Original position statistic distribution analysis (original position analysis)——A new analytical method in research and quality evaluation of materials

The property of the material is closely related to its chemical compositions and microstruc-tures, which are the important parameters in the judgement of the quality of the material. The conventional chemical composition content of the material is an average value of the chemical composition of the whole material tested or the content of a fix position. Although it is still neces-sary to further improve these conventional methods, there are mature and systematic methods for analyzing the conve…     

NEPCⅡ新电子枪热结构分析与测试

北京正负电子对撞机重大改造工程(BEPCⅡ)要求其直线注入器提供更高的能量和流强, 为此必须设计大电流和小发射度的新电子枪, 以提高正电子的产额. 利用ANSYS对BEPCⅡ新电子枪的温度场分布及结构的热变形进行了模拟分析. 对于电子枪复杂的内部结构形态以及能量转换方式, 分析了传导传热方式对温度场的影响. 在此基础上进行了温度场与结构变形的耦合分析, 利用EGUN对电子枪形变前后束流光学特性进行模拟分析, 并对模拟结果与试验 测试结果进行了分析比较.     

Particle Size Analysis by Transmission Fluctuation Spectrometry: Experimental Results Obtained with a Gaussian Beam and Analog Signal Processing

Transmission fluctuation spectrometry (TFS) is a method for the analysis of particle size distributions based on the statistical fluctuations of a transmission signal. Complete information on the PSD and particle concentration can be retrieved by a special transformation of the transmission signal, whereby the expectancy of the transmission square (ETS) is determined after the signal has been subjected to a procedure of spatial and temporal averaging. By varying the averaging parameters over a wide range, a spectrum of ETSs is obtained and introduced into a linear equation system, which yields the PSD. In the experimental realization presented here, variable temporal averaging is realized in the frequency domain with a series of low pass filters at different cutoff frequencies while spatial averaging inevitably occurs as the particles pass through a focused Gaussian beam of finite cross section. Experimental results on spherical particles (glass beads) and non‐spherical particles (SiC) are presented. The PSDs are resolved in 30 intervals within a particle size range from 1–1000 μm, employing a modified Chahine inversion algorithm. So far, the measurements are limited to moderate particle concentrations. Some influences affecting the measurements, especially for higher particle concentrations, are discussed in detail.     

On the Image Regularity Condition

In this paper, we continue the analysis of the image regularity condition (IRC) as introduced in a previous paper where we have proved that IRC implies the existence of generalized Lagrange-John multipliers with first component equal to 1. The term generalized is connected with the fact that the separation (in the image space) is not necessarily linear (when we have classic Lagrange-John multipliers), but it can be also nonlinear. Here, we prove that the IRC guarantees, also in the nondifferentiable case, the fact that 0 is a solution of the first-order homogeneized (linearized) problem obtained by means of the Dini-Hadamard derivatives.     

An existence theorem for neutral variational problems of Bolza

This note proves an existence theorem for a generalized Bolza-type problem that has time delays in both the state and velocity variables. The assumptions are stated in terms of a modification of the classical Hamiltonian, and extend ideas of Rockafellar to the delay case.     

硅色敏器件对复色光色差辨识能力的数值分析

对复色光的光谱功率分布和色敏器件光谱响应的实验曲线进行了函数拟合，采用Mathematica 4．2计算了具有不同峰值波长和半高宽的高斯分布的复色光在色敏器件中产生的电流比．计算结果表明，待测复色光的峰值波长和半高宽变化对两种典型的色敏器件的输出信号影响的权重比分别为100：1和10：1。权重比说明色敏器件的输出电流比随峰值波长和半高宽的变化非常灵敏，但两者权重不同，其中峰值波长的变化影响更为显著，是影响复色光颜色变化的主要因素．数值分析的结果表明，硅双结色敏器件对复色光色差有良好的辨识能力．两种器件权重比的差异说明了器件制作工艺与其辨识能力的关系，为器件合理设计提供了理论依据．     

35Cr25Ni12奥氏体耐热钢中碳化物的电子显微分析

应用扫描电镜（SEM）和透射电镜（TEM）研究了长期使用前后的35Cr25Ni12奥氏体耐热钢中的碳化物演变行为；该钢固溶时效后的组织由初晶奥氏体及M23C6共晶碳化物组成，奥氏体基体中析出了二次M23C6，二次碳化物总是与基体保持立方－立方取向关系；长期使用（3、5年）后，奥氏体中析出的二次碳化物量明显增加，部分M23C6已转变为M6C，M6C与奥氏体基体以及二次碳化物M23C6保持[001]M6C//[221]A//[221]M23C6孪晶取向关系。     

Mesh-Independent Modeling and Moiré Interferometry Studies of Damage Accumulation in Open-Hole Composite Laminates

Mechanics of Composite Materials - A three-dimensional ply-level modeling of multiple matrix cracking near an open hole in a quasi-isotropic composite laminate was performed. A mesh-independent...