Adsorption of anti-human IgG to plasma-polymerized allylamine film formed on a silver plate

Increase in the sensitivity of an immunosensor or biosensor requires the immobilization of a large amount of proteins. Good materials must be developed for this protein adsorption. Allylamine thin film was formed on a flat silver plate by plasma polymerization; this plate is referred to as Ag(ALAM). Ag(ALAM) films were characterized by SEM, FT–IR and ESCA. Investigations on adsorption and desorption of F(ab')₂ anti-human IgG (hIgG) on to Ag and Ag(ALAM) revealed the following: (1) The adsorption isotherm of F(ab')₂ anti-hIgG on to AG(ALAM) or Ag was of a Langmuir type. The binding constant (K_b) and saturation binding (A_b) for this protein on to Ag(ALAM) were 8.93 l/mol and 181.8 nmol/m², respectively, and for Ag, were 7.71 l/mole and 87.9 nmol/m². (2) The extent of desorption of labeled F(ab')₂ anti-hIgG absorbed on the two plates was the same. (3) Ag(ALAM) and Ag were used as solid phases in a two-site immunoradiometric assay of human serum IgG. The dose-response on AG(ALAM) occurred at lower concentration, and was of greater magnitude than that on Ag.     

Sorption–desorption studies of six pyrethroids and mirex on soils using GC/MS-NICI

Sorption–desorption equilibria of six pyrethroids (permethrin, cyfluthrin, cypermethrin, λ-cyhalothrin, deltamethrin and fenvalerate) and mirex were determined in soils possessing a range of organic content (1.15–2.46%). Solutions (in deionized water, pH 6.5–7.4) of the samples were shaken using a mechanical shaker for 24?h. The suspensions were centrifuged and aliquots of clear supernatant were passed through a C-18 column (SPE extraction). The eluates were concentrated to dryness before a volumetric standard was added. The analytes were determined by gas chromatography with negative ion chemical ionization mass spectrometry (GC/MS-NICI) either in SIR or SCN mode. Sorption isotherm parameters (n and k) were calculated according to the Freundlich equation. The values of n are around unity. Permethrin and cyfluthrin were the least sorbed pyrethroids, k<2, mirex and fenvalerate the most. The effect of the pH on sorption was examined also (at pH values 2, 4, 6 and 9). Sorption behaviour on different soils and silica was also examined. Desorption studies were conducted on the same pyrethroid solutions. After sorption, the supernatant was replaced with a similar volume of deionized water. Desorption was achieved by removing all the supernatant from the centrifuged samples and then replacing it with deionized water. This equilibration process was repeated five times. Each time the suspension was centrifuged, concentrated and analyzed using GC/MS analysis. The residual amount of pyrethroid on the soil was calculated as the difference between the initial amount and the desorbed amount (mass balance).     

Review of corrosive environments for copper and its corrosion inhibitors

This review paper deals with corrosion of copper and its alloys in corrosive environments and their corrosion inhibitors. The main corrosion inhibitor groups for copper are introduced and a review of adsorption models is provided. The main part of this work is to investigate different corrosive environments for copper and its alloys and their corrosion inhibitors used in such environments to protect copper. According to the literature, the corrosion inhibition behavior of organic corrosion inhibitors and their derivatives in comparison with inorganic ones are further evaluated. Knowing maximum corrosion inhibition efficiency of a specific corrosion inhibitor in a specific corrosive environment is helpful to choose the most appropriate corrosion inhibitor compound.     

Which molecularly imprinted polymer is better?

Molecularly imprinted polymers (MIP) have been successfully synthesized toward many different compounds in the last decades. The mechanistic details of selective binding at binding sites are not yet well understood. For this reason the characterization of MIP binding has been mostly phenomenological and this makes the transfer of results between different laboratories or between different types of applications difficult. In this paper we analyze the relationship between different types of characterization like isotherms, binding site models, chromatographic k and α values, etc. as they relate to different applications like HPLC, solid phase extraction (SPE), binding assays, batch extraction and sensors. It is shown that α values determined by elution chromatography depend