Novel fixed‐site–carrier polyvinylamine membrane for carbon dioxide capture

Fixed‐site–carrier membranes were prepared for the facilitated transport of CO₂ by casting polyvinylamine (PVAm) on various supports, such as poly(ether sulfone) (PES), polyacrylonitrile (PAN), cellulose acetate (CA), and polysulfone (PSO). The cast PVAm on the support was crosslinked by various methods with glutaraldehyde, hydrochloric acid, sulfuric acid, and ammonium fluoride. Among the membranes tested, the PVAm cast on polysulfone and crosslinked by ammonium fluoride showed the highest selectivity of CO₂ over CH₄ (>1000). The permeance of CO₂ was then measured to be 0.014 m³ (STP)/(m² bar h) for a 20 μm thick membrane. The effect of the molecular weight of PVAm and feed pressure on the permeance was also investigated. The selectivity increased remarkably with increasing molecular weight and decreased slightly with increased pressure in the range of 1 to 4 bar. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 4326–4336, 2004     

多壁碳纳米管膜湿敏特性的研究

研究了多壁碳纳米管(MWNTs)薄膜的湿敏特性，实验所用的多壁碳纳米管是用热灯丝化学气相沉积法(CVD)合成的.分别对未修饰和修饰的多壁碳纳米管膜温度和湿度特性进行研究后发现，修饰的多壁碳纳米管对温度和湿度非常敏感，且对湿度的响应时间和恢复时间短，重复性好.而未修饰的多壁碳纳米管对温度和湿度不太敏感.对修饰多壁碳纳米管的湿敏特性进行了理论分析，给出了其理论表示式. 关键词： 多壁碳纳米管 化学修饰 湿敏特性 物理吸附     

含氮类金刚石薄膜的紫外辐照研究

 用射频等离子体方法在玻璃基底上制备的类金刚石（DLC）薄膜，采用离子注入法掺氮，并对掺氮DLC薄膜紫外（UV）辐照前后的性能变化进行了研究。研究结果表明：随氮离子注入剂量及UV辐照时间的增加，位于2 930cm^-1附近的SP ³C-H吸收峰明显变小，而位于1 580cm^-1附近的SP2C-H吸收峰则明显增强，薄膜的电阻率明显呈下降趋势；随UV辐照时间的增加，位于1 078cm^-1附近的Si-O-Si键数量及位于786cm^-1附近的Si-C键数量明显增加。即氮离子注入和UV辐照明显改变了DLC薄膜的结构与特性。     

Radioactive Tracer Study of the Displacement of Iodine Adatoms from Platinized Platinum Electrode by Carbon Monoxide

Radioactive tracer studies confirm the earlier electrochemical results that carbon monoxide can virtually completely displace iodine adatoms. For the first time, it is found that iodine adatoms are not displaced by carbon monoxide when iodide anions are adsorbed in the presence of an upd silver monolayer. The possible reasons for the effect observed are discussed.     

Total electron scattering cross sections for carbon dioxide at low electron energies

Absolute total electron scattering cross sections for carbon dioxide have been measured at low electron energies using a photoelectron source. The measurements have been carried out at 27 electron energies varying from 0.91–9.14 eV with an accuracy of ±3%. The cross sections obtained in the present experiment have been compared with other measurements and theoretical computations.     

利用光反射精确测量亚共析碳钢的含碳量

本文从光学角度出发提出了一种经济实用、精度高的测量亚共析碳钢中碳的含量的新方法。阐述了该方法的测量原理，即以金相试样表面对光的反射程度来判定其含碳量，并给出了有关经验公式及数据处理方法。     

MORPHOLOGY OF BLACK CARBON AEROSOLS AND UBIQUITY OF 50-NANOMETER BLACK CARBON AEROSOLS IN THE ATMOSPHERE

Different-sized aerosols were collected by an Andersen air sampler to observe the detailed morphology of the black carbon （BC） aerosols which were separated chemically from the other accompanying aerosols, using a Scanning Electron Microscope equipped with an Energy Dispersive X-ray Spectrometer （SEM-EDX）. The results indicate that most BC aerosols are spherical particles of about 50 nm in diameter and with a homogeneous surface. Results also show that these particles aggregate with other aerosols or with themselves to form larger agglomerates in the micrometer range. The shape of these 50-nm BC spherical particles was found to be very similar to that of BC particles released from petroleum-powered vehicular internal combustion engines. These spherical BC particles were shown to be different from the previously reported fullerenes found using Matrix-Assisted Laser Desorption/Ionization Time-Of-Flight Mass Spectrometry （MALDI-TOF-MS）.     

Reintroduced solids increase inhibitor levels in a pretreated corn stover hydrolysate

Following detoxification of the liquid hydrolysate produced in a corn stover pretreatment process, inhibitor levels are seen to increase with the re-addition of solids for the ensuing hydrolysis and fermentation processes. The solids that were separated from the slurry before detoxification of the liquor contain approx 60% (w/w) moisture, and contamination occurs owing to the diffusion of inhibitors from the moisture entrained in the porous structure of the corn stover solids into the bulk fluid. This evidence suggests the need for additional separation and detoxification steps to purge residual inhibitors entrained in the moisture in the solids. An overliming process to remove furans from the hydrolysate failed to reduce total organic acids concentration, so acids were removed by treatment with an activated carbon powder. Smaller carbon doses proved more efficient in removing organic acids in terms of grams of acid removed per gram of carbon powder. Sugar adsorption by the activated carbon powder was minimal.     

Liquid phase oxidation of p-chlorotoluene to p-chlorobenzaldehyde over cobalt-doped mesoporous titania with a crystalline framework

Cobalt-doped mesoporous titania with a crystalline framework synthesized by surfactant templating method presented highly selective (99%) and reasonable conversion rate (49%) of catalytic oxidation of para-chlorotoluene to para-chlorobenzaldehyde in acetic acid using aqueous hydrogen peroxide as oxidant for the first time. Recycling of the catalyst indicates that the catalyst can be used a number of times without losing its activity to a greater extent. By contrast, cobalt-doped mesoporous titania without a crystalline structure and cobalt doped the commercial titania, Degussa P25 prepared by impregnation method with the similar concentration of cobalt were found inactive. The effects of catalyst concentration, reaction time, reaction temperature, and solvents on the performance of the catalyst were also investigated.     

Isotone relations revisited

We propose a new approach towards proving that the fixed point property for ordered sets is preserved by products. This approach uses a characterization of fixed points in products via isotone relations. First explorations of classes of isotone relations are presented. These first explorations give us hope that this approach could lead to advances on the Product Problem.