Influence of MgO on structure and optical properties of alumino-lithium-phosphate glasses

MgO doped lithium alumino phosphate glasses (PLA: P₂O₅+Li₂O+Al₂O₃+MgO) were prepared by melt quenching technique. Raman spectra display three significant peaks at 698, 1164 and 1383 cm⁻¹ attributed to: symmetric stretching vibrations of the bridging oxygen (BO) in the P–O–P chains, symmetric stretching vibrations of the PO₂ groups, and the asymmetric vibrations vas(PO₂) of the non-bridging oxygen (NBO) atoms, respectively. Also, the density, molar volumes and ion concentration have been discussed and correlated with the structural changes within the glassy matrix. Some optical constants such as refractive index and dispersion parameters (E_o: single-oscillator energy and E_d: dispersive energy) of the glasses were determined. Finally, the values of the optical band gap for direct and indirect allowed transitions have been determined from the absorption edge studies. It is deduced that the values of E_opt increase with increasing MgO content. It was assigned to structural changes induced from the formation of non-bridging oxygen. The Urbach energy (ΔE) was found to decrease from 0.578 to 0.339 eV with increasing MgO content from 0.5 to 2 mol.     

固相烧结法制备锂离子电池正极材料Li2FeP2O7及其电化学性能研究

介绍了一种先冷冻干燥后固相烧结制备正极材料Li₂FeP₂O₇的方法. 利用X射线衍射(XRD)、 扫描电子显微镜(SEM)、 透射电子显微镜(TEM)和傅里叶变换红外光谱(FTIR)对材料的组成和形态进行表征, 并通过循环伏安曲线(CV)和电化学阻抗谱(EIS)研究了Li₂FeP₂O₇材料的电化学性能. 研究发现, 合成Li₂FeP₂O₇的最佳温度为590 ℃, 此温度下反应较完全且产物杂质较少, 1.6C倍率下的放电比容量达到55 mA·h·g^?1, 明显高于其它温度下合成样品的放电比容量. 该温度下合成的Li₂FeP₂O₇还具有低阻抗和较大的交换电流密度, 说明这种合成方式有利于提高锂离子在Li₂FeP₂O₇中的扩散.     

基于表界面反应及优化的锂金属电池研究进展

金属锂具有高理论比容量和低还原电位, 是锂电池阳极的理想材料之一. 但在长期循环充放电过程中, 金属锂因锂枝晶生长会导致出现界面恶化及能量损失严重等问题, 对锂金属电极与电解质表界面反应的优化是一个重要研究方向. 本文介绍了锂枝晶产生的危害, 从分析及抑制锂枝晶沉积两方面综合评述了为解决这一问题所采取的方法, 包括固态电解质界面形成机制和保护机理、 表面改性、 三维锂阳极和液态/固态电解质等方法, 总结了各种方法的优劣势, 并展望锂金属电池在能源领域的研究前景.     

金属锂负极的成核机制与载体修饰

金属锂具有电位低、比容量高等突出优点,是极具吸引力的下一代高能量密度电池的负极材料,然而存在枝晶、死锂、副反应严重、库伦效率低、循环稳定性差等问题,限制了其实际应用。金属锂负极的成核是电化学沉积过程中的重要步骤,锂在集流体或导电载体上的均匀成核和稳定生长对于抑制枝晶死锂、提高充放电效率和循环性能具有关键作用。本文从成核机制与载体效应的角度概述了锂金属负极的研究进展,介绍了锂成核驱动力、异相成核模型、空间电荷模型等内容,分析了锂核尺寸及分布与过电位和电流密度的关系,并通过三维载体分散电流密度、异相晶核/电场诱导成核、晶格匹配等方面的研究实例讨论了载体修饰对锂负极的性能提升。     

锂金属负极人造保护膜的研究进展

金属锂因其具有极高的理论容量(3860 mAh·g^?1)、最低的电极电位(?3.04 V vs.标准氢电极)和低的密度(0.534 g·cm^?3),被认为是最具潜力的负极材料。但循环过程中不可控的枝晶生长及不稳定的固体电解质相界面膜所引起的安全隐患和电池库伦效率低等问题严重阻碍了锂金属负极的发展。通过在电极表面构建人造保护膜可以有效调控锂离子沉积行为,因此人造保护膜的构建是一种简单高效抑制锂枝晶生长的策略。本综述将从聚合物保护膜、无机保护膜、有机-无机复合保护膜和合金保护膜总结了人造保护膜的构建方法、抑制锂枝晶生长机理,为促进高比能锂金属电池的商业化应用提供借鉴参考作用。     

Sulfone-based high-voltage electrolytes for high energy density rechargeable lithium batteries:Progress and perspective

