Influence of annealing and chain defects on the melting behaviour of poly(vinylidene fluoride)

The melting behaviour of poly(vinylidene fluoride) (PVDF) was investigated by differential scanning calorimetry (DSC) and small- and wide-angle X-ray scattering in order to study the influence of the chain defects content and of the temperature of annealing on the crystallization and melting behaviour.All the DSC scans show a double endotherm and the analysis of the data suggests that the low temperature endotherm is due to the melting of a population of thin lamellae, whose thickness increases during the annealing, but a high content of chain defects prevents the lamellar thickening and the main effect in this case is the crystallization of thin lamellae from a portion of polymer which did not crystallize during the quenching from the melt. Furthermore, the two melting endotherms, which are observed, can be partially ascribed to a melting-recrystallization process.Furthermore, stepwise isothermal cooling was performed in a differential scanning calorimeter followed by melting scans of fractionated PVDF samples to point out the possible presence of a series of endothermic peaks.     

γ-射线辐照对尼龙6纤维结构的影响

<正> 过去的大多数研究表明,高能射线辐照会引起聚乙烯及聚丙烯等稀烃类聚合物分子链交联及降解,而且会导致结晶度下降。张利华等人最近的研究表明,对于尼龙1010塑料,仅当辐照剂量高到一定程度后,辐照才会破坏结晶。此外,Stowe等人曾经研究过近紫外线对尼龙66纤维结构的影响,结果表明,在空气气氛中的近紫外辐照主要导致尼龙66纤维降解,并使纤维结晶度提高。有关高能射线辐照对高度取向的合成纤维结构及性能的影响的研究尚不多见。本工作将讨论γ-射线对于尼龙6纤维结构的影响。     

含间苯基聚芳醚酮的合成与性能研究

含间苯基聚芳醚酮的合成与性能研究林权，张万金，吴忠文，尹玖梅（吉林大学化学系，长春，１３００２１）（中国科学院长春应用化学研究所）关键词聚芳醚酮，间苯基，熔点，结晶度聚芳醚酮作为一类耐高温特种工程塑料，由于具有优异的热、电、机械性能，已被广泛应用于电...     

Poly(butylene terephthalate)/poly(ε-caprolactone) blends: Influence of PCL molecular mass on PBT melting and crystallization behavior

The isothermal crystallization kinetics and melting behavior of poly(butylene terephthalate) (PBT) in binary blends with poly(ε-caprolactone) (PCL) was investigated as a function of PCL molecular mass by differential scanning calorimetry and optical microscopy. The components are miscible in the melt when oligomeric PCL (M_w = 1250) is blended with PBT, whereas only partial miscibility was found in mixtures with higher molecular mass (M_w = 10,000 and 50,000). The equilibrium melting point of PBT in the homopolymer and in blends with PCL was determined through a non-linear extrapolation of the T_m = f(T_c) curve. The PBT spherulitic growth rate and bulk crystallization rate were found to increase with respect to plain PBT in blends with PCL1250 and PCL10000, whereas addition of PCL50000 causes a reduction of PBT solidification rate. The crystallization induction times were determined by differential scanning calorimetry for all the mixtures through a blank subtraction procedure that allows precise estimation of the crystallization kinetics of fast crystallizing polymers. The results have been discussed on the basis of the Hoffman-Lauritzen crystallization theory and considerations on both the transport of chains towards the crystalline growth front and the energy barrier for the formation of critical nuclei in miscible and partially miscible PBT/PCL mixtures are widely debated.     

Thermal transitions of DODAB vesicular dispersions

Two endothermic transitions, at 36°C and 44°C, were observed with differential scanning calorimetry (DSC) upon heating dioctadecyldimethylammonium bromide vesicle dispersions that were equilibrated below 15°C while in samples kept at 25°C there was only the transition at 44°C, which was shown to be the gel to liquid–crystalline transition by ¹H-NMR measurements. The transition at 36°C was reversed in an exothermic transition around 13°C upon cooling. The slowness of this transition at ambient temperatures suggests that the presence of the transition at 36°C in a DSC upscan depends strongly on the sample history.     

