单壁碳纳米管的快速、高效提纯方法研究

本文采用改进的流化床装置对碳纳米管进行空气氧化处理、浓盐酸浸泡处理、空气氧化、浓盐酸浸泡组合处理, 利用扫描电镜和拉曼光谱方法检测了四种处理方法对碳纳米管提纯的效果, 结果发现, 在873 K经空气氧化30分钟, 再用浓盐酸浸泡10分钟, 这种组合处理方法下, 得到的单壁碳管纯度最高, 产率最大。     

柴油机进气道喷射甲醇的排放与经济性研究

在一台增压中冷的电控单体泵柴油机上采用柴油/甲醇组合燃烧（DMCC）方式进行排放特性与经济性试验研究。结果表明:采用DMCC方式能够大量减少NO_x排放,同时CO₂排放也有所降低。可以通过在排气管上加装氧化催化转换器（DOC）很好地清除掉DMCC方式增加的HC和CO排放,其催化效率在90%以上,比原机排放低很多,DMCC方式的甲醛排放比原机高,DOC对其催化率达98%,接近超低排放。DMCC模式外特性的热效率提高了7.607%,且存在一个最佳燃料匹配区间。     

Influence of the Particle Morphology on the Activity of Nanometer Platinum Aerosol Catalysts

For nanoparticle agglomerates, the catalytic activity may depend strongly on their structure. The influence of different parameters such as agglomerate structure, primary particle temperature history and surface preconditioning on the catalytic activity of nanoparticles was investigated. The fraction of agglomerate surface contributing to the reaction depends on the agglomerate structure and on the velocity of the reaction under investigation. For extremely fast reactions such as the oxidation of hydrogen on Pt nanoparticles, only the outermost surface (exposed surface) contributes substantially to the formation of water. For the system investigated here, the inner surface not substantially contributing to the reaction accounted for at least 70% of the total particle surface as determined from oxygen presaturation experiments of the agglomerate surface. A considerable activity loss of the platinum particles was observed on preheating the nanoparticle agglomerates. The preheating leads to an increase in the nanoparticle size by an order of magnitude due to sintering. It is unclear if this activity reduction is due to changes in the particle surface state or to a real size effect of the nanoparticles.     

Microstructure, bonding strength and thermal shock resistance of ceramic coatings on steels prepared by plasma electrolytic oxidation

Ceramic coatings were successfully prepared on steel by plasma electrolytic oxidation (PEO) in aluminate electrolyte and silicate electrolyte, respectively. The microstructure of the coatings including surface morphology, phase and element composition were studied by scanning electron microscopy (SEM) and X-ray diffraction (XRD), respectively. The bonding strength between the ceramic coating and the substrate was tested using different methods including tensile tests and shearing tests. The thermal shock resistance of the coatings was also evaluated. The results indicated that coatings obtained in both electrolytes were porous and coarse. The average diameters of the pores were below 10 μm. PEO coatings obtained in aluminate electrolyte were composed of Fe₃O₄ and FeAl₂O₄, while those obtained in silicate electrolyte were in a noncrystal state. PEO coatings obtained in aluminate electrolyte showed similar change trend of tensile strength and shearing strength with increasing treating time, namely, a relatively high values with middle time treating and low value with short and long time treating. The best coating was the samples treated with 30 min, whose tensile strength was 20.6 MPa and shearing strength was 16 MPa. The tensile strength and shearing strength of coatings obtained in silicate electrolyte were not strongly influenced by the treating time, the values of which were range in 14 ± 2 MPa and 11 ± 2 MPa, respectively. Coatings obtained in both electrolytes showed the best thermal shock resistance with middle time treating. Coatings obtained in silicate electrolyte show a little better thermal shock resistance than those obtained in aluminate electrolyte.     

Data for scaling-up hydrothermal waste water treatment process

Abstract

Hydrothermal oxidation of wastes is developed as an alternative technique in order to limit the toxic end-product formation, the waste volume and the energy supply. We are now working on the transfer of this technology, and so on the determination of data for scaling-up the hydrothermal oxidation process. The main data concern the knowledge of reactive pathway, the determination of reaction kinetic and thermal parameter. Kinetic and thermal data have been determined for the hydrothermal oxidation of acetic acid as well as the reactive pathway of hydrothermal oxidation of a C, H, O, N compound, the fenuron (C₆H₅-NH-CO-N(CH₃)₂).     

