人参二醇对鱼藤酮、MPP+诱导的PC12细胞损伤的作用

目的观察人参二醇对鱼藤酮、MPP+诱导的大鼠嗜铬细胞瘤损伤的影响。方法以大鼠嗜铬细胞瘤PC12细胞为研究对象,以鱼藤酮（0.3、1、3、10、30μmol/L）或MPP+（0.1、0.3、1、3mmol/L）诱导细胞损伤。设阴性对照组、人参二醇对照组（10、25、50、75、100mg/L）、鱼藤酮（3μmol/L,24h）或MPP+（1mmol/L,48h）组,人参二醇（10、25、50、75、100mg/L）联合鱼藤酮（3滋mol/L）或MPP+（1mmol/L）组。采用MTT法检测细胞增殖活性;PI和Hoechst 33342染色检测细胞坏死和凋亡;并以免疫组织化学测定细胞酪氨酸羟化酶（TH）的表达。结果人参二醇（10、25、50、75、100mg/L）本身不会抑制PC12细胞增殖,其中50、75mg/L人参二醇还可促进细胞增殖;各浓度人参二醇对鱼藤酮诱导的细胞损伤均不具有保护作用;在MPP+处理诱导细胞损伤后,50、75mg/L人参二醇可提高细胞增殖活性,但人参二醇对细胞凋亡和坏死及TH的表达无影响。结论人参二醇（50、75mg/L）对MPP+诱导的PC12细胞损伤有保护作用,其作用机制与促进细胞增殖有关;人参二醇对鱼藤酮诱导的细胞损伤无明显保护作用。     

Simultaneous Voltammetric Determination of Cd2+ and Pb2+ in Gasoline Samples Employing a Chemically Modified Acrylonitrile-Butadiene-Styrene (ABS) Composite Electrode

A composite electrode based on acrylonitrile-butadiene-styrene and graphite chemically modified with a bismuth film (AGCE-BiF) was applied for the simultaneous determination of Cd²⁺ and Pb²⁺ in gasoline samples. Extraction induced by microemulsion breaking (EIMB) was used for the first time in the preparation of the samples for electroanalysis. AGCE-BiF was characterized by SEM, AFM, CV, and SWASV. The sensor showed an increase in sensitivity via in situ modification with bismuth film. The LOD was 4 μg L⁻¹ for Cd²⁺ and 2 μg L⁻¹ for Pb²⁺. The results showed satisfactory recoveries and precision, being statistically compatible to those obtained with FAAS.     

Polymeric nanocomposite materials: Preparation and characterization of star-shaped PbS nanocrystals and their influence on the thermal stability of acrylonitrile-butadiene-styrene (ABS) copolymer

Star-shaped PbS nanocrystals were synthesized via a simple hydrothermal reaction between Pb(NO₃)₂·4H₂O and thioglycolic acid at a relatively low temperature. The PbS nanostructures were then combined in a acrylonitrile-butadiene-styrene copolymer. The effect of the PbS nanostructures on the thermal stability of the nanocomposite products has been investigated. The nanostructures and nanocomposite were characterized by X-ray diffraction, scanning electron microscopy, Fourier transform infrared spectra, thermogravimetric-differential thermal analysis and atomic force microscopy. Cone calorimeter measurements showed that the heat release rate significantly decreased in the presence of PbS.     

Preparation of fluorine containing hybrid coatings: investigation of coating performance onto ABS and PMMA substrates

UV‐curable fluorinated organic–inorganic hybrid coatings were prepared by the sol–gel technique. Perfluorinated urethane modified alkoxysilane was synthesized by the reaction between perfluoro alcohol and 3‐isocyanatopropyltrimethoxysilane. The prepared formulations were applied onto poly(methyl methacrylate) (PMMA) and acrylonitrile butadiene styrene (ABS) panels and polymerized by UV‐curing. The properties of the hybrid coatings such as hardness, chemical resistance, thermal stability, surface morphology, double bond conversion, and also contact angle measurements were investigated. Contact angle measurements have shown that the addition of fluorinated silane precursor to the hybrid system improved the water repellency and increased the contact angle from 65° to 106°. Copyright © 2009 John Wiley & Sons, Ltd.     

聚碳酸酯在亚临界水中解聚的研究

采用间歇式高压反应装置研究聚碳酸酯(PC)在亚临界水中的解聚.在温度260～340℃、压力4.8～14.8 MPa、反应时间5～60min的反应条件下,考察了反应温度及反应时间对PC解聚率及主产物双酚A(BPA)和苯酚(PhOH)回收率的影响.产物分别采用傅里叶红外光谱(FTIR)、扫描电子显微镜(SEM)、气质联谱(...     

