Effectiveness of linearization of calibration curves in Zeeman graphite furnace atomic absorption spectrometry

A theoretical analysis is made of the effect of analytical line broadening and of non-absorbable radiation in the light source on the shape of concentration curves in Zeeman graphite furnace atomic absorption spectrometry. These results have been used in a systematic study of the effect of spectrometer slit width and hollow-cathode lamp (HCL) current on linearization of calibration graphs for 11 elements: Ag, Au, Bi, Cd, Co, Cu, Fe, Mn, Ni, Pb, and Sb. The effectiveness of linearization throughout the analytical range covered was estimated experimentally on series of 25–30 solutions. Three solutions in each series were used as standards for constructing the calibration graph, the others serving to evaluate the linearization effectiveness. Increasing the slit width and decreasing the HCL current compared to the standard measurement conditions have permitted us to reach a sufficiently high effectiveness of linearization for all the elements studied, with the exception of Ni. The maximum deviation of experimental points from the linear graph under optimum conditions does not exceed 6%. The effect of the Δ parameter used in the computational algorithm on linearization effectiveness is investigated.     

Si3N4陶瓷与灰铸铁配副的摩擦学性能

在Ｍ－２００磨损试验机上于无润滑、蒸馏水润滑、乳化液润滑和１０＾＃机构油润滑４种条件下，对Ｓｉ３Ｎ４陶瓷分别与灰铸铁ＨＴ和Ｔ８钢配副进行了摩擦损性能的对比试验研究。结果表明：Ｓｉ３Ｎ４陶瓷与灰铸铁ＨＴ配副时的摩擦因数和磨损体积在几种润滑环境中均表现出同样的顺序     

FOURIER ANALYSIS OF TEMPORAL AND SPATIAL OSCILLATIONS OF TUNNELING CURRENT IN SCANNING TUNNELING MICROSCOPY

Partially oxidized Si(111) surfaces and surfaces of highly oriented pyrolytic graphite (HOPG) were studied by two different ultrahigh vacuum scanning tunneling microscope (UHV-STM) systems and by an STM system working under ambient conditions, respectively. The STM current images of partially oxidized Si(111) surfaces and HOPG surfaces were analyzed by one/two-dimensional fast Fourier transformation (1D-FFT/2D-FFT). The phenomenon of temporal oscillations of tunneling current on the partially oxidized Si(111) surfaces was detected with both UHV-STM systems. Temporal as well as spatial oscillations of tunneling current appeared in highly resolved STM current images of the Si(111) surfaces simultaneously, but both kinds of oscillations could be discriminated according to their different influence on the 2D-FFT spectra of the current images, while varying the scanning range and rate. On clean HOPG surfaces only spatial oscillations of tunneling current induced by the surface structure were observed.     

用过剩压法生长金刚石过程石墨再结晶现象的研究

 描述了在过剩压驱动下金刚石晶种外延生过程中，大量伴生的石墨再结晶现象。再结晶石墨抑制了金刚石的自发成核；它们分布于合成腔触媒金属的低温区，结晶数量多，晶粒片状分层，尺寸大，但出现乱层晶体结构；同时产生一定数量的无定形碳。分析认为，这与长时间的低过剩压驱动，触媒金属内有足够的碳源供给，并具备在高温高压下石墨充分结晶但又达不到完全石墨化条件有关。还讨论了在低过剩压驱动下，促进金刚石晶体外延生长的碳源可能是活化的碳原子，而不是具有乱层结构特征的再结晶石墨。     

X射线Kirkpatrick-Baez显微镜用超反射镜的研制

 介绍了一种可应用于X射线Kirkpatrick-Baez（KB）显微镜的光学元件—X射线超反射镜。选用的W和B₄C作为镀膜材料，膜对数为20，采用单纯型调优的方法实现了X射线超反射镜设计，用磁控溅射的方法在Si基片上完成了W/B₄C X射线超反射镜的制备。采用高分辨率X射线衍射仪（8 keV）测量了X射线超反射镜的反射特性。制备的X射线超反射镜在掠入射角分别为1.052°和1.143°处，反射角度带宽为0.3°，反射率达到20%，可满足KB型显微镜的要求。     

基于叶绿素荧光光谱分析的稻瘟病害预测模型

为了实现稻瘟病的快速、准确和无损检测,力求构建稻瘟病害预测模型。根据水稻叶片相对病害面积将稻瘟病划分为3个等级,通过激光诱导法采集不同病害等级的活体水稻叶片叶绿素荧光光谱。选取502～830 nm波段激光诱导叶绿素荧光光谱(LICF)作为研究对象,利用Savitzky-Golay平滑法(SG)和一阶导数变换(FDT)对光谱信息进行预处理,通过主成分分析(PCA)方法获取经SG-FDT预处理后光谱的特征向量,根据累积贡献率和方差选取前3个主成分进行分析。将试验样本分为建模样本和检验样本,以稻瘟病害等级为预测指标,利用建模样本的133片叶片的光谱和病害信息分别结合判别分析(DA)、多类逻辑回归分析(MLRA)和多层感知器(MLP)建立稻瘟病的预测模型,利用检验样本的89片叶片的光谱和病害信息对所建模型进行预测检验,完成对PCA-DA、PCA-MLRA和PCA-MLP的对比寻优。结果表明,PCA-DA,PCA-MLRA和PCA-MLP模型均能完成对稻瘟病害的预测,但PCA-MLP模型的平均预测准确率能够达到91.7%,相比PCA-DA和PCA-MLRA模型,在稻瘟病害3个等级上均具有较好的分类和预测能力。     

Graphite–boron composite heater in a Kawai-type apparatus: the inhibitory effect of boron oxide and countermeasures

We have investigated the performance of a graphite–boron composite (GBC) with 3?wt % boron as a precursor for a boron-doped diamond heater in a Kawai-type apparatus at 15?GPa. We first tested a machinable cylinder of GBC sintered at 1000°C in Ar/H₂ gas (99:1 molar ratio). Boron oxide (B₂O₃) formed during sintering frequently hindered the GBC heater from stable operation at temperatures higher than 1400°C by producing melt throughout the heater together with oxide and/or silicates. We then rinsed the GBC heater in hydrochloric acid to remove B₂O₃. After rinsing, we succeeded in stably generating temperatures higher than 2000°C. We also improved a molding process of different-sized GBC tubes for convenient use and tested the molded GBC heater. It was free from the B₂O₃ problem. The electromotive force of the W/Re thermocouple was successfully monitored up to 2400°C.     

A comparison of the magnetic properties of proton- and iron-implanted graphite

In this work we have investigated the changes of the magnetic properties of highly oriented pyrolytic graphite samples after irradiation either with ~3×10¹⁴ protons or 3.5×10¹³ ... 3.5×10¹⁴ iron ions with energies in the MeV range. Our results show that iron and proton irradiations can produce similar paramagnetic contributions depending on the implantation temperature. However, only protons induce a ferromagnetic effect.