A recommended and verified procedure for in situ tryptic digestion of formalin‐fixed paraffin‐embedded tissues for analysis by matrix‐assisted laser desorption/ionization imaging mass spectrometry

Matrix‐assisted laser desorption/ionization imaging mass spectrometry (MALDI IMS) is a molecular imaging technology uniquely capable of untargeted measurement of proteins, lipids, and metabolites while retaining spatial information about their location in situ. This powerful combination of capabilities has the potential to bring a wealth of knowledge to the field of molecular histology. Translation of this innovative research tool into clinical laboratories requires the development of reliable sample preparation protocols for the analysis of proteins from formalin‐fixed paraffin‐embedded (FFPE) tissues, the standard preservation process in clinical pathology. Although ideal for stained tissue analysis by microscopy, the FFPE process cross‐links, disrupts, or can remove proteins from the tissue, making analysis of the protein content challenging. To date, reported approaches differ widely in process and efficacy. This tutorial presents a strategy derived from systematic testing and optimization of key parameters, for reproducible in situ tryptic digestion of proteins in FFPE tissue and subsequent MALDI IMS analysis. The approach describes a generalized method for FFPE tissues originating from virtually any source.     

Determination of total phosphorus and nitrogen in turbid waters by oxidation with alkaline potassium peroxodisulfate and low pressure microwave digestion, autoclave heating or the use of closed vessels in a hot water bath: comparison with Kjeldahl digestion

The evaluation of the use of alkaline peroxodisulfate digestion with low pressure microwave, autoclave or hot water bath heating for the determination of total phosphorus and nitrogen in turbid lake and river waters is described. The efficiency of these digestion procedures were compared to a Kjeldahl digestion procedure with sulphuric acid-potassium sulfate and copper sulfate. The final solution before digestion was 0.045 M in potassium peroxodisulfate and 0.04 M in sodium hydroxide. Procedures were evaluated by the analysis of suspensions of two reference materials, National Institute of Environmental Science, Japan, no. 3 Chlorella and no. 2 pond sediment and natural turbid waters. Best recoveries of phosphorus and nitrogen by microwave heating were obtained when solutions were digested at 95 °C for 40 min. Quantitative recoveries of phosphorus from Chlorella suspensions up to 1000 mg/l were obtained by all three heating procedures, but incomplete recoveries of nitrogen occurred above 20 mg N/l in the digested sample. Good recoveries of phosphorus and nitrogen from suspended sediment suspensions were obtained only from solutions containing <150 mg/l of suspended sediments. Recoveries of phosphorus from phosphorus compounds containing COP and CP bonds added to distilled water were quantitative (94-113%) except for polyphosphates (microwave, 34±8; autoclave, 114±6; water bath, 96±4) and aluminium phosphate (8-23%). Recoveries of nitrogen compounds containing CN bonds added to distilled water were quantitative (94-96%). The analysis of a range of natural turbid water samples by alkaline peroxodisulfate and microwave, autoclave and water bath heating gave similar total phosphorus and nitrogen results. All procedures using alkaline peroxodisulfate underestimate phosphorus concentrations at high suspended sediment concentrations (>150 mg/l) and are only suitable for the analysis of very turbid samples when the turbidity is due to organic matter (algal cells, plant detritus). Underestimation of nitrogen occurs when samples contain more than 20 mg N/l.     

LiMn2O4的湿法合成及锰的光度法测定研究

The LiMn₂O₄ spinel was prepared by wet method using Li₂CO₃， Mn(CH₃COO)₂·4H₂O and CO₂ as raw ma-terials. The products were measured by TG/DTA， XRD， IR. The results Showed that the sample calcined at 800℃ for 10h was well crystallized monophase product. The contents of Mn(Ⅲ) and Mn(Ⅳ) of LiMn₂O₄ spinel were determined simultaneously by spectrophotometric analysis with pyrophosphoric acid.     