Analysis of brazilin and protosappanin B in sappan lignum by capillary zone electrophoresis with acid barrage stacking

A method was developed to determine brazilin and protosappanin B in natural products by CE after acid barrage stacking. The optimum conditions were as follows: a BGE of 20 mM sodium tetraborate (pH 9.2) containing 6% v/v of methanol, hydrodynamic injection (0.5 psi, 65 s) followed by hydrodynamic injection of 150 mM citric acid (pH 2.3; 0.5 psi, 22 s), and separated with +25 kV. Under these conditions, brazilin and protosappanin B were separated with a sample‐to‐sample time less than 13 min and detection limits of 0.28 μg/mL and 0.15 μg/mL, respectively. The applicability of the developed method was demonstrated by the detection of brazilin and protosappanin in methanol extract of sappan lignum.     

Surface interaction and corrosion inhibition of carbon steel in sulfuric acid using Petroselinum crispum extract

With the aid of the mass loss (ML) method, and a few electrochemical techniques [potentiodynamic polarization (PDP) and electrochemical impedance spectroscopy (EIS)], the inhibitory impact of Petroselinum crispum (PC) extract on C-steel corrosion in solutions of 1 M sulfuric acid was assessed. By employing Fourier-transform infrared spectroscopy (FT-IR) and X-ray photoelectron spectroscopy (XPS) techniques, the C-steel surface morphology was investigated. The data showed that the solution of plant extract can be effectively utilized to inhibit C-steel corrosion in solutions of 1 M sulfuric acid. The effectiveness of the extract was enhanced by the higher extract dose and rising temperature. The apparent activation energy and the enthalpy of the dissolution process were determined and discussed. The presence of PC decreases the double-layer capacity from 493.1 to 107.3 μF cm⁻² and raises the charge transfer resistance in a solution of 1 M sulfuric acid from 43.39 to 287.7 Ω cm². PC is a mixed-type inhibitor, as demonstrated by PDP tests. The PC extract demonstrated the highest productivity for the C-steel protection up to 90.2% at 300 ppm from the extract, according with the PDP technique. The attained data indicated that PC extract was adsorbed chemically (ΔG^o_ads > 40 kJ mol⁻¹) onto the surface of the C-steel following the Temkin isotherm. The results of numerous tests appear to agree.     

Preparation and evaluation of high-transparent scratch-resistant thin films on plasma treated polycarbonate substrate

New simple aqueous sol–gel procedure has been used for producing hard transparent organic–inorganic coatings on polycarbonate (PC). Sol-gel thins films were prepared by mixing Si and Al aqueous alkoxides and applied on the plasma treated PC. Tetraethyl orthosilicate (TEOS), 3-glycidoxypropyltrimethoxysilane (GPTMS) and aluminum tri sec-butoxide were used as main precursors. Before applying coatings PC were treated by Dielectric Barrier Discharge (DBD) system being conducted at atmosphere pressure. The effects of temperature, sols volume ratios and aging time on the coatings properties were scrutinized. Chemical, structural, morphological, optical and mechanical analyses of the samples were done by ATR-FTIR, EDS, XRD, FE-SEM, TEM, UV/vis spectroscopy, ellipsometry, pencil hardness and eraser scratch methods. TEM results showed well-dispersed nano-particles in the liquid sol. All of the films showed higher average transmittance (89 %) than the raw PC (86 %) that was stemmed from the lower refractive index (1.481) than raw PC (1.58). Films indicated good adhesion onto the plasma treated substrates (5B). The pencil hardness of the PC substrate (4B) improved to 3H (8 pencil grade increment) with just a single layer coating (775 nm thickness) due to the preparation of new hard structures of interlocked Si and Al atoms.     

‘Tail’ phenomenon and fatigue crack propagation of PC/ABS alloy

The fatigue crack propagation (FCP) behavior of the alloy of polycarbonate (PC) and acrylonitrile-butadiene-styrene (PC/ABS) is experimentally investigated in this paper. An improved compliance method is employed to measure the fatigue crack length and optical and scanning electron microscopes (SEM) are used to observe the features of crack tip deformation in situ. ‘Tail’ phenomenon has been observed at the initial stage of fatigue for each specimen, which is regarded as a reflection of the transition process of accumulation of damage and plastic deformation during FCP. The law of FCP from low to high crack growth rate (10⁻⁶-10⁻³ mm/cycle) is obtained and described with Paris law. Porous or dimple features govern the fatigue crack surfaces and coarse features have been seen on the crack surfaces with higher crack growth rate, while smooth features have been observed on the crack surfaces with lower crack growth rate. A stretched band appears when the crack growth transforms from lower to higher region of FCP rate.     

THE EFFECT OF BLENDING SEQUENCE ON PHASE MORPHOLOGY OF NYLON 6/ABS/SMA BLENDS

The preparation process-dependent phase morphology of blends composed of nylon 6 and acrylonitrile-butadiene- styrene(ABS)over a composition range of 30-70 wt% using a styrene-maleic anhydride(SMA)copolymer as the compatibilizing agent with a constant content(5phr)was investigated.The results of the scanning electron microscope (SEM)observation revealed that compared with the binary blends of nylon 6 and ABS,the existence of SMA caused a composition shift of phase inversion to a higher weight fraction of...