Characteristics of major dioxin/furan congeners in melted slag of ash from municipal solid waste incinerators

Polychlorinated dibenzo-p-dioxins (PCDDs) and polychlorinated dibenzofurans (PCDFs) in slag of fly ash from three municipal solid waste (MSW) incinerators were analyzed to observe any changes in characteristics and distribution of their congeners by melting process. Actual concentration and Toxic Equivalent (TEQ) concentration profiles of 17 major congeners of PCDDs/PCDFs for gas, fly ash and melted slag were compared. The distributions of PCDDs/PCDFs in different streams macroscopically showed similarities with the generally known profiles for emission gas from a municipal waste incinerator. The total concentrations of PCDDs/PCDFs in off-gas and fly ash have been known to be a function of incineration conditions and of air pollution control device utilization; however, their normalized distributions were independent of such conditions. The concentrations of PCDDs/PCDFs in the melted slag of fly ash were not related to the concentrations of PCDDs/PCDFs congeners in fly ash but were rather a function of the melting furnace type and operation. The total amount of PCDDs/PCDFs in the melted slag of fly ash contained almost 150–27,000 times less dioxin than that in fly ash, however, the TEQ of dioxin in the slag was reduced by 435–43,500 times, which could enable them to be utilized as recycled construction materials. In normalized TEQ concentration profiles of 17 congeners of PCDDs/PCDFs, the ratio of PCDFs to PCDDs changed from 1.32 to 2.19 by melting, which showed relatively higher portion of furans left in melted slag than those in fly ash. By comparing reduction ratios of different congeners, PCDDs (dioxins) were relatively easier to destruct than PCDFs (furans) during melting process. The most difficult congener to destruct could be octa-chlorinated dibenzofuran (OCDF) among major congeners. For slag cooling methods, dioxin concentration in TEQ of slow cooled slag by air was four times higher than that of fast cooled slag by water. Thus cooling by water is more appropriate with the added beneficial effect of producing granules/particles, which can be utilized as roadbed materials.     

Equations describing lamellar structure parameters and melting points of polyethylene-<Emphasis Type="Italic">co</Emphasis>-(butene/octene)s

Time- and temperature-dependent SAXS-experiments were used to determine the effect of octene and butene co-units on the lamellar structure and the melting properties of polyethylene. As expected, melting points decrease with increasing co-unit content, but crystal thicknesses are not affected and depend on the crystallization temperature only. Results can be cast into some simple equations which describe the dependence:

面心立方C60表面过程的计算机模拟

近年来发现的C60及其金属掺杂化合物形成一个新的材料族，其半导体性质、超导性质及非线性光学性质已受到广泛注意，但目前对这类材料的表面性质尚缺乏研究，我们曾采用参数化的Lenard－Jones6－12模型函数比较不同晶型C6o的相对稳定性　[1]，预测面心立方C60（FccC60）的声子散射频率和态密度[2]，并计算其表面能[3]，取得有意义的结果，表明这一简单模型势能函数是C60分子间有效范德华作用的一种合理抽提．本工作进一步将该势能函数应用于研究fccC60表面吸附分子的迁移机理，并用蒙特卡罗方法模拟fcC（110）及（100）晶面的熔化过程，…     

Selective water sorbents for multiple applications, 3. CaCl2 solution confined in micro- and mesoporous silica gels: Pore size effect on the “solidification-melting” diagram

In this communication we present a low-temperature “solidification-melting” phase diagram for CaCl₂/H₂O solutions confined in KSK and KSM silica gels. At salt concentrations of 0–48 wt. %, the diagram has been found to lie below the diagram reported for the bulk system by 15–30°C. It shows a depression of the solution melting point due to its confinment to the pores. Several other peculiarities of melting and solidification in this system are also reported and discussed. Beside fundamental interest, the data obtained could be of importance in many commercial areas such as refrigeration, accumulation of low temperature heat, frost prevention in building materials,etc.