Toughness mechanism in polypropylene composites: Polypropylene toughened with elastomer and calcium carbonate

Polypropylene (PP) was modified with elastomer or CaCO₃ particles of two different sizes (1 μm and 50 nm) in various volume fractions. The dispersion morphology and mechanical properties of the two systems were investigated as functions of the particle size and volume fraction of the modifier. The brittle‐to‐tough transition occurred when the matrix ligament thickness was less than the critical ligament thickness, which was about 0.1 μm for the PP used here, being independent of the type of modifier. At the same matrix ligament thickness, the improvement of the toughness was obviously higher with the elastomer rather than with CaCO₃, but adding CaCO₃ increased the modulus of PP. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 1656–1662, 2004     

Ultrahigh‐molecular‐weight‐polyethylene‐fiber surface treatment by electron‐beam‐irradiation‐induced graft polymerization and its effect on adhesion in a styrene–butadiene rubber matrix

Aiming to develop a high‐performance fiber‐reinforced rubber from styrene–butadiene rubber (SBR), we applied a special technique using electron‐beam (EB)‐irradiation‐induced graft polymerization to ultrahigh‐molecular‐weight‐polyethylene (UHMWPE) fibers. The molecular interaction between the grafted UHMWPE fibers and an SBR matrix was studied through the evaluation of the adhesive behavior of the fibers in the SBR matrix. Although UHMWPE was chemically inert, two monomers, styrene and N‐vinyl formamide (NVF), were examined for graft polymerization onto the UHMWPE fiber surface. Styrene was not effective, but NVF was graft‐polymerized onto the UHMWPE fibers with this special method. A methanol/water mixture and dioxane were used as solvents for NVF, and the effects of the solvents on the grafting percentage of NVF were also examined. The methanol/water mixture was more effective. A grafting percentage of 16.4% was the highest obtained. This improved the adhesive force threefold with respect to that of untreated UHMWPE fibers. These results demonstrated that EB irradiation enabled graft polymerization to occur even on the inert surface of UHMWPE fibers. However, the mechanical properties of the fibers could be compromised according to the dose of EB irradiation. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 2595–2603, 2004     

Effects of poly[styrene‐b‐(ethylene‐co‐butylene)‐b‐styrene] on the charge distributions of low‐density polyethylene/polystyrene blends

The effect of the triblock copolymer poly[styrene‐b‐(ethylene‐co‐butylene)‐b‐styrene] (SEBS) on the formation of the space charge of immiscible low‐density polyethylene (LDPE)/polystyrene (PS) blends was investigated. Blends of 70/30 (wt %) LDPE/PS were prepared through melt blending in an internal mixer at a blend temperature of 220 °C. The amount of charge that accumulated in the 70% LDPE/30% PS blends decreased when the SEBS content increased up to 10 wt %. For compatibilized and uncompatibilized blends, no significant change in the degree of crystallinity of LDPE in the blends was observed, and so the effect of crystallization on the space charge distribution could be excluded. Morphological observations showed that the addition of SEBS resulted in a domain size reduction of the dispersed PS phase and better interfacial adhesion between the LDPE and PS phases. The location of SEBS at a domain interface enabled charges to migrate from one phase to the other via the domain interface and, therefore, resulted in a significant decrease in the amount of space charge for the LDPE/PS blends with SEBS. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 2813–2820, 2004     

Statistical thermodynamics evaluation of polymer–polymer miscibility

The Simha and Somcynsky (S–S) statistical thermodynamics theory was used to compute the solubility parameters as a function of temperature and pressure [δ = δ(T, P)], for a series of polymer melts. The characteristic scaling parameters required for this task, P*, T*, and V*, were extracted from the pressure–temperature–volume (PVT) data. To determine the potential polymer–polymer miscibility, the dependence of δ versus T (at ambient pressure) was computed for 17 polymers. Close proximity of the δ versus T curves for four miscible polymer pairs: PPE/PS, PS/PVME, and PC/PMMA signaled the usefulness of this approach. It is noteworthy, that the tabulated solubility parameters (derived from the solution data under ambient conditions) propounded the immiscibility of the PVC/PVAc pair. The computed values of δ also suggested miscibility for polymer pairs of unknown miscibility, namely PPE/PVC, PPE/PVAc, and PET/PSF. In recognizing the limitations of the solubility parameter approach (the omission of several thermodynamic contributions), these preliminary results are auspicious because they indicate a new route for estimating the miscibility of any polymeric material at a given temperature and pressure. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 2909–2915, 2004     

Structure,morphology, and crystallization process of isotactic polypropylene/hydrogenated hydrocarbon resin blends

The structure, morphology, and isothermal and nonisothermal crystallization of isotactic polypropylene/low‐molecular‐mass hydrocarbon resin blends (iPP/HR) (up to 20% in weight of HR) have been studied, using optical and electron microscopy, wide‐ and small‐angle X‐ray and differential scanning calorimetry. New structures and morphologies can be activated, using appropriate preparation and crystallization conditions and blend composition. For every composition and crystallization condition, iPP crystallizes in α‐form, with a spherulitic morphology. The size of iPP spherulites increases with resin content, whereas the long period decreases. In the range of crystallization temperatures investigated, HR modifies the birefringence of iPP spherulites, favoring the formation of radial lamellae and changing the ratio between tangential and radial lamellae. Spherulitic radial growth rates, overall crystallization rates, and melting temperatures are strongly affected by resin, monotonically decreasing with resin content. This confirms miscibility in the melt between the two components of the blends. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 3368–3379, 2004     

Preparation and characterization of finely dispersed drugs. 5. Ethyl 3,5-di(acetylamino)-2,4,6-triiodobenzoate

Controlled precipitation of the diagnostic imaging agent ethyl 3,5-di(acetylamino)-2,4,6-triiodobenzoate has been used to produce fine particles of various sizes, morphologies, and degrees of crystallinity, which depended on experimental conditions. In addition, two distinct polymorphic forms of the drug have been fully characterized by single crystal X-ray diffraction studies, and evidence for a third polymorph was also observed. Some of the so prepared dry particles were coated with a thin layer of silica.     

