状态转变增强拉曼光谱

表面增强拉曼散射(SERS)是公认的超灵敏的光谱工具.和传统的优化SERS基底材料或构筑完美的结构策略相比,我们提出了一种极其简单和灵敏的方法,该方法被命名为状态转变增强拉曼光谱(STERS).这种STERS检测方法可广泛的应用于毒品安全检测、食品安全和环境保护等方面.如果我们把这种方法和便携式拉曼光谱仪结合,这种应用...     

193 nm氟化物增透膜的特性

 为了研制低损耗、高性能的193 nm氟化物增透膜,研究了基底和不同氟化物材料组合对氟化物增透膜的影响。在熔石英基底上,将挡板法和预镀层技术相结合,采用热舟蒸发方式制备了不同氟化物材料组合增透膜,对增透膜的剩余反射率和光学损耗等光学特性,以及表面粗糙度和应力等特性进行了测量和比较。在分析比较和优化的基础上,设计制备的3层1/4波长规整膜系AlF3/LaF3增透膜在193 nm的剩余反射率低于0.14%,单面镀膜增透膜的透射率为93.85%,增透膜表面均方根粗糙度为0.979 nm,总的损耗约为6％。要得到高性能的193 nm增透膜,应选用超级抛光基底。     

超光滑基片表面散射的数值研究

以一阶微分散射理论为基础,从理论和模拟两个方面对超光滑基片表面的散射电磁场进行了数值研究.分析了s偏振光和p偏振光的微分散射随入射角和散射角的分布情况.研究发现,当入射角较大时,p偏振光在某个散射方向的微分散射为0,而无论入射角和散射角如何变化,s偏振光的微分散射均大于0.当用光散射法对超光滑基片进行表面测试时,相对于...     

Synthesis surface effects on the stress and deformation of film/substrate system

The closed-form solutions of bending curvature and stress distribution in film/substrate system with the synthesis surface effect are proposed by minimizing the total potential energy. Effects of the roughness and the residual surface stress on stress in film are addressed. Results reveal that, at a given thickness of the substrate, effects of roughness and residual surface stress on the bending curvature become significant with decreasing the film thickness. The roughing surface will enlarge the magnitudes of bending curvature and film stress. The direction change of residual surface stresses can lead to a reversed bending of film/substrate system.     

Swiss-Roll燃烧器催化剂结构的实验研究

实验研究了装有Pt覆盖的多孔陶瓷的Swiss-Roll燃烧器的燃烧特性,分别得到了3种不同长度的催化剂基底的熄火极限,并测量3种情况下催化剂壁面及催化剂后部空间的温度。实验结果表明,3种情况中,催化剂基底长4.5mm的燃烧器可燃范围最大,所以此长度较适合此Swiss-Roll燃烧器。从温度数据可以看出来,催化剂后部空间存在反应,且受上游催化剂表面反应强度的影响。     

Finite element buckling analysis of multi-layered graphene sheets on elastic substrate based on nonlocal elasticity theory

Graphene-polymer nano-composites are one of the most applicable engineering nanostructures with superior mechanical properties. In the present study, a finite element (FE) approach based on the size dependent nonlocal elasticity theory is developed for buckling analysis of nano-scaled multi-layered graphene sheets (MLGSs) embedded in polymer matrix. The van der Waals (vdW) interactions between the graphene layers and graphene-polymer are simulated as a set of linear springs using the Lennard-Jones potential model. The governing stability equations for nonlocal classical orthotropic plates together with the weighted residual formulation are employed to explicitly obtain stiffness and buckling matrices for a multi-layered super element of MLGS. The accuracy of the current finite element analysis (FEA) is approved through a comparison with molecular dynamics (MD) and analytical solutions available in the literature. Effects of nonlocal parameter, dimensions, vdW interactions, elastic foundation, mode numbers and boundary conditions on critical in-plane loads are investigated for different types of MLGS. It is found that buckling loads of MLGS are generally of two types namely In-Phase (INPH) and Out-of-Phase (OPH) loads. The INPH loads are independent of interlayer vdW interactions while the OPH loads depend on vdW interactions. It is seen that the decreasing effect of nonlocal parameter on the OPH buckling loads dwindles as the interlayer vdW interactions become stronger. Also, it is found that the small scale and polymer substrate have noticeable effects on the buckling loads of embedded MLGS.     

