Structural and electrical properties of crystalline (1−x)Ta2O5−xTiO2 thin films fabricated by metalorganic decomposition

Polycrystalline (1−x)Ta₂O₅−xTiO₂ thin films were formed on Si by metalorganic decomposition (MOD) and annealed at various temperatures. As-deposited films were in the amorphous state and were completely transformed to crystalline after annealing above 600 °C. During crystallization, a thin interfacial SiO₂ layer was formed at the (1−x)Ta₂O₅−xTiO₂/Si interface. Thin films with 0.92Ta₂O₅–0.08TiO₂ composition exhibited superior insulating properties. The measured dielectric constant and dissipation factor at 1 MHz were 9 and 0.015, respectively, for films annealed at 900 °C. The interface trap density was 2.5×10¹¹ cm⁻² eV⁻¹, and flatband voltage was −0.38 V. A charge storage density of 22.8 fC/μm² was obtained at an applied electric field of 3 MV/cm. The leakage current density was lower than 4×10⁻⁹ A/cm² up to an applied electric field of 6 MV/cm.     

Synthesis of poly-yne polymers containing transition metals,disilane, disiloxane and phosphine groups in the main chain

The synthesis and characterization of metal poly-yne polymers containing disilane, disiloxane and phosphine groups in the main chain are described. The platinum and palladium poly-yne polymers were synthesized by polycondensation reactions between a metal chloride and an α, ω-bisethynyl complex in amines in the presence of cuprous iodide as a catalyst. The nickel poly-yne polymers were synthesized by an alkynyl ligand exchange reaction between a nickel acetylide and an α, ω-bisethynyl complex in diethylamine in the presence of cuprous iodide as a catalyst. The reaction of the platinum poly-yne polymer, containing disiloxane groups in the main chain, with copper (I) salts afforded adducts of η-²-bonded σ-acetylide polymer complexes. The reactions of the palladium poly-yne polymer, containing phosphine groups in the main chain, with transition-metal carbonyl complexes afforded polymer complexes which have phosphorus in the main chain-transition-metal bonds. A concentrated solution of the platinum poly-yne polymer containing disiloxane groups in the main chain forms a lyotropic liquid crystal in dichloromethane or 1, 2-dichloroethane.     

Synthesis and characterization of norbornene–ethylene–styrene terpolymers with a substituted ansa‐fluorenylamidodimethyltitanium‐based catalyst

This article reports a synthetic method for a norbornene–ethylene–styrene (N‐E‐S) terpolymer, which has not been well investigated so far, via incorporation of styrene (S) into vinyl‐type norbornene–ethylene (N‐E) copolymers catalyzed by a substituted ansa‐fluorenylamidodimethyltitanium [Me₂Si(3,6‐tBu₂Flu)(tBuN)]TiMe₂ catalyst ( I ) activated with a [Ph₃C][B(C₆F₅)₄]/Al(iBu)₃ cocatalyst at room temperature in toluene. The resulting terpolymerization product contained the targeted N‐E‐S terpolymer and the contaminated homopolymers, which were then able to be completely removed by solvent fractionation techniques. While homopolystyrene was easily extracted by fractionation with methylethylketone as a soluble part, homopolyethylene and a trace amount of homopolynorbornene could be perfectly separated by fractionation with chloroform as insoluble parts. The detail characterizations of a chloroform‐soluble polymer with gel permeation chromatography, nuclear magnetic resonance, and differential scanning calorimetry analyses proved that it contained a true N‐E‐S terpolymer with long N‐E sequences incorporated with isolated or short styrene sequences. The homogeneity of the morphology together with a single glass transition temperature that proportionally decreased with the increase of the styrene contents indicated that the N‐E‐S terpolymer obtained in this work is a random polymer with an amorphous structure. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 2765–2773, 2007     

Tuning size and catalytic activity of nano-clusters of cobalt oxide

Cobalt oxides were prepared by three different methods: (1) by reacting cobalt nitrate with oxalic acid, (2) co-precipitating cobalt nitrate with sodium carbonate, and (3) using sodium dodecyl sulphate as organic surfactant. All three samples were characterized before and after calcination by solvent extraction and the resulting products examined by IR spectroscopy. In the case of method 3, the removal of surfactant was followed by TGA studies. Products from all three methods were identified by XRD. Peaks in low angle XRD indicate the porous nature of the oxides. The morphology of the pores was studied by transmission electron microscopy. Some irregular pore structures were obtained for samples from methods 1 and 2, with an average size of 4–6 nm. Only the product from method 3 using SDS as template showed ordered structure and optimum size, and Brunauer-Emmet-Teller surface areas of the as-prepared, as well as the treated samples, exhibited H3 type hysteresis. The samples from the three methods were used as catalysts in the oxidation reaction of cyclohexane under mild conditions and the catalytic efficiency of the cobalt oxide was comparable with mesoporous cobalt oxides.     

