Flux decline behaviors in dead-end microfiltration of activated sludge and its supernatant

The properties of dead-end microfiltration were explored under constant pressure using two types of activated sludge controlled under the condition of different air flow rates. The activated sludge cultured at the air flow rate of 0.15 L min⁻¹ (the anaerobic condition) exhibited a significant flux decline compared with the case of the air flow rate of 2.33 L min⁻¹ (the aerobic condition). It was found from the results of microfiltration of the supernatant separated by centrifugation that the constituents in the supernatant caused a major cake resistance in microfiltration of the activated sludge. The average specific filtration resistance for filtration of the activated sludge was closely consistent with that for filtration of the supernatant at low pressure (49 kPa). However, the cake resistance of the microbial floc in microfiltration of the activated sludge became substantial with increasing filtration pressure because of high compressibility of the microbial floc. Moreover, the foulant and the fouling mechanism in microfiltration of the supernatant were evaluated from both microfiltration test of the supernatant and microfiltration test of the filtrate collected thereby. As a result, the effects of the pore size and material of the microfiltration membrane on the flux decline behaviors in dead-end microfiltration were reasonably elucidated.     

Profiling and comprehensive expression analysis of ABC transporter solute-binding proteins of Bacillus subtilis membrane based on a proteomic approach

We analyzed ABC transporter solute-binding proteins (SBPs) of the Bacillus subtilis membrane using a proteomic approach. We prepared a washed cell membrane fraction that was insoluble in 134 mM nondetergent sulfobetaine and then extracted proteins using mixtures of detergents in a stepwise manner. The membrane proteins were resolved by three two-dimensional polyacrylamide gel electrophoresis (2-D PAGE) or two one-dimensional (1-D) PAGE procedures, electroblotted, and digested in the presence of 5% or 80% acetonitrile. Thereafter, matrix-assisted laser desorption/ionization-time of flight-mass spectrometry (MALDI-TOF MS) identified 637 proteins corresponding to 15.9% of the total cellular proteins. We predicted that among these, 256 were membrane proteins, 101 were lipoproteins or secretory proteins and 280 were soluble proteins containing peripheral proteins that function in both the cytoplasm and the cell membrane such as SecA and FtsY. Among the 637 proteins, we identified 30 SBPs among 38 importers predicted by a bioinformatic search of the genome. We confirmed expression of the genes for the 30 SBPs using DNA microarray analysis. We compared the 2-D gel separation profiles of submembrane fractions solubilized by 1% n-dodecyl-beta-D-maltoside from cells cultured on Luria Bertani (LB), S7, and S7 medium without glutamate as well as DNA microarray data on LB and S7. The results suggested that YcdH, YtmK and YurO are binding proteins for Mn(++), glutamate and glucose, respectively, and that YqiX and YxeM are binding proteins for amino acids (tryptophan in S7 medium).     

Novel Ytterbium(III) Selective Membrane Sensor Based on N‐(2‐Pyridyl)‐N′‐(2‐Methoxyphenyl)‐Thiourea as an Excellent Carrier and Its Application to Determination of Fluoride in Mouth Wash Preparation Samples

The construction, performance, and applications of a novel ytterbium(III) sensor based on N‐(2‐pyridyl)‐N′‐(2‐methoxyphenyl)‐thiourea (PMT), as an excellent carrier, in plasticized poly(vinyl chloride) PVC matrix, is described. The influences of membrane composition and pH on the potentiometric response of the sensor were investigated. The sensor exhibits a nice Nernstian response for Yb(III) ion over a wide concentration range of 4 decades of concentration (1.0×10^?6–1.0×10^?2 M), and a detection limit of 5.0×10^?7 M. The response time of the electrodes is between 8 and 10 s, depending on the concentration of ytterbium(III) ions. The proposed sensor can be used for about 8 weeks without any considerable divergence in potential. The sensor revealed very good selectivity for Yb(III) in the presence of several metal ions. The best performance was observed for the membrane containing; 30% PVC, 59% o‐nitrophenyloctyl ether (NPOE) as solvent mediator, 7% PMT, and 4% sodium tetraphenyl borate (NaTPB). It was successfully applied as indicator electrodes in the potentiometric titration of Yb(III) with EDTA and for the determination of fluoride ion in two mouth wash formulations. The proposed La(III) sensor was found to work well under laboratory conditions. It was also used as an indicator electrode in titration of a 1.0×10^?4 M of Yb(III) with a standard EDTA solution (1.0×10^?2 M). It was also used for determination of Yb(III) ion in Xenotime .     

Cyclic voltammetry of highly hydrophilic ions at a supported liquid membrane

Cyclic voltammetry has been used to study the coupling of ion transfer reactions at a liquid membrane. The liquids are either supported by a porous hydrophobic membrane (polyvinylidene difluoride, PVDF) when the organic solvent is non-volatile (o-nitrophenyloctylether) or are merely a free standing organic solvent layer such as 1,2-dichloroethane comprised between two hydrophilic dialysis membranes supporting the adjacent aqueous phases. The passage of current across the liquid membrane is associated with two ion transfer reactions across the two polarised liquid liquid interfaces in series. It is shown that it is possible to study the transfer of highly hydrophilic ions at one interface by limiting the mass transfer of the other ion transfer reaction at the other interface. Indeed, for systems comprising an ion M in one aqueous phase and a reference ion R partitioned between the membrane and the other aqueous phase, the observed and simulated cyclic voltammograms have a half-wave potential determined by the Gibbs energy of transfer of M transferring at one interface and by the limiting mass transfer of R at the other interface. This new methodology opens a way to measure the Gibbs energy of transfer of highly hydrophilic or hydrophobic ions, which usually limits the potential window at single liquid liquid interfaces (ITIES).     

