the form of rectangular bars (10 × 1 × 1 cm) were infiltrated at 1150°C in an argon→nitrogen atmosphere for 45 and 60 min by utilizing two aluminum alloys (Al-6 Mg-11 Si and Al-9 Mg-11 Si, wt.%). The results obtained show that the presence of SiO₂ in SiC affects the microstructure and impact strength of the composites significantly. When Al₄C₃ is formed, the impact strength decreases. However, a high proportion of SiC to SiO₂ limits the formation of the unwanted Al₄C₃ phase in the composites. Also, a higher content of Mg in the Al alloy lowers the residual porosity and, consequently, increases the composite strength. The impact strength grows with decrease in SiC particle size and increases considerably when the residual porosity is less than 1%. Russian translation published in Mekhanika Kompozitnykh Materialov, Vol. 42, No. 3, pp. 401–418, May–June, 2006.     

Ultrasonic evaluation of anisotropic damage in multiaxially textile-reinforced thermoplastic composites made from hybrid yarns

The basic damage and failure models of multiaxially reinforced composites with a thermoplastic matrix are presented and verified. Within the framework of continuum damage mechanics, a phenomenological model is introduced, where the damage is defined as a change in the elasticity tensor. For damage identification, a specific ultrasonic device was developed. A combination of an immersion set-up and a contact coupling device formed a system for an efficient determination of stiffness-tensor components from convenient sets of velocity measurements. Linked to a tensile machine, it allowed us to measure the anisotropic damage of the new materials group caused by tensile loading. Russian translation published in Mekhanika Kompozitnykh Materialov, Vol. 42, No. 2, pp. 221–234, March–April, 2006.     

An ASE Reduction Filter Using Cascaded Optical Fiber Grating Couplers in EDFA Repeater

A new configuration for an ASE reduction filter in EDFA repeaters for WDM optical transmission systems using optical fiber grating couplers (FGCs) was proposed and first demonstrated. The filtering characteristics of the proposed filter for amplified single wavelength signal and 2-channel WDM signals using EDFA were identified. It was found that the filter was effective to improve SNR in optical domain by reducing ASE noise. The required FGC characteristics for the filter were theoretically predicted under the condition that the total filter loss did not exceed 3 dB. More than 70% of drop efficiency was required in each FGC for the application of the proposed filter to an 8-channel WDM system using EDFA repeaters.     

Influence of the Interaction between Two Neighboring Periodically Curved Fibers on the Stress Distribution in a Composite Material

A method is developed for a stress analysis in an infinite elastic body containing two neighboring periodically cophasaly curved fibers located along two parallel lines. The stress distribution is studied when the body is loaded at infinity by uniformly distributed normal forces in the fiber direction. The investigation is carried out within the framework of a piecewise homogeneous body model with the use of exact three-dimensional equations of elasticity theory. Numerical results related to the stress distribution considered and the influence of interaction between the fibers on this distribution are given.     

Numerical Modeling of Solitons in a Low Birefringent Optical Fiber

A numerical investigation, based on the split-step Fourier transform algorithm of all optical switching of solitons in a low birefringent optical fiber is presented. The numerical algorithm is described in detail. This revised version was published online in August 2006 with corrections to the Cover Date.     

利用模式的对称性研究光子晶体光纤的色散

由光子晶体光纤的对称性可以得到模式分布的对称性，根据模式的对称性选择适当的展开函数，可以使计算量大大减少。计算了六角结构光子晶体光纤的色散特性，得到了波长在1．55pm处色散为零时，光子晶体光纤的结构参量所满足的方程。     

Al/Al2O3P金属基复合材料的静动态压缩性能及损伤分析

用气压浸渗工艺制备了体积分数40％～50％Al2O3颗粒增强纯铝基复合材料，使用了4种不同尺寸的Al2O3颗粒，其平均粒径分别为5μm、10μm、30μm和60μm．测定了这些复合材料的静、动态压缩性能，并通过材料压缩前后密度变化的测量定量表征了材料的累计损伤，结果表明，与基体材料相似，这些复合材料表现出明显的应变率敏感性；当增强颗粒平均粒径小于60μm时，材料的累计损伤基本与应变率无关，而主要取决于材料的应变．材料中颗粒的破裂主要是由颗粒间的相互作用引起的．较小尺寸颗粒增强的复合材料具有较高的流动应力和较小的累计损伤，并随着颗粒体积分数的增加，材料的流动应力和损伤率都相应增加．     

三包层WⅠ和WⅡ型单模光纤波导色散特性的研究

研究了三包层WⅠ和WⅡ型单模光纤的波导色散特性。结果发现在相同条件下，三包层WⅠ和WⅡ型单模光纤零色散点的调节范围比传统的双包层W型单模光纤明显增大。详细分析了几何参量P、Q和光学参量R1、R2对单模传输时的波导色散特性和低次模截止频率的影响。所得的研究结果为获得更为理想的色散补偿、色散平坦光纤及设计新型无源光器件提供了重要的依据。计算波导色散的方法可推广到多包层光纤。