Pressurized wet digestion in open vessels

The High Pressure Asher (HPA-S) was adapted with a Teflon liner for pressurized wet digestion in open vessels. The autoclave was partly filled with water containing 5% (vol/vol) hydrogen peroxide. The digestion vessels dipped partly into the water or were arranged on top of the water by means of a special rack made of titanium or PTFE-coated stainless steel. The HPA-S was closed and pressurized with nitrogen up to 100 bars. The maximum digestion temperature was 250 °C for PFA vessels and 270 °C for quartz vessels. Digestion vessels made of quartz or PFA-Teflon with volumes between 1.5 mL (auto sampler cups) and 50 mL were tested. The maximum sample amount for quartz vessels was 0.5–1.5 g and for PFA vessels 0.2–0.5 g, depending on the material. Higher sample intake may lead to fast reactions with losses of digestion solution. The samples were digested with 5 mL HNO₃ or with 2 mL HNO₃+6 mL H₂O+2 mL H₂O₂. The total digestion time was 90–120 min and 30 min for cooling down to room temperature. Auto sampler cups made of PFA were used as digestion vessels for GFAAS. Sample material (50 mg) was digested with 0.2 mL HNO₃+0.5 mL H₂O+0.2 mL H₂O₂. The analytical data of nine certified reference materials are also within the confidential intervals for volatile elements like mercury, selenium and arsenic. No cross contamination between the digestion vessels could be observed. Due to the high gas pressure, the diffusion rate of volatile species is low and losses of elements by volatilisation could be observed only with diluted nitric acid and vessels with large cross section. In addition, cocoa, walnuts, nicotinic acid, pumpkin seeds, lubrication oil, straw, polyethylene and coal were digested and the TOC values measured. The residual carbon content came to 0.2–10% depending on the sample matrix and amount.     

Analysis of additive metals in fuel and emission aerosols of diesel vehicles with and without particle traps

Fuel additives used in particle traps have to comply with environmental directives and should not support the formation of additional toxic substances. The emission of metal additives from diesel engines with downstream particle traps has been studied. Aspects of the optimisation of sampling procedure, sample preparation and analysis are described. Exemplary results in form of a mass balance calculation are presented. The results demonstrate the high retention rate of the studied filter system but also possible deposition of additive metals in the engine.     

Production and energetic use of biogas from energy crops and wastes in Germany

The production of biogas for reducing fossil CO₂ emissions is one of the key strategic issues of the German government and has resulted in the development of new process techniques and new technologies for the energetic use of biogas. Progress has been made in cultivating energy crops for biogas production, in using new reactor systems for anaerobic digestion, and in applying more efficient technologies for combined heat and power production. Recently, integration of fuel cells within the anaerobic digestion process was started, and new technologies for biogas upgrading and conversion to hydrogen were tested. This article describes the trends in Germany for achieving more efficient energy production.     

微波消解ICP-AES法测定ABS中Pb、Cd、Hg

以ABS塑料为研究对象,采用微波消解法进行样品的前处理,使用电感耦合等离子体发射光谱法测定ABS塑料中Pb、Cd、Hg,结果表明,Pb、Cd、Hg加标回收率均在95~105%之间,测试精密度均小于3%,该方法在缩短样品前处理时间的同时得到较高的元素消解回收率和较为理想的精确度,适用于ABS塑料中重金属含量的快速测定。     

CATALYTIC WET PEROXIDE OXIDATION OF HYDROQUINONE WITH Co（II）/ACTIVE CARBON CATALYST LOADED IN STATIC BED

Catalysts based on Co（II） supported on active carbon were prepared and loaded in static bed. The hydroquinone would be degraded completely after treated by Catalytic wet peroxide oxidation method with Co（II）/active carbon catalyst. After activate treatment, the active carbon was immerged in cobaltous nitrate solution, then put into a drying oven, Co（II） could be loaded on the micro-surface of carbon. Taking the static bed as the equipment, the absorption of active carbon and catalysis of Co（II） was used to reduce activation energy of hydroquinone. Thus hydroquinone could be drastically degraded and the effluent can be drained under the standard. Referring to Fenton reaction mechanism, experiment had been done to study the heterogeneous catalyzed oxidation mechanism of Co（II）. The degradation rate of hydroquinone effluent could be achieved to 92% when treated in four columns at H2O2 concentration 10%, reaction temperature 40 ℃, pH 5 and reaction time 2.5h.     

