Ion chromatography–inductively coupled plasma mass spectrometry determination of arsenic species in marine samples

Arsenic speciation analysis in marine samples was performed using ion chromatography (IC) with inductively coupled plasma mass spectrometry (ICP‐MS) detection. The separation of eight arsenic species, viz. arsenite, monomethyl arsonic acid, dimethylarsinic acid, arsenate, arsenobetaine, tetramethylarsine oxide, arsenocholine and tetramethylarsonium ion was achieved on a Dionex AS4A (weaker anion exchange column) by using a nitric acid pH gradient eluent (pH 3.3 to 1.3). The entire separation was accomplished in 12 min. The detection limits for the eight arsenic species by IC–ICP‐MS were in the range 0.03–1.6 µ g l^?1, based on 3σ of the blank response (n = 6). The repeatability and day‐to‐day reproducibility were calculated to be less than 10% (residual standard deviation) for all eight species. The method was validated by analyzing a certified reference material (DORM‐2, dogfish muscle) and then successfully applied to several marine samples, e.g. oyster, fish muscle, shrimp and marine algae. The low power microwave digestion was employed for the extraction of arsenic from seafood products. Copyright © 2004 John Wiley & Sons, Ltd.     

Reaction of SbPO4 with lithium in non-aqueous electrochemical cells: preliminary study and evaluation of its electrochemical performance in anodes for lithium ion batteries

SbPO₄, a phosphate with a layered structure, was tested as an electrode material for lithium cells spanning the 3.0-0.0 V range. Two main electrochemical processes were detected as extensive plateaus at ca. 1.6 and 0.7 V in galvanostatic measurements. The first process was found to be irreversible, thus excluding a potential intercalation-like mechanism for the reaction and being better interpreted as a decomposition reaction leading to the formation of elemental Sb. This precludes the use of this compound as a cathodic material for lithium cells. By contrast, the process at 0.7 V is reversible and can be ascribed to the formation of lithium-antimony alloys. The best electrochemical response was obtained by cycling the cell at a C/20 discharge rate over the voltage range 1.25-0.25 V. Under these conditions, the cell delivers an average capacity of 165 Ah/kg—a value greater than those reported for other phosphates—upon successive cycling.     

高剥离类镁等电子序列的磁偶极M1和电四极E2光谱跃迁理论研究

利用全相对论性多组态Dirac-Fock广义平均能级方法，系统地计算了类镁离子3s3p磁偶极Ml^3P2--^3P1和电四极E2 ^2P2--^3P0(Z=20-103)光谱跃迁的能级间隔、跃迁几率和振子强度。计算中考虑了原子核的有限体积效应，进行了高阶Breit修正和QED修正，所得到的能级间隔和最近的实验数据及理论计算值进行了比较。计算结果表明：高原子序数的高荷电离子的磁偶极矩M1和电四极矩E2跃迁几率和中性原子的电偶极E1的相当，在ICF和MCF高温激光等离子体中，磁偶极矩M1和电四极矩E2跃迁过程不容被忽视。     

Heavy metal ion uptake properties of polystyrene-supported chelating polymer resins

Metal ion uptake properties of polystyrene-supported chelating polymer resins functionalized with (i) glycine, (ii) hydroxy benzoic acid, (iii) Schiff base and (iv) diethanol amine have been investigated. The effects of pH, time and initial concentration on the uptake of metal ions have been studied. The uptake of metal ion depends on pH. The resins are more selective at pH 10 for Pb(II) and Hg(II), whereas at pH 6 they are found to be Cd(II) and Cr(VI) selective. Metal ion uptake properties of resins follow Freundlich’s equation. The resins are recyclable and are therefore employed for the removal of heavy metal pollutants from industrial waste water.     

Self-organized amorphous material in silicon (0 0 1) by focused ion beam (FIB) system

A method using a focused ion beam (FIB) to prepare a silicon amorphous material is presented. The method involves the redeposition of sputtered material generated during the interaction of the Ga⁺ ion beam with a silicon substrate material. The shape and dimensions of this amorphous material are self-organized and reproducible. The stability of this amorphous material under electron irradiation was investigated in the transmission electron microscopy (TEM). Electron irradiation can induce recrystallization of the amorphous material, resulting in the lateral and vertical growth, starting at an amorphous-crystalline interface, of polysilicon containing defects.     

