57Fe Mössbauer spectroscopic study of (25−x)MnO–xZnO–15Fe2O3–60B2O3 glasses

The ⁵⁷Fe Mössbauer technique has been used to investigate the effect of zinc oxide substitution in (25???x)MnO–xZnO–15Fe₂O₃–60B₂O₃ glass system (x?=?0, 5, 10, 15 and 20 mol% of ZnO ). Mössbauer absorption spectra for all the samples recorded at room temperature suggest the existence of the two paramagnetic quadrupole doublets. The observed variations in hyperfine parameters have been explained on the basis of cations distribution and exchange interaction at the lattice sites and it is concluded that B–B interaction increases while the metal–metal interaction decreases due to replacement of manganese oxide by zinc oxide. These results suggest that the present glass system exhibits a paramagnetic behaviour that changes towards the weak paramagnetic when manganese oxide was replaced with zinc oxide.     

Fabrication and characterization of sputtered titanium dioxide films

TiO₂ thin films were prepared under various conditions by using a reactive RF sputtering technique. The structural, optical and electrical characteristics of the films have been investigated. All as-deposited films were amorphous. After annealing at T > 673 K, the crystallinity of the observed tetragonal anatase phase appeared improved. The optical band gap, determined by using Tauc plot, has been found to amount to 3.38 ± 0.03 and 3.21 ± 0.03 eV for the direct and indirect transition, respectively. Also the complex optical constants for the wavelength range 300-2500 nm are reported. Using the two-point probe technique, the dark resistivity has been measured as a function of the film thickness, d. The resistivity, ρ, of the samples has been found to decrease markedly with increasing thickness, but only for d < 100 nm. The behaviour of ρd versus d was found to fit properly with the Fuchs and Sondheimer relation with parameters ρ_o = 4.95 × 10⁶ Ω cm and mean free path, l = 310 ± 2 nm. The log ρ versus 1/T curves show three distinct regions with values for the activation energy of 0.03 ± 0.01, 0.17 ± 0.01 and 0.50 ± 0.02 eV, respectively.     

0.18μm CMOS工艺栅极氧化膜可靠性的衬底和工艺依存性

用斜坡电压法(Voltage Ramp, V-ramp)评价了0.18μm双栅极 CMOS工艺栅极氧化膜击穿电量(Charge to Breakdown, Q_bd)和击穿电压(Voltage to Breakdown, V_bd). 研究结果表明，低压器件(1.8V)的栅极氧化膜(薄氧)p型衬底MOS电容和N型衬底电容的击穿电量值相差较小，而高压器件(3.3V)栅极氧化膜(厚氧)p衬底MOS电容和n衬底MOS电容的击穿电量值相差较大，击穿电压测试值也发现与击穿电量 关键词： 薄氧 可靠性 击穿电压 击穿电量     

Friedel-Crafts alkylation of indoles with epoxides catalyzed by nanocrystalline titanium(IV) oxide

Friedel-Crafts alkylation of indoles with epoxides to afford 3-alkyl indole derivatives at room temperature with moderate to good yields and high regioselectivity using nanocrystalline titanium(IV) oxide catalyst is described.     

The effect of ITO films thickness on the properties of flexible organic light emitting diode

Indium tin oxide (ITO) thin films were deposited on cyclic olefin copolymer substrate at room temperature by an inverse target sputtering system. The crystal structure and the surface morphology of the deposited ITO films were examined by X-ray diffraction and atomic force microscopy, separately. The electrical properties of the conductive films were explored by four-point probing. Visible spectrometer was used to measure the optical properties of ITO-coated films. The performance of the flexible organic light emitting diode device with different thickness anode was investigated in this study.     

Photo-Absorption and photochemical decomposition of copper and alkaline-earth ß-diketonates as source gases of high-Tc superconducting films

For low-temperature deposition of oxide films relating to Bi-Sr-Ca-Cu-O superconductors, photo-absorption and -decomposition properties were examined with respect to copper and alkaline-earth ß-diketonates. It was confirmed that all ß-diketonates examined were promising as source materials for photochemical vapour deposition (photo-CVD) using a low-pressure mercury lamp, in view of their large light absorption coefficients at wavelength 254 nm. The light irradiation was effective for the formation of highly crystalline oxide films at temperatures below 600 °C. By combining two sources, Ca₂CuO₃ and SrCuO₂ films were prepared. Photo-CVD of c-axis oriented Bi₂Sr₂CuO_x film was achieved by the irradiation of ternary sources of Bi(C₆H₅)₃ and strontium and copper ß-diketonates at 500 °C.     

Alloy formation in mechanically activated mixtures

The physical mixtures of hydroxocarbonates of Cu and Ni with aluminium were activated using a laboratory planetary mill. The chemical reactions and alloy formations as the effects of grinding were followed by the phase analysis of solid products based on the thermogravimetry and X-ray diffractometry. Experimental evidence indicates that the nature of reactions and products of mechanical activation was dependent on the amount of aluminium and time of grinding. This revised version was published online in July 2006 with corrections to the Cover Date.     

Combinatorial computational chemistry approach of tight-binding quantum chemical molecular dynamics method to the design of the automotive catalysts

Recently, we have developed a new tight-binding quantum chemical molecular dynamics program “Colors” for combinatorial computational chemistry approach. This methodology is based on our original tight-binding approximation and realized over 5000 times acceleration compared to the conventional first-principles molecular dynamics method. In the present study, we applied our new program to the simulations on various realistic large-scale models of the automotive three-way catalysts, ultrafine Pt particle/CeO₂(111) support. Significant electron transfer from the Pt particle to the CeO₂(111) surface was observed and it was found to strongly depend on the size of the Pt particle. Furthermore, our simulation results suggest that the reduction of the Ce atom due to the electron transfer from the Pt particle to the CeO₂ surface is a main reason for the strong interaction of the Pt particle and CeO₂(111) support.     

A Mössbauer spectroscopic study of an industrial catalyst for dehydrogenation of etylbenzene to styrene

Iron oxide catalyst with spinel structure used for dehydrogenation of ethylbenzene is one kind of important catalyst in petrochemical industry. In this work several series of industrial catalyst were prepared with different components and different manufacturing processes. Mössbauer Spectroscopy has been used to determine the optimal components and the better manufacturing process for spinel structure formation. The results may prove useful for producing the industrial dehydrogenation catalyst with better catalytic property.     

Synthesis of perfluoroheptanal by ozonolysis of perfluoro-1-octene

Perfluoro-1-octene was used as a model for developing a method for the preparative ozonolysis of perfluoro-1-alkenes to the corresponding perfluoro-nor-alkenals. Perfluoroheptanal was synthesized.Translated fromIzvestiya Akademii Nauk. Seriya Khimicheskaya, No. 6, pp. 1146–1147, June, 1994.