化学修饰电极富集石墨炉原子吸收法测定痕量金

本文提出用聚丙烯脒硫氰酸盐化学修饰石墨管内壁、电化学预富集石墨炉原予吸收测定Au的分析方法.分析灵敏度提高100倍.应用于矿石中痕量Au的测定,获得了满意的结果.     

氟的离子选择电极瞬时电位法测定

研究了氟离子选择电极瞬时电位分析法，其检出限和Nernst响应下限均低于传统电位分析法，空白液切换到试液时瞬时电位达到稳定的峰电位Vp比传统电位法的响应快得多，可以实现小体积试液的快速准确分析；用该法测定了自来水和矿泉水中氟的含量；利用校正曲线的截距和检出限计算了LaF3的溶度积，在0.1mol/L KNO3介质中Ksp(LaF3)=10^-28.45，在0.001mol/L柠檬酸钠＋HAc-NaAc缓冲液（pH=5.50，离子强度I＝0.10mol/L)介质中溶度积K′sp(LaF3)=10^-26.26；据此，计算得柠檬酸与La^3 络合物的稳定常数K1=10^5.46和K2=10^3.99；用离子水合吉氏自由能ΔGh(F^-,g)解释了不同浓度F^-试液瞬时电位的跃迁时间。     

六氰合铁酸铜钴在蜡浸石墨电极表面的电化学沉积

首次报道了电化学沉积的混合金属六氰合铁酸盐修饰电极作为电流型传感器的研究。针对六氰合铁酸盐修饰电极在中性和碱性条件下的不稳定性，采用混合金属电沉积的方法，成功地提高了电极的稳定性，所得到的修饰电极在 ｐＨ ４～１０之间均表现出良好的稳定性。该电极的响应时间（ｔ９５％）为 ０．５ｓ，并对Ｆｅ３＋／Ｆｅ２＋电对表现出良好的电催化作用。催化氧化峰电流与Ｆｅ２＋的浓度在１．０×１０－４～６．５×１０－２ｍｏｌ/Ｌ范围内呈很好的线性关系，检测下限为 １．４×１０－６ｍｏｌ／Ｌ。     

以离子水合能解释离子选择电极响应机理

用相继切换不同浓度I^-试液的活度阶梯法研究了碘化银基离子选择电极（I^--ISE）的瞬时响应。随电位变化的离子水合自由能△Gh(I^-）显示出|△Gh（I^-）|越小，正活度阶民位跃迁越快而负活度阶梯电位变化越慢。将－△Gh(I^-）看作I（H2O）n^-与I^--ISE表面反应的活化能解释了这个现象。比起传统电位法，活度阶梯法的主要优点是ISEs响应非常快并且更灵敏，有可能实现小体积试液的快速分析。     

Pt电极上吸附原子对仲丁醇电催化氧化性能的影响

运用电化学循环伏安和石英晶体微天平研究了HClO4溶液中仲丁醇在Pt电极及以Sb和S吸附原子修饰的Pt(Pt/Sbad和Pt/Sad)电极上的电催化氧化过程 .从电极表面质量变化可以看出 ,仲丁醇的氧化与电极表面的氧物种有着极其密切的关系 .Pt电极表面Sb吸附原子可在较低的电位下吸附氧 ,明显提高仲丁醇的氧化活性 .与Pt电极相比 ,Sb吸附原子修饰的Pt电极使仲丁醇氧化的峰电位负移约 10 0mV .相反 ,Pt电极表面S吸附原子的氧化会消耗表面氧物种 ,抑制仲丁醇的氧化 .从电极表面质量变化提供了吸附原子电催化作用的数据     

直接乙醇燃料电池初探

采用商品化的PtRu/C和Pt/C分别作乙醇阳电极和氧气阴电极的催化剂 ,Nafion 115膜作固体电解质 ,组装成面积为 9cm2 的单池 .考察了电池温度、氧气压力、乙醇浓度及流量等对电池性能的影响 .实验结果表明在电池温度为 85℃ ,乙醇浓度为 1.0mol/L ,流量为 0 .5mL/min ,氧气压力为 0 .5MPa ,流量为 6 8mL/min条件下 ,电池开路电压为 0 .6 0 8V ,电流密度 5 0mA/cm2 时的放电端电压为 0 .32 9V ,电池最大功率密度为 19.2 5mW /cm2     

On-column polymer-imbedded graphite inlet electrode for capillary electrophoresis coupled on-line with flow injection analysis in a poly(dimethylsiloxane) interface

A method for coupling an electrophoretic driven separation to a liquid flow, using conventional fused-silica capillaries and a soft polymeric interface is presented. A novel design of the electrode providing high voltage to the electrophoretic separation was also developed. The electrode consisted of a conductive polyimide/graphite imbedded coating immobilized onto the capillary electrophoresis (CE) column inlet. This integrated electrode gave the same separation performance as a commonly used platinum electrode. The on-column electrode also showed good electrochemical stability in chronoamperometric experiments. In addition, with this electrode design, the electrode position relative to the inlet end of the CE column will always be constant and well defined. The on-line flow injection analysis (FIA)-CE system was used with electrospray ionization (ESI)-time of flight (TOF)-mass spectrometry detection. The preparation of the PDMS (poly(dimethylsiloxane)) interface for FIA-CE is described in detail and used for initial tests of the on-column polymer-imbedded graphite inlet electrode. In this interface, a pressure-driven liquid flow, a make up CE electrolyte and a CE column inlet meet in a two-level cross (95 microm ID) in the PDMS structure, enabling independent flow characterization.     

Microdevices for manipulation and accumulation of micro- and nanoparticles by dielectrophoresis

Microfluidic devices with three-dimensional (3-D) arrays of microelectrodes embedded in microchannels have been developed to study dielectrophoretic forces acting on synthetic micro- and nanoparticles. In particular, so-called deflector structures were used to separate particles according to their size and to enable accumulation of a fraction of interest into a small sample volume for further analysis. Particle velocity within the microchannels was measured by video microscopy and the hydrodynamic friction forces exerted on deflected particles were determined according to Stokes law. These results lead to an absolute measure of the dielectrophoretic forces and allowed for a quantitative test of the underlying theory. In summary, the influence of channel height, particle size, buffer composition, electric field, strength and frequency on the dielectrophoretic force and the effectiveness of dielectrophoretic deflection structures were determined. For this purpose, microfluidic devices have been developed comprising pairs of electrodes extending into fluid channels on both top and bottom side of the microfluidic channels. Electrodes were aligned under angles varying from 0 to 75 degrees with respect to the direction of flow. Devices with channel height varying between 5 and 50 microm were manufactured. Fabrication involved a dedicated bonding technology using a mask aligner and UV-curing adhesive. Particles with radius ranging from 250 nm to 12 microm were injected into the channels using aqueous buffer solutions.     

Fabrication, Characterization and Electrocatalysis of an Ordered Carbon Nanotube Electrode

A method for fabrication of ordered carbon nanotube (CNT) film,which was template-synthesized within the highly ordered pores of a commercially available alumina template membrane,modified glassy carbon(CNT/GC) electrode was established.The CNT/GC electrode showed excellent electrocatalytic activity toward dopamine electrochemical reaction without introducing any electrochemically active group into CNT film or activating any electrochemically active group into CNT film or activating the electrode electrochemically.DA undergoes ideal reversible electrochemical reaction on CNT/GC electrode at low scan rate(≤20mV/s) with an excellent reproducibility and stability.The CNT/GC electrode might be used in biosensors because the highly ordered CNT may present a steric effect on more efficient redox reactions of biomolecules.