Further enhancement in the energy density of rechargeable lithium batteries calls for high-voltage cathode materials and stable anodes,as well as matched high-voltage electrolytes without compromising the overall property of batteries.Sulfone-based electrolytes have aroused great interest in recent years owing to their wide electrochemical window and high safety.However,significant challenges such as the complexity of synthesis,high melting point(typically above room temperature),high viscosity,and their poor compatibility with graphite-based anodes have drastically impeded their practical applications.In this review,recent progress of sulfone solvents in high energy density rechargeable lithium batteries is summarized theoretically and experimentally.More importantly,general improvement methods of sulfone-based electrolytes,such as adding additives and cosolvents,structural modifications of sulfo ne,superconcentrated salt strategy are briefly discussed.We expect that this review provides inspiration for the future developments of sulfone-based high-voltage electrolytes(SHVEs) and their widespread applications in high specific energy lithium batteries.     

Improved performance of porous LiFePO4/C as lithium battery cathode processed by high energy milling comparison with conventional ball milling

Porous LiFePO₄ is synthesized and coated with amorphous carbon by using high energy nano-mill (HENM) processed solid-state reaction method. FeCl₃ (38%) containing water solution which is originated from pickling of steel scrap (waste liquid) is used as a source material in this study. The result indicates that LiFePO₄ powders are well coated with the amorphous carbon. HENM process successfully produces the porous LiFePO₄ with homogeneously distributed pores and a well networked carbon web, which delivers an enhanced electrochemical rate capability. HENM process is incorporated as an effective route for reducing particle size, distributing particle homogeneously and averting agglomeration of particles of precursor in this study. X-ray diffraction, scanning electron microscopy with elemental mapping, transmission electron microscopy with selected area (electron) diffraction, Raman spectroscopy, cyclic voltammetry, and galvanostatic charge/discharge are employed to characterize the final product. Electrochemical measurement shows that the synthesized LiFePO₄/C composite cathode delivers an initial discharge capacity of 161 mAhg⁻¹ at 0.1C-rate between 4.2 and 2.5 V. Remarkably, the cathode delivers 101.9 mAhg⁻¹ at high charge/discharge rate (10 C).     

Prototype electrochromic device and dye sensitized solar cell using spray deposited undoped and ‘Li’ doped V2O5 thin film electrodes

Lithium (Li) (0–5 wt%) doped V₂O₅ thin films were spray deposited at 450 °C onto ITO substrates. Structural analysis using X-ray diffraction and Raman spectroscopy revealed orthorhombic phase of the films. In addition to the V₂O₅ phase, presence of VO₂ peaks due to high deposition temperature is also evident from structural and optical characterization. The non-stoichiometric nature of the films due to loss of the terminal O atom was confirmed from Raman spectroscopy. The direct band gap, indirect bandgap, and phonon energies were also calculated from optical studies. Different charge states of vanadium ions present in the film were identified from X-ray photoelectron spectroscopy study. Results from cyclic voltammetry experiments reflected significant differences between the undoped and Li doped V₂O₅ samples. Transport properties by Hall-effect measured at room temperature indicated significant increase in conductivity, carrier concentration and mobility of V₂O₅ thin films on doping with Li. A Dye Sensitized Solar Cell (DSSC) was fabricated using mobility enhanced 5 wt% Li doped V₂O₅ film as photoanode and its efficiency was found to be 2.7%. A simple electrochromic cell is fabricated using undoped V₂O₅ thin film to demonstrate the colour change.     

Synthesis and electrochemical characteristics of xLi2MnO3–(1−x)Li(Mn0.375Ni0.375Co0.25)O2 (0.0 ≤ x ≤ 1.0) thin film cathode for lithium rechargeable micro batteries

We have compared the structure, microstructure, and electrochemical characteristics of xLi₂MnO₃–(1−x)Li(Mn_0.375Ni_0.375Co_0.25)O₂ (0.0 ≤ x ≤ 1.0) thin films with their bulk cathode laminate counterparts of identical compositions. Pure Li(Mn_0.375Ni_0.375Co_0.25)O₂ as well as the synthesized composite films partially transform into cubic spinel structure during charge–discharge cycling. In contrast, such layered to spinel phase transformation has only been identified in bulk cathode laminates with x ≥ 0.75. At a current density 0.05 mAcm⁻², the discharge capacity of Li(Mn_0.375Ni_0.375Co_0.25)O₂ thin film was measured to be ∼60 μAhcm⁻². The discharge capacity (∼217 μAhcm⁻²) was markedly improved in x∼0.5 composite thin film. The capacity retention after 20 charge discharge cycles are improved in composite films; however, their capacity fading could not be eliminated completely.