Synthesis and characterization of poly(ethylene oxide‐co‐ethylene carbonate) macromonomers and their use in the preparation of crosslinked polymer electrolytes

Methacrylate‐functionalized poly(ethylene oxide‐co‐ethylene carbonate) macromonomers were prepared in two steps by the anionic ring‐opening polymerization of ethylene carbonate at 180 °C, with potassium methoxide as the initiator, followed by the reaction of the terminal hydroxyl groups of the polymers with methacryloyl chloride. The molecular weight of the polymer went through a maximum after approximately 45 min of polymerization, and the content of ethylene carbonate units in the polymer decreased with the reaction time. A polymer having a number‐average molecular weight of 2650 g mol^?1 and an ethylene carbonate content of 28 mol % was selected and used to prepare a macromonomer, which was subsequently polymerized by UV irradiation in the presence of different concentrations of lithium bis(trifluoromethanesulfonyl)imide salt. The resulting self‐supportive crosslinked polymer electrolyte membranes reached ionic conductivities of 6.3 × 10^?6 S cm^?1 at 20 °C. The coordination of the lithium ions by both the ether and carbonate oxygens in the polymer structure was indicated by Fourier transform infrared spectroscopy. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 2195–2205, 2006     

Assessment of filtered gas–solid momentum transfer models via a linear wave propagation speed test

The propagation speeds of linear waves in gas–solid suspensions depend strongly on the solids volume fraction and the wave frequency. The latter is due to gas–solid momentum transfer and allows a simple test on filtered gas–solid momentum transfer models. Such models may predict linear wave propagation speeds different from those obtained with the non-filtered model at wave frequencies higher than the filter frequency, but not at wave frequencies lower than the filter frequency.     

Nd掺杂的Bi4Ti3O12变温X射线衍射分析

利用变温X射线衍射技术，在预烧过程中分析了Nd掺杂Bi4Ti3O12后生成Bi3.15Nd0.85Ti3O12（BNT）相的形成过程以及微结构的变化．实验观察到以30℃／min的升温速率，BNT相在700℃时开始形成，其衍射峰强度随温度的继续升高而增强，衍射峰半高宽随烧结时间延长而减小．X射线衍射分析结果表明，在900℃恒温条件下，烧结约2h，可形成单一的BNT相．     

Pulsed pump: Thermal effects in solid state lasers under super-Gaussian pulses

Solid state laser (SSL) powers can be realistically scaled when pumped by a real, efficient and multimode pulse. In this work, a fourth-order super-Gaussian pulse was assumed as a pump for SSL’s and a complete analytical expression for the thermal phase shift is given. Moreover, the focal length of thermal lens in paraxial ray approximation regime was studied. The results when applied to a Ti: sapphire crystal show an appreciable correction for abberation compared to a top-hat pulse.     

Modelling of composting of food waste in a column reactor

The composting of organic solid waste, the mixture of fruit and vegetable leftovers enriched with night soil, was investigated in a closed thermally insulated reactor. It was found that 80.9 % of the original substrate biodegraded after 14 days. A mathematical model of the column reactor was proposed where the biodegradation rate of the organic solid waste was described using simple n-thorder kinetics. A good prediction of process performance was obtained using the proposed kinetics and experimentally obtained reaction heat. Presented at the 33rd International Conference of the Slovak Society of Chemical Engineering, Tatranské Matliare, 22–26 May 2006.     

电位滴定法测定模拟高放废液中的游离酸

本文研究了用电位滴定法测定模拟高放废液中游离酸的方法。用草酸钾做络合剂以消除Ｆｅ＾３＋、Ａｌ＾３＋、Ｎｄ＾３＋等多种水解离子的影响，用标准碱直接进行电位滴定，即可快速准确地测定模拟高放废液中游离酸的含量。方法的相对标准偏差为１．８％，标准加入回收率为１００－１０１％，能为放射性废物固化试验提供可靠的分析数据。     

LiCoO2中锂离子固相扩散系数随循环次数的变化

The solid diffusion coefficient of lithium-ion in LiCoO₂ cathode material has been investigated by the capacity intermittent titration technique (CITT) at different voltages and at different charge/discharge cycles. By SEM, XRD and FTIR techniques, the structure of LiCoO₂ was studied before and after charge-discharge cycles, and the relationship between solid diffusion coefficient and crystal structure was further discussed. CITT results show that the value of Li⁺ solid diffusion coefficient of LiCoO₂ is about 10^-12 cm²·s^-1. During the whole charge-discharge cycles, the Li⁺ solid diffusion coefficient decreased within the voltage of 4.0～4.3 V, which is attributed to the change of the structure of LiCoO₂.