Construction of a portable sample preparation device with a magnetic poly(methacrylic acid‐co‐ethylene dimethacrylate) monolith as the extraction medium and its application in the enrichment of UV filters in water samples

A portable sample preparation device with a magnetic polymer monolith as the extraction medium was constructed. The monolith was synthesized by polymerizing methacrylic acid and ethylene dimethacrylate around a cylindrical magnet. In this way, the monolith with a magnetic core could be readily attached to the extraction device by magnetism. The constructed device was evaluated for the enrichment of UV filters in water samples, followed by high‐performance liquid chromatographic analysis. The extraction efficiency for the targets was satisfactory with no matrix interference. Good linearities were obtained for the UV filters with the correlation coefficients >0.9986. The limits of detection and quantification for the UV filters were 0.3–0.8 and 1.0–2.4 ng/mL, respectively. The recoveries of the UV filters from the spiked water samples at the concentration of 100 ng/mL were 95.3–101.7%, with relative standard deviations <10%. Accordingly, the proposed portable device was demonstrated to be suitable for on‐site simultaneous sampling, purification, and preconcentration within a single step.     

Loading characteristics and chemical stability of headgroup‐functionalized poly(ethylene glycol)‐lipid ligand tethers on polypropylene capillary‐channeled polymer fibers

Polypropylene capillary‐channeled polymer fibers have been modified by adsorption of headgroup‐functionalized poly(ethylene glycol)‐lipids to generate a species‐specific stationary phase. In order to study ligand binding characteristics, a fluorescein‐labeled poly(ethylene glycol)‐lipid was used as a model system. Breakthrough curves and frontal analysis were employed to characterize the surface loading characteristics across a range of lipid concentrations and mobile phase flow rates. Efficient mass transfer and fluid transport yield a linear adsorption isotherm up to the maximum loading concentration of 3 mg/mL, at a linear velocity of 57.1 mm/s. Under these conditions, the dynamic binding capacity was found to be 1.52 mg/g of fiber support. Variation of the linear velocity from 8.6 to 57.1 mm/s showed only small changes in breakthrough volume. The maximum capacity of 1.8 mg/g is found under conditions of a load velocity of 34.2 mm/s and a concentration of 3 mg/mL lipid. Exposure of the lipid modified fibers to several challenge solvents reveals a chemically robust system, with only 50% acetonitrile and hexanes able to disrupt the lipid adsorption. The straightforward capillary‐channeled polymer fiber surface modification with headgroup‐functionalized lipids provides both a diverse yet practically robust ligand tethering system.     

ZnO纳米线基MWNTs/PVDF复合热电材料的制备及特性研究

将不同比例的多壁碳管(MWNTs)与聚偏二氟乙烯(PVDF)聚合物混合后,喷涂于n型ZnO半导体纳米线阵列上,制备了一种新型ZnO纳米线基MWNTs/PVDF热电复合材料.与以往采用价格昂贵的p型与n型单壁碳纳米管(SWNTs)与聚合物混合制备的复合热电材料特性相比,这种新型热电复合材料在降低制造成本的同时,利用分散于聚合物中MWNTs的一维电子传输特性及形成的大量界面势垒,加上ZnO半导体纳米线具有的较高载流子密度与迁移率,提高了复合热电材料中电子的输运特性,增加了材料对声子的散射强度.测试发现,在一定的温度梯度下,随着MWNTs添加质量百分比的增加,热电材料的温差电动势和电导率也随之增加,但其Seebeck系数变化量不大.研究表明,这种热电材料有望替代采用p型与n型SWNTs构建的SWNTs/PVDF复合热电材料.研究结果对开发超轻、无毒、廉价、可应用于各种微纳电子领域的新型电源具有重要的参考价值.     