微波辅助快速制备2D/1D ZnIn2S4/TiO2 S型异质结及其光催化制氢性能

The threat and global concern of energy crises have significantly increased over the last two decades. Because solar light and water are abundant on earth, photocatalytic hydrogen evolution through water splitting has been considered as a promising route to produce green energy. Therefore, semiconductor photocatalysts play a key role in transforming sunlight and water to hydrogen energy. To date, various photocatalysts have been studied. Among them, TiO₂ has been extensively investigated because of its non-toxicity, high chemical stability, controllable morphology, and high photocatalytic activity. In particular, 1D TiO₂ nanofibers (NFs) have attracted increasing attention as effective photocatalysts because of their unique 1D electron transfer pathway, high adsorption capacity, and high photoinduced electron–hole pair transfer capability. However, TiO₂ NFs are considered as an inefficient photocatalyst for the hydrogen evolution reaction (HER) because of their disadvantages such as a large band gap (~3.2 eV) and fast recombination of photoinduced electron–hole pairs. Therefore, the development of a high-performance TiO₂ NF photocatalyst is required for efficient solar light conversion. In recent years, several strategies have been explored to improve the photocatalytic activity of TiO₂ NFs, including coupling with narrow-bandgap semiconductors (such as ZnIn₂S₄). Recently, microwave (MW)-assisted synthesis has been considered as an important strategy for the preparation of photocatalyst semiconductors because of its low cost, environment-friendliness, simplicity, and high reaction rate. Herein, to overcome the above-mentioned limiting properties of TiO₂ NFs, we report a 2D/1D ZnIn₂S₄/TiO₂ S-scheme heterojunction synthesized through a microwave (MW)-assisted process. Herein, the 2D/1D ZnIn₂S₄/TiO₂ S-scheme heterojunction was constructed rapidly by using in situ 2D ZnIn₂S₄nanosheets decorated on 1D TiO₂ NFs. The loading of ZnIn₂S₄ nanoplates on the TiO₂ NFs could be easily controlled by adjusting the molar ratios of ZnIn₂S₄ precursors to TiO₂ NFs. The photocatalytic activity of the as-prepared samples for water splitting under simulated solar light irradiation was assessed. The experimental results showed that the photocatalytic performance of the ZnIn₂S₄/TiO₂ composites was significantly improved, and the obtained ZnIn₂S₄/TiO₂ composites showed increased optical absorption. Under optimal conditions, the highest HER rate of the ZT-0.5 (molar ratio of ZnIn₂S₄/TiO₂= 0.5) sample was 8774 μmol·g^-1·h^-1, which is considerably higher than those of pure TiO₂ NFs (3312 μmol·g^-1·h^-1) and ZnIn₂S₄nanoplates (3114 μmol·g^-1·h^-1) by factors of 2.7 and 2.8, respectively. Based on the experimental data and Mott-Schottky analysis, a possible mechanism for the formation of the S-scheme heterojunction between ZnIn₂S₄ and TiO₂ was proposed to interpret the enhanced HER activity of the ZnIn₂S₄/TiO₂heterojunctionphotocatalysts.      

Evaluation of closed-vessel microwave digestion method for the determination of trace impurities in polymer-based photoresist by inductively coupled plasma mass spectrometry

A closed microwave digestion method followed by inductively coupled plasma spectrometric (ICP-MS) analysis was evaluated for the determination of trace impurities in photoresist. To optimize the digestion procedure, several digestion parameters such as acid, heating temperature and heating time were evaluated. Besides, the digestion efficiency of used photoresist material and the recovery of analyte elements obtained by the use of gravimetric method and ICP-MS measurement, individually, were also compared to clarify the completeness of digestion. According to our experiments, the gravimetric method was found to be not so relevant to the completeness of digestion, because the remaining sample matrix could cause suppression effect in the subsequent ICP-MS measurement. In view of minimizing blank value and working time, a simple single-step heating program was proposed to mineralize 0.25 ml of photoresist material with 5 ml of nitric acid at 180 °C for 10 min. Based on the comparative study of the analytical results obtained by instrumental neutron activation analysis (INAA) and proposed method, the reliability of proposed method for the determination of trace metallic impurities in photoresist material has been confirmed.