Methanol electrooxidation on platinum mesh electrodes bonded to solid polymer electrolytes

Methanol electrooxidation on smooth platinum electrodes bonded to solid polymer electrolytes was studied in water and acid solution by voltammetric measurements with different scanning rates. An enhancement of the oxidation rates was observed in these systems as compared to identical platinum electrodes in contact with liquid electrolytes. This electrocatalytic effect strongly depends on the measuring conditions and on the electrode potential. The reasons for the catalytic effects at different potentials are discussed. Received: 8 January 1997 / Accepted: 1 December 1997     

Fabrication of solid thin film electrolyte and LiCoO2 by aerosol flame pyrolysis deposition

Aerosol flame pyrolysis deposition method was applied to deposit the oxide glass electrolyte film and LiCoO₂ cathode for thin film type Li-ion secondary battery. The thicknesses of as-deposited porous LiCoO₂ and Li₂O–B₂O₃–P₂O₅ electrolyte film were about 6 μm and 15 μm, respectively. The deposited LiCoO₂ was sintered for 2 min at 700 °C to make partially densified cathode layer, and the deposited Li₂O–P₂O₅–B₂O₃ glass film completely densified by the sintering at 700 °C for 1 h. After solid state sintering process the thicknesses were reduced to approximately 4 μm and 6 μm, respectively. The cathode and electrolyte layers were deposited by continuous deposition process and integrated into a layer by co-sintering. It was demonstrated that Aerosol flame deposition is one of the good candidates for the fabrication of thin film battery.     

Formal Mathematical Analysis of the Existence of the Common Intersection Point in Relation to Determining the Parameters Describing Ion Adsorption at the Oxide/Electrolyte Interface: Comparison of the Triple and Four-Layer Models

For most oxide/electrolyte systems potentiometric titration curves measured for different ionic strengths have a Common Intersection Point (CIP) which corresponds to the Point of Zero Charge (PZC). However, there are systems where a CIP exists but the surface charge at this point does not equal zero (PZC CIP). In this paper theoretical analysis of the systems in which the PZC and CIP do not coincide is presented. It is based on the well-known 2-pK surface charging approach and Triple Layer Model (TLM) as well as the Four Layer Model (FLM) of the electric double layer. The appropriate mathematical criterion for CIP existence was applied with detailed derivations, both for TLM and FLM. Having determined in this manner the parameter values, one can draw proper conclusions about the features of oxide/electrolyte adsorption systems, in which PZC and CIP do not coincide. The values of adsorption parameters are found by fitting simultaneously the obtained theoretical expressions to both of the experimental titration isotherms, and to the individual isotherms of electrolyte cation adsorption measured using radiometric methods.     

Surface structure and electrochemical characteristics of natural graphite fluorinated by ClF3

Natural graphite samples with average particle sizes of 5, 10 and 15 μm (NG5 μm, NG10 μm and NG15 μm, respectively) were fluorinated by ClF₃ (3 × 10⁴ Pa) at 200 and 300 °C for 2 min. X-ray photoelectron spectra of surface-fluorinated samples showed that surface fluorine concentration increased with increase in the particle size of graphite and reaction temperature. Small amounts of chlorine were also detected in all the fluorinated samples. Raman spectra of original and surface-fluorinated samples indicated that the surface disordering was increased for NG10 μm and NG15 μm. Surface areas were decreased by the fluorination for NG5 μm and NG10 μm but unchanged for NG15 μm. The mesopores with diameter of 1.5-2 nm increased while those of 2-3 nm decreased for all the samples. First coulombic efficiencies for NG10 μm and NG15 μm were highly increased by surface fluorination in 1 mol/dm³ LiClO₄-EC/DEC/PC (EC: ethylene carbonate, DEC: diethyl carbonate, PC: propylene carbonate) solution.     