Method for modulating the wafer bow of free-standing GaN substrates via inductively coupled plasma etching

The bowing curvature of the free-standing GaN substrate significantly decreased almost linearly from 0.67 to 0.056 m⁻¹ (i.e. the bowing radius increased from 1.5 to 17.8 m) with increase in inductively coupled plasma (ICP) etching time at the N-polar face, and eventually changed the bowing direction from convex to concave. Furthermore, the influences of the bowing curvature on the measured full width at half maximum (FWHM) of high-resolution X-ray diffraction (HRXRD) in (0 0 2) reflection were also deduced, which reduced from 176.8 to 88.8 arcsec with increase in ICP etching time. Decrease in the nonhomogeneous distribution of threading dislocations and point defects as well as V_Ga–O_N complex defects on removing the GaN layer from N-polar face, which removed large amount of defects, was one of the reasons that improved the bowing of the free-standing GaN substrate. Another reason was the high aspect ratio of needle-like GaN that appeared at the N-polar face after ICP etching, which released the compressive strain of the free-standing GaN substrate. By doing so, crack-free and extremely flat free-standing GaN substrates with a bowing radius of 17.8 m could be obtained.     

Synthesis and Characterization of New Adhesion Promoter for Grafting Conducting Polymer on Oxide Substrate

For grafting polypyrrole layers on oxidic substrates, the synthesis and characterization of a new adhesion promoter 11‐(pyrrol‐3‐yl) undecyl trimethoxysilane (PyTMS) were described in this article. The oxidation potential of PyTMS was determined by cyclic voltammetry. The grafting behavior of such an adhesion promoter on oxidized surface and chemical deposition of polypyrrole over the modified oxidized surface were studied. The adsorbed layer on the oxidized substrates thus formed was determined by both contact angle measurements and X‐ray photoelectron spectroscopy. Chemical polymerization of terminal pyrrole moieties on such substrates yielded adhesive polypyrrole films, and SEM image showed that the morphology of the polypyrrole films was influenced by the experimental conditions.     

Improvement of water and oil repellency on wood substrates by using fluorinated silica nanocoating

We have investigated a one-step fabrication of fluoro-containing silica coating on wooden substrates, showing multi-functions including super repellency toward water and sunflower oil, low sliding angles, good durability, and low adsorption capacity of moisture. The repellent slurry, consisting of well-mixing silica nanospheres and perfluoroalkyl methacrylic copolymer, is simply prepared and subsequently sprayed over wooden substrates with good adhesion. It has shown that the decoration of silica nanospheres on microscaled wooden texture acts as a crucial role in improving the repellency toward water and sunflower oil droplets. The maximal contact angles can reach as high as 168.3° and 153.6° for water and sunflower oil drops, respectively. These analyses of wetted fraction and work of adhesion also demonstrate the improved repellency due to the addition of silica. This improvement of the repellencies is ascribed to the fact that the drops partially sit on F-coated silica spheres, leaving a layer of air underneath the droplet (i.e., Cassie state). On the basis of the results, the multi-functional coating on wooden substrates delivers a promising commercial feasibility on a variety of woodworks.     

Magnetic properties of Terfenol-D film on a compliant substrate

Substrate thickness effects on the magnetization and magnetostriction of Terfenol-D films was studied by using a nonlinear constitutive model combined with the Timosheko elastic theory. Results show that characteristics of Terfenol-D films on compliant substrates are different from those of their bulk counterpart. Tunable properties can be obtained by adjusting the film/substrate thickness ratio.