Methane-Derived Carbonates in a Native Sulfur Deposit: Stable Isotope and Trace Element Discriminations Related to the Transformation of Aragonite to Calcite

Abstract

Stable isotope (¹³C, ¹⁸O, ³⁴S) and trace element (Sr²⁺, Mg²⁺, Mn²⁺, Ba²⁺, Na⁺) investigations of elemental sulfur, primary calcites and mixtures of aragonite with secondary, post-aragonitic calcite from sulfur-bearing limestones have provided new insights into the geochemistry of the mineral forming environment of the native sulfur deposit at Machów (SE-Poland). The carbon isotopic composition of carbonates (δ¹³C = ?41 to ?47‰ vs. PDB) associated with native sulfur (δ³⁴S = + 10 to + 15‰ vs. V-CDT) relates their formation to the microbiological anaerobic oxidation of methane and the reduction of sulfate derived from Miocene gypsum. From a comparison with experimentally derived fractionation factors the element ratios of the aqueous fluids responsible for carbonate formation are estimated. In agreement with field and laboratory observations, ratios near seawater composition are obtained for primary aragonite, whereas the fluids were relatively enriched in dissolved calcium during the formation of primary and secondary calcites. Based on the oxygen isotope composition of the carbonates (δ¹⁸O = ?3.9 to ?5.9‰ vs. PDB) and a secondary SrSO₄ (δ¹⁸O = + 20‰ vs. SMOW; δ³⁴S = + 59‰ vs. V-CDT), maximum formation temperatures of 35°C (carbonates) and 47°C (celestite) are obtained, in agreement with estimates for West Ukraine sulfur ores. The sulfur isotopic composition of elemental sulfur associated with carbonates points to intense microbial reduction of sulfate derived from Miocene gypsum (δ³⁴S ≈ + 23‰) prior to the re-oxidation of dissolved reduced sulfur species.     

1.65μm附近CH4分子高分辨率吸收光谱研究

采用连续可调谐二极管半导体激光器为探测光源,以可调怀特型长光程多通池(46.36～1158.90m)作为吸收池,采用直接吸收的方法,探测了室温下1.65μm附近CH4分子的高分辨率吸收光谱。在6043.00～6053.72cm-1范围内探测了5组不同压力和光程下的吸收光谱,观测到了259条线新的CH4分子吸收谱线,实验数据用Gaussian线型进行拟合,得到了这些吸收谱线的线强、线位置以及线强的标准偏差值,并对光谱中难以分辨的吸收谱线进行了分析。探测得到的最小谱线线强是4.3×10-27cm-1·(molcule·cm-2)-1,吸收谱线线强大于3.0×10-24cm-1·(mol·cm-2)-1由于吸收饱和而未被处理,同时所测得的光谱也显示出CH4分子在1.65μm附近有非常丰富的弱吸收谱线和复杂的结构。文中所报道的吸收谱线都是HITRAN2004数据库中所未报道的,而且也未见有其他文献报道过。     

基于量子级联激光器和长光程气室的甲烷传感器

根据中红外光谱吸收原理,利用甲烷(CH₄)气体分子在7.5 μm处的基频吸收特性,设计了一种基于量子级联激光器(QCL)和新型多反射长光程气体吸收气室(MPC)的甲烷气体传感器。该仪器使用了可进行热电冷却、工作在脉冲方式下、中心波长为7.5 μm的QCL,通过在室温条件下调节其注入电流(500 mA～1.6 A调节范围),其出射光波长可以扫过CH₄(1 332.8 cm-1)气体吸收线。同时使用了一种紧凑型MPC(40 cm长,800 mL采样容积),使得系统有效总光程达到16 m。此外,系统中使用了参考气室,并加入了空间滤波光学结构以满足MPC对入射光束的要求,配合差分吸收光谱检测原理,有效地改善了光束质量,降低了由光源波动引起的噪声,提高了仪器的检测灵敏度。通过对不同浓度的甲烷气体进行多次检测,该仪器的稳定性能良好,按信噪比为1计算,可实现对甲烷气体的检测下限为1 μmol·mol-1。     

The 2D Rancieite-type manganic acid and its alkali-exchanged derivatives: Part I — Chemical characterization and thermal behavior

The 2D Rancieite type manganic acid was prepared by reduction of KMnO₄ in acidic medium. Its ion exchange behavior allows to prepare alkali derivatives. All compounds were characterized with use of a combination of X-ray diffraction, chemical analyses, TGA, magnetic measurements and spectroscopic techniques. The evolution of their chemical composition versus temperature was studied between 180 and 400 °C. It shows that the dehydration process is partly reversible in these compounds whereas the weak reduction is irreversible. The 2D Rancieite-type manganic acid is readily different from a Birnessite-type phyllomanganate, as shown by several features: the interlayer distance, the ion exchange capacity, the thermal behavior, the interlayer cation content, the manganese average oxidation state, the magnetic behavior and the IR spectrum.     

How photocatalytic activity of the MAO-grown TiO2 nano/micro-porous films is influenced by growth parameters?

Pure titania porous layers consisted of anatase and rutile phases, chemically and structurally suitable for catalytic applications, were grown via micro-arc oxidation (MAO). The effect of applied voltage, process time, and electrolyte concentration on surface structure, chemical composition, and especially photocatalytic activity of the layers was investigated. SEM and AFM studies revealed that pore size and surface roughness of the layers increased with the applied voltage, and the electrolyte concentration. Moreover, the photocatalytic performance of the layers synthesized at medium applied voltages was significantly higher than that of the layers produced at other voltages. About 90% of methylene blue solution was decomposed after 180 min UV-irradiation on the layers produced in an electrolyte with a concentration of 10 g l⁻¹ at the applied voltage of 450 V.