SURFACE METALLIZATION OF CENOSPHERES AND PRECIPITATORS BY ELECTROLESS PLATING

This paper reports the use of a colloidal Pd^0 catalysis system to metallize the surface of precipitators separated from coal fly-ash, and metals such as Cu, Ni etc. are deposited on the precipitators surface. Alternatively, according to the characteristic surface of cenospheres, an Ag coating catalysis system is adopted to first deposit Ag on the cenospheres surface, followed, if necessary, by the deposition of other metals such as Cu, Ni, etc. on the Ag coating to produce monolayer and multilayer metal-coated cenospheres. The surface characteristics and the morphologies of the metal coatings are examined in detail with scanning electron microscopy (SEM), energy dispersive spectroscopy (EDX) and X-ray photoelectron spectroscopy (XPS) techniques. It can be shown that the quality of metal coatings derived from the Aa coatina catalysis system, is better than that of the colloidal Pd^0 catalysis system.     

Preparation of a cyclodextrin dimer linked with a bis(picolinyl)cystine moiety and its intra- and intermolecular inclusion behavior

A novel cyclodextrin (CD) dimer linked with a bis(picolinyl)cystine (Cys) moiety was prepared by the coupling of Boc-protected Cys with amino-modified CDs, followed by deprotection of the Boc groups and bispicolinylation. The dimer showed less affinity to an organic guest molecule compared to that of a native CD monomer. It was attributed to an intramolecular inclusion of the pyridine moiety into CD cavity. The dimer caused significant increase of its organic guest affinity by an addition of a copper ion. The included pyridine group may come out of a CD cavity to bind the copper ion and the two CDs included cooperatively and intermolecularly a guest molecule with high affinity.     

K＋－SrO－La_2O_3／ZnO催化剂上甲烷氧化偶联反应Ⅰ．催化活性和反应气中添加CO_2的影响

Ｋ＋┐ＳｒＯ┐Ｌａ２Ｏ３／ＺｎＯ催化剂上甲烷氧化偶联反应＊Ⅰ．催化活性和反应气中添加ＣＯ２的影响余林徐奕德＊＊郭燮贤（中国科学院大连化学物理研究所催化基础国家重点实验室，大连１１６０２３）关键词钾离子，氧化锶，氧化镧，氧化锌，金属氧化物催化剂，甲烷，...     

Chemical imaging in biology and medicine using ion microscopy

The ability to quantitatively map the distribution of elements on the micrometer scale and smaller with high sensitivity and isotopic discrimination is unique to ion microscopy. The information contained in ion images can be crucial to the study of the solid state, where chemical heterogeneity is often directly related to observed behavior. The tools of digital image processing allow the extraction of quantitative information from the image data. These techniques coupled with improved instrumentation for the detection of ion images drastically increase the problem solving capabilities of the ion microscope. The use of such methods and instrumentation in the ion microscopic analyses of cell cultures and tissues of biological and biomedical relevance will be discussed.     

Low-energy ion-assisted control of interfacial structures in metallic multilayers

A molecular dynamics method has been used to simulate the argon ion-assisted deposition of Cu/Co/Cu multilayers and to explore ion beam assistance strategies that can be used during or after the growth of each layer to control interfacial structures. A low-argon ion energy of 5–10 eV was found to minimize a combination of interfacial roughness and interlayer mixing (alloying) during the ion-assisted deposition of multilayers. However, complete flattening with simultaneous ion assistance could not be achieved without some mixing between the layers when a constant ion energy approach was used. It was found that multilayers with lower interfacial roughness and intermixing could be grown either by modulating the ion energy during the growth of each metal layer or by utilizing ion assistance only after the completion of each layers deposition. In these latter approaches, relatively high-energy ions could be used since the interface is buried and less susceptible to intermixing. The interlayer mixing dependence upon the thickness of the over layer has been determined as a function of ion energy.