Theoretical investigation of substitution and end-group effects on poly(p-phenylene vinylene)s

Semi-empirical AM1 and ZINDO/S, as well as density function theory (DFT) method B3LYP/6-31G(d) quantum chemical calculations were carried out to study the electronic structures and optical properties of poly(p-phenylene vinylene) derivatives (PPVs) with 10 and 11 phenylene rings in the backbone. The calculations suggest that the assembly of alternate incorporation of CN and alkoxy substituted phenylene rings in the PPV backbone could be a good way to construct organic semiconductors with low HOMO/LUMO energy band-gaps. The effect of the end-group on the electronic structures and optical properties of the conjugated polymer was investigated by the calculated UV-Vis and UPS spectra. It was demonstrated that the aldehyde and phosphate end-groups have limited effects on the photophysical properties in the UV-visible range.     

Using of the Agglomeration-in-liquid for the Technology of the Fine Materials

The content of the fine and ultrafine particles in the raw material results in difficulty of the separation, the loss of the valuable components and ecological contamination. Secondary using of the fine particles is impossible without their granulation. This problem has been solved by the agglomeration-in-liquid method.An agglomeration-in-liquid method is a process to produce agglomerates in a liquid phase from solid particles suspended in the liquid. The surface of solid particles and the binding liquid must be of identical polarity, but the continuous phase must be of the opposite polarity. The water solutions of the surfactant are the binding liquids or the organic liquids.     

Relation between Morphology and Photoelectrochemical Performance of TiO2 Nanotubes Arrays Grown in Ethylene Glycol/Water

The TiO₂ nanotube films were prepared by anodizing Ti plates in 0.2 M NH₄F ethylene glycol/10% H₂O under different formation voltages keeping fixed the time length, or by keeping fixed the formation voltage and varying the time length. The morphology of the TiO₂ film obtained was observed by SEM images and different morphological parameters were derived from them. Furthermore, the optical and semiconducting properties of TiO₂ films were also measured. The photoelectrochemical performance toward water oxidation of the TiO₂ only showed to be dependent with the inner diameter of the nanotubes, that could be related to the interaction of the film with the light and the transport of species in the electrolyte inward or outward the film.     

Synthesis of dual-doped non-precious metal electrocatalysts and their electrocatalytic activity for oxygen reduction reaction

The pyrolyzed carbon supported ferrum polypyrrole(Fe-N/C) catalysts are synthesized with or without selected dopants, p-toluenesulfonic acid(TsOH), by a facile thermal annealing approach at desired temperature for optimizing their activity for the oxygen reduction reaction(ORR) in O2-saturated 0.1 mol/L KOH solution. The electrochemical techniques such as cyclic voltammetry(CV) and rotating disk electrode(RDE) are employed with the Koutecky-Levich theory to quantitatively obtain the ORR kinetic constants and the reaction mechanisms. It is found that catalysts doped with TsOH show significantly improved ORR activity relative to the TsOH-free one. The average electron transfer numbers for the catalyzed ORR are determined to be 3.899 and 3.098, respectively, for the catalysts with and without TsOH-doping. The heat-treatment is found to be a necessary step for catalyst activity improvement, and the catalyst pyrolyzed at 600℃ gives the best ORR activity. An onset potential and the potential at the current density of-1.5 mA/cm2 for TsOH-doped catalyst after pyrolysis are 30 mV and 170 mV, which are more positive than those without pyrolized. Furthermore, the catalyst doped with TsOH shows higher tolerance to methanol compared with commercial Pt/C catalyst in 0.1 mol/L KOH. To understand this TsOH doping and pyrolyzed effect, X-ray diffraction(XRD), scanning electron microscope(SEM) and X-ray photoelectron spectroscopy(XPS) are used to characterize these catalysts in terms of their structure and composition. XPS results indicate that the pyrrolic-N groups are the most active sites, a finding that is supported by the correspondence between changes in pyridinic-N content and ORR activity that occur with changing temperature. Sulfur species are also structurally bound to carbon in the forms of C–Sn–C, an additional beneficial factor for the ORR.     