Photolithographically patternable nitrate-sensitive acrylate-based membrane

A photocurable acrylate matrix nitrate-sensitive membrane containing 2-nitrophenyl n-octyl ether as mediator and tetraalkylammonium nitrate as an active compound is described. The photocuring was achieved by the use of photoinitiators containing diaryliodonium chloride. This acrylate membrane is patternable via a photolithographic process with a only slight loss of electrochemical characteristics.     

Preparation, characterization and effect of annealing on performance of cellulose acetate/sulfonated polysulfone and cellulose acetate/epoxy resin blend ultrafiltration membranes

Polymeric membranes based on cellulose acetate (CA)--sulfonated polysulfone blends at three different polymer compositions were prepared by solution blending and phase inversion technique, characterized and subjected to annealing at 70, 80 and 90 °C. The permeate water flux, separation of bovine serum albumin and its flux by the blend membranes before and after thermal treatment, have been compared and discussed. Similarly, CA and epoxy resin (diglycidyl ether of bisphenol-A) were blended in various compositions, in the presence and in the absence of polyethyleneglycol 600 as non-solvent additive, using N,N^′-dimethylformamide as solvent, and used for preparing ultraflltration membranes by phase inversion technique. The polymer blend composition, additive concentration, casting and gelation conditions were optimized. Blend membranes were characterized in terms of compaction, pure water flux, water content and membrane resistance. The effects of polymer blend composition and additive concentration on the above parameters were determined and the results are discussed.     

XPS STUDIES ON SURFACE MODIFIED POLY [1-(TRIMETHYLSILYL)-1-PROPYNE] MEMBRANES Ⅱ SURFACE MODIFICATION BY BROMINE VAPOR*

Surface modification of poly [1-(trimethylsilyl)-1-propyne] (PTMSP) membranes bybromine vapor has been studied. It is shown that Br/C atomic ratio at the surfaces increased withthe time of bromination until about 60 min, then it reached a plateau. The results of XPS and IRstudies indicated that the addition of bromine to double bonds and the replacement of H on CH_3 bybromine had taken place so that a new peak at 286.0 eV (C--Br)in C_(1s) spectra and some newbands, e. g. at 1220 and 580cm~(-1) in IR spectra were formed. The fact,t Po_2, permeability ofoxygen, decreased and α_(O_2/N_2), separation factor of oxygen relative to nitrogen, increased withbromination time, shows that surface modification of PTMSP by bromine may be an efficient approach to prepare PTMSP membranes used for practical gas separations.     

Long-term study of an intermittent air sparged MBR for synthetic wastewater treatment

Membrane bioreactors (MBR) combine biological processes with membrane filtration. Advantages of MBR in municipal wastewater treatment include high effluent quality and reduced space requirements. Steady operation of membrane plants requires careful management of membrane fouling. Even though it might be impossible to prevent, fouling can be limited by techniques such as gas sparging. The injection of gas bubbles increases the shear stress and removes fouling material from the membrane surface. Most cited literature on air sparging refers to short-term experiments, often times in bench scale. The aim of this study was therefore long-term investigations in pilot plant scale of a 70 L reactor fed with glucose-based synthetic wastewater. The main focus was on enhancing permeate flux by air sparging. The results showed that using air sparging significantly increased the permeate flux was doubled even over several weeks. The findings were interpreted using the dimensionless fouling and shear stress number. The fouling resistance was found to decrease significantly with air injection ratios between 0.4 and 0.5. When air sparging was applied after a period without air sparging, the shear stress number doubled. This increase in shear led to a reduction of the fouling number by approximately 30%. During several weeks air sparging only a slow fouling number increase was. In contrast to that after air sparging was ceased, an exponential increase of the fouling number was observed.     

Carotenoid incorporation into microsomes: yields, stability and membrane dynamics

The carotenoids beta-carotene (BC), lycopene (LYC), lutein (LUT), zeaxanthin (ZEA), canthaxanthin (CTX) and astaxanthin (ASTA) have been incorporated into pig liver microsomes. Effective incorporation concentrations in the range of about 1-6 nmol/mg microsomal protein were obtained. A stability test at room temperature revealed that after 3 h BC and LYC had decayed totally whereas, gradually, CTX (46%), LUT (21%), ASTA (17%) and ZEA (5%) decayed. Biophysical parameters of the microsomal membrane were changed hardly by the incorporation of carotenoids. A small rigidification may occur. Membrane anisotropy seems to offer only a small tolerance for incorporation of carotenoids and seems to limit the achievable incorporation concentrations of the carotenoids into microsomes. Microsomes instead of liposomes should be preferred as a membrane model to study mutual effects of carotenoids and membrane dynamics.     

Electrokinetic characterization of a microporous non-commercial polysulfone membrane: phenomenological coefficients and transport parameters

Electrical and electrokinetic phenomena (electrical resistance, streaming potential and membrane potential) in a porous polysulfone membrane was studied in the framework of the linear thermodynamics of irreversible processes and the phenomenological coefficients were determined for different concentrations of NaCl and MgCl₂ solutions (10⁻³M<5×10⁻²M). From experimental values, other characteristic membrane parameters such as the concentration of fixed charge in the membrane (=−3×10⁻³M), the ionic transport numbers and permeabilities through the membrane (t(Na⁺)=0.392 and t(Mg⁺²)=0.363; P(Na⁺)=3.5×l0⁻⁸m/sec and P(Mg⁺²)=2.9×10⁻⁸m/sec) were also obtained. Membrane surface-electrolyte solution interface was characterized by zeta potential values. The effect of both salt concentration and pH on zeta potential results was also studied.