Hydrolysis in the system LiPF6—propylene carbonate—dimethyl carbonate—H2O

¹⁹F and ³¹P NMR spectroscopy were used to study the kinetics of the hydrolysis of LiPF₆ in the homogenous solvent system propylene carbonate (PC)—dimethyl carbonate (DMC)—H₂O. It was found that the main products of the hydrolysis are HF, LiPO₂F₂ and Li₂PO₃F. The content of POF₃ and PF₅ was negligibly low. We set up a hypothesis that the main factor determining the rate of the process is the so-called ‘secondary’ catalytic effect, caused by solvated H⁺ ions.     

Convenient procedure of Horner-Wadsworth-Emmons olefination for the synthesis of simple and functionalized α,β-unsaturated nitriles

A mild and practical procedure of Horner-Wadsworth-Emmons olefination promoted by lithium hydroxide and α-cyano phosphonates has been set up for the synthesis of α,β-unsaturated nitriles. The reaction conditions are tolerated by functionalized ketones and the exclusive formation of E-γ-hydroxy α,β-unsaturated nitriles has been observed.     

Ce0.8Y0.2O1.9-Ca3(PO4)2-K3PO4复合电解质在中温区的质子导电性及在常压合成氨中的应用

A precursor of Ce_0.8Y_0.2O_1.9(YDC) solid electrolyte was synthesized by the gol-gel method. YDC and phosphates powders were prepared by mixing the YDC and phosphates according to different weight ratios. The mixtures of the YDC and binary phosphates were ground and sintered at 1 400 ℃. The proton conductivity in solid electrolyte of the sintered samples was examined using electrochemical methods at 400～800 ℃. Ammonia was synthesized from nitrogen and hydrogen at atmospheric pressure in the solid state proton conducting cell reactor. The optimal condition for the ammonia production was determined. The result indicated that composite electrolyte of 80wt% YDC: 20wt% binary phosphates as proton conductor could obtain the highest ionic conductivity and ammonia production rate among the four samples, the rate of evolution of ammonia was up to 9.5 × 10^-9 mol·s^-1·cm^-2.     

磺酸型聚氨酯离聚物的离子导电性能

本文以多种聚醚为软段，二异氰酸酯（ＭＤＩ和ＴＤＩ）为硬段，合成了多嵌段聚醚聚氨酯，以此聚氨酯为基材，与ＮａＨ及１，３－丙碳酸内酯反应，进一步合成了一系列不同离子化程度的阴离子型碳化聚氨酯离聚物，用交流阻抗谱仪测定了样品的阻抗谱，由此计算出样品的离子电导率。研究结果表明其他条件相同时，以聚乙二醇（ＰＥＧ）为软段的样品具有较高的离子电导率；以聚环氧丙烷（ＰＰＯ）为软段的样品次之，以聚四氢呋喃（ＰＴＭＯ）为软段的样品最低，对于离子化程度不同的聚氨酯离聚物以金属离子和烷氧单元之比为０．０５时导电性能最好。阳离子为Ｌｉ＋和Ｎａ＋的样品具有相近的离子电导率。     

TiO2/P(VdF-HFP)杂化纤维微孔膜的制备及其电化学性能

用电纺法制备了TiO₂/P(VdF-HFP)(聚偏氟乙烯-六氟丙烯共聚物)杂化纤维微孔膜, 用SEM观察了杂化纤维微孔膜的形貌, 并测算了这类由超细纤维相互搭接而形成的微孔膜的孔隙率. 这种微孔膜吸附LiPF₆/EC-DMC-EMC(碳酸乙烯酯-二甲基碳酸酯-碳酸甲乙酯)电解质溶液后得到凝胶聚合物电解质膜. 用电化学方法测试了聚合物电解质膜的离子电导率、锂离子迁移数等参数, 并研究了TiO₂纳米晶的掺入对聚合物电解质电化学性能的影响. 结果表明, TiO₂的掺入降低了P(VdF-HFP)聚合物基体的结晶度, 改善了凝胶聚合物电解质的低温电化学性能.