A new two‐dimensional manganese(II) coordination polymer based on thiophene‐3,4‐dicarboxylic acid

A novel manganese coordination polymer, poly[(μ₅‐thiophene‐3,4‐dicarboxylato)manganese(II)], [Mn(C₆H₂O₄S)]_n, was synthesized hydrothermally using 3,4‐thiophenedicarboxylate (3,4‐tdc²⁻) as the organic linker. The asymmetric unit of the complex contains an Mn²⁺ cation and one half of a deprotonated 3,4‐tdc²⁻ anion, both residing on a twofold axis. Each Mn²⁺ centre is six‐coordinated by O atoms of bridging/chelating carboxylate groups from five 3,4‐tdc²⁻ anions, forming a slightly distorted octahedron. The Mn²⁺ centres are bridged by 3,4‐tdc²⁻ anions to give an infinite two‐dimensional layer which incorporates one‐dimensional Mn–O gridlike chains, and in which the 3,4‐tdc²⁻ anion adopts a novel hexadentate chelating and μ₅‐bridging coordination mode. The fully deprotonated 3,4‐tdc²⁻ anion exhibits unexpected efficiency as a ligand towards the Mn²⁺ centres, which it coordinates through all of its carboxylate O atoms to provide the novel coordination mode. The IR spectrum of the complex is also reported.     

Coordination polymer chains built from CuII and adipate ions linked by hydrogen bonds to form a three‐dimensional framework structure

In the title compound, catena‐poly[bis[(2,2′‐bipyridine‐κ²N,N′)(1,1,3,3‐tetracyano‐2‐ethoxypropenido‐κN)copper(II)]‐μ₄‐hexanedioato‐κ⁶O¹,O^1′:O¹:O⁶,O^6′:O⁶], [Cu₂(C₉H₅N₄O)₂(C₆H₈O₄)(C₁₀H₈N₂)₂]_n, the adipate (hexanedioate) dianion lies across a centre of inversion in the space group P. The Cu^II centre adopts a distorted form of axially elongated (4+2) coordination, and the Cu^II and adipate components form a one‐dimensional coordination polymer from which the 2,2′‐bipyridine and 1,1,3,3‐tetracyano‐2‐ethoxypropenide components are pendent, and where each adipate dianion is bonded to four different Cu^II centres. The coordination polymer chains are linked into a three‐dimensional framework structure by a combination of C—H...N and C—H...O hydrogen bonds, augmented by a π–π stacking interaction.     

Comparison of Loading Efficiency between Hyperbranched Polymers and Cross‐Linked Nanogels at Various Branching Densities

The effect of branching point structures and densities is studied between azido‐containing hyperbranched polymers and cross‐linked nanogels on their loading efficiency of alkynyl‐containing dendron molecules. Hyperbranched polymers that contained “T”‐shaped branching linkage from which three chains radiated out and cross‐linked nanogels that contained “X”‐shaped branching linkage with four radiating chains are synthesized in microemulsion using either atom transfer radical polymerization (ATRP) or conventional radical polymerization (RP) technique. Both polymers have similar density of azido groups in the structure and exhibit similar hydrodynamic diameter in latexes before purification. Subsequent copper‐catalyzed azide–alkyne cycloaddition reactions between these polymers and alkynyl‐containing dendrons in various sizes (G1–G3) demonstrate an order of dendron loading efficiencies (i.e., final conversion of alkynyl‐containing dendron) as hyperbranched polymers > nanogels synthesized by ATRP > nanogels synthesized by RP. Decreasing the branching density or using smaller dendron molecules increases the click efficiency of both polymers. When G2 dendrons with a molecular weight of 627 Da are used to click with the hyperbranched polymers composed of 100% inimer, a maximum loading efficiency of G2 in the loaded hyperbranched polymer is 58% of G2 by weight. These results represent the first comparison between hyperbranched polymers and cross‐linked nanogels to explore the effect of branching structures on their loading efficiencies.