X波段六腔渡越管振荡器的高频特性研究

 从麦克斯韦方程出发，采用时域有限差分法（FDTD）和离散傅里叶变换（DFFT）相结合的方法，通过数值计算得出了六腔开放式谐振腔中前四个谐振频率和场分布，计算出的谐振频率与实验测量结果基本相同。比较了开放腔和封闭腔谐振频率，验证了TEM波吸收边界条件，并在实际编程计算中得以应用。计算结果为六腔渡越管振荡器的机理研究提供了依据。     

EQCM Study of the Couple Thallium(I)/Thallium Amalgam at a Thin Film Mercury Electrode

EQCM and voltammetric data show that thallium(I) ions, which are adsorbed in the region of the positive surface charge, most probably, in the form of the ionic pairs, are not reduced. In this potential region, thallium(I) ions are reduced directly from the solution. At more negative potentials, the previously adsorbed stable ionic pairs slowly undergo transition into the less stable form. From this form, thallium(I) ions can be reduced or desorbed into the solution. The process is best described by a model of one electron, i.e., full charge transfer.     

Preparation of Functional Fluorescent Microspheres Used for HTS and Their Interaction with Biomolecules

There is considerable interest in protein adsorption onto microspheres because of its importance in a wide range of biomedical applications, such as artificial tissues and organs, drug delivery systems, biosensors, solid-phase immunoassays, immunomagnetic cell separation and immobilized enzymes or catalyst. It has been well known that the interaction between proteins and microspheres plays important roles in this process. Major interaction involved in the adsorption can be classified as electrostatic, hydrophobic and hydrogen-bonding. Indeed, adsorption of proteins onto microspheres is a complex process and often can involve many dynamic steps, from the initial attachment of the protein on the surface of microspheres to the equilibrium. Also the conformation of proteins probably occurs to a certain degree of deformation or structural change due to the large area of contact. Recently, much interest has been shown in sulfonated microspheres, since sulfonate-group itself is one of components in bio-bodies, as well as is sensitive to the change of pH or ionic strength. Indeed, so far, scanty investigations have been performed in the full range. Also few researches have involved the data on adsorption rate and the maximum amount of protein adsorbed, or the reversibility of the process and conformational change of protein adsorbed as well.In present study, BSA (bovine serum albumin) was chosen as the model protein and sulfonated PMMA [poly(methyl methacrylate)] microspheres as the matrix to investigate the adsorption process.The purpose is to show some information especially the intrinsic information involved by the adsorption process Adsorption of BSA onto sulfonated microspheres (MS) has been investigated as a function of time, protein concentration and pH. The adsorption appears to be a reversible process and the presence of sulfonate groups can play important roles in the adsorption process, so as to increase the amount of protein adsorbed and influences the interaction of BSA molecules. Fig. 1 also shows that the reciprocation between unadsorbed and adsorbed BSA or rearrangement of adsorbed BSA molecules does not produce visible change in the properties of the adsorbed protein. Close to the isoelectric point of BSA (pI 4.7), the amount of protein adsorbed exhibits a maximum. A higher or lower pH results in the significant decrease of the adsorption amount. This is related to the dependence of BSA conformations at different pH conditions.     

A Novel Model for Protein Immobilization on Microspheres

The immobilization of proteins, especially receptor proteins commonly used in high through-put screening of drugs (HTS), have received great attention in recent years. There are many successful isothermal models for describing the adsorption of protein onto solid surface, such as Langmuir model, Bi-Langmuir model, Fowler model, Freundlich model, Freundlich-Langmuir model and Tekmin model etc. In all these models, Langmuir model was the most favorable one model accepted by many researchers, but the experimental results showed that it was not entirely fit to all adsorption behaviors. So new models were required for describing protein adsorption onto microspheres in different conditions.In our research, a novel isothermal model, including Langmuir and other adsorbing behaviors was presented basing on the holding degree of surface active sites and the interaction styles of protein immobilization. In Langmuir model, the adsorbing amount of protein was described as [PS] =Km[P]/1 + K[P], where [PS] was the concentration of adsorbed protein, [P] was the concentration of freeprotein at equilibrium state, and Km and K was constant. According to the interactions of protein and ligands, there were three patterns in the interactions of protein and ligands. On the similar assumption that the interaction of protein and microspheres were three styles, and based on the definition of the holding degree of surface active sites (Y), three adsorption behaviors could be described as Y K[ P ]φ/ K[P]φ+1 or ln K + φ ln[P] =ln(Y/1-Y) in which [P] was the concentration of free protein at equilibrium state, and φ and K was constant. Different scale of φ presented different adsorption behaviors, especially when φ was 1, the adsorption behavior was Langmuir adsorbing model. Figure I indicated the different adsorbing results in different adsorption behaviors (φ＞1, φ＜1,and φ=1).