Orientation and relaxation of polymer–clay solutions studied by rheology and small-angle neutron scattering

The influence of shear on viscoelastic solutions of poly(ethylene oxide) (PEO) and clay [montmorillonite, i.e., Cloisite NA+ (CNA)] was investigated with rheology and small-angle neutron scattering (SANS). The steady-state viscosity and SANS were used to measure the shear-induced orientation and relaxation of the polymer and clay platelets. Anisotropic scattering patterns developed at much lower shear rates than in pure clay solutions. The scattering anisotropy saturated at low shear rates, and the CNA clay platelets aligned with the flow, with the surface normal parallel to the gradient direction. The cessation of shear led to partial and slow randomization of the CNA platelets, whereas extremely fast relaxation was observed for laponite (LRD) platelets. These PEO–CNA networklike solutions were compared with previously reported PEO–LRD networks, and the differences and similarities, with respect to the shear orientation, relaxation, and polymer–clay interactions, were examined. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 3102–3112, 2004     

Thickness of a silica-tethered poly(ethylene oxide) layer measured by spin labeling

EPR spectroscopy of labeled poly(ethylene oxide) (PEO) grafted on silica has been used to characterize the conformation and local dynamics of the chains. Grafted molecules of MW 2000 with grafting ratios of 0.045, 0.057, 0.126, and 0.42 molecules/nm² were in contact with benzene. The mobility of the label was compared with that observed for solution of PEO from very diluted to highly concentrated and even bulk PEO. Thus, the concentration inside the grafted layer could be evaluated and also the thickness, which evolves rather linearly with the grafting ratio. © 1995 John Wiley & Sons, Inc.     

Palladium-catalyzed C-N bond formation: synthesis of 1-aryl-1H-pyrazoles from β-bromovinyl aldehydes and arylhydrazines

Cyclic and acyclic β-bromovinyl aldehydes are cyclized with an array of arylhydrazines in toluene at 125 °C in the presence of a palladium catalyst and a phosphorus chelating ligand together with NaO^tBu to give 1-aryl-1H-pyrazoles in moderate to good yields.     

A comparative XPS and UPS study of VOx layers on mineral TiO2(001)‐anatase supports

Four vanadium oxide layers on mineral TiO₂(001)‐anatase supports with different thickness (3–33 Å) were prepared with reactive d.c. magnetron sputtering and were extensively studied with photoelectron spectroscopy. Al Kα radiation and 150 eV synchrotron radiation were used as excitation sources. The evolution of the 2p, 3s and 3p core level line shapes of V and Ti as a function of the vanadium oxide thickness was studied, as well as the O1s and O2s core lines and the valence band. All the V2p spectra of the deposited vanadium oxide layers consist of at least 60% V⁵⁺, the rest being V⁴⁺. The V3p region is complicated by multiplet splitting, which prevents the determination of the vanadium oxidation state. The V3p multiplet splitting is different for the two excitation energies. No reduction of the titania support surface due to the vanadium oxide deposition was observed. Copyright © 2006 John Wiley & Sons, Ltd.     

Pd (II)‐catalyzed vinyl addition polymerization of novel functionalized norbornene bearing dimethyl carboxylate groups

Three novel functionalized polynorbornenes (PNB) with pendant dimethyl carboxylate group (carboxylates—acetate, propionate, and butyrate) are synthesized as a vinyl‐type with a palladium (II) catalyst in high yield. The effects of size of substitutents, molar ratio of monomer to catalyst, solvent polarity, reaction time, and temperature on the polymerization of exo‐norbornene dimethyl propionate were systematically investigated. The low molar ratio and temperature, as well as high polarity of solvent, and long reaction time, are favorable for the enhancement of the monomer conversion, especially, the solvent have an obvious effect on the catalyst activity. The resulting poly(cis‐norbornene‐exo‐2,3‐dimethyl carboxylates) (PNB‐dimethyl carboxylates) show good solubility in common organic solvent and high thermal stability up to 360 °C. The glass transition temperature was detected by DMA at 331, 324, and 318 °C for acetate, propionate, and butyrate, respectively. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 3391–3399, 2007     

Heterograft copolymers of poly(ε‐caprolactone) prepared by combination of ATRA “grafting onto” and ATRP “grafting from” processes

This paper aims at reporting on the synthesis of a heterograft copolymer by combining the “grafting onto” process based on atom transfer radical addition (ATRA) and the “grafting from” process by atom transfer radical polymerization (ATRP). The statistical copolymerization of ε‐caprolactone (εCL) and α‐chloro‐ε‐caprolactone (αClεCL) was initiated by 2,2‐dibutyl‐2‐stanna‐1,3‐dioxepane (DSDOP), followed by ATRA of parts of the chlorinated units of poly(αClεCL‐co‐εCL) on the terminal double bond of α‐MeO,ω‐CH₂?CH? CH₂? CO₂‐poly(ethylene oxide) (PEO). The amphiphilic poly(εCL‐g‐EO) graft copolymer collected at this stage forms micelles as supported by dynamic light scattering (DLS) and transmission electron microscopy (TEM). The unreacted pendant chloro groups of poly(εCL‐g‐EO) were used to initiate the ATRP of styrene with formation of copolymer with two populations of randomly distributed grafts, that is PEO and polystyrene. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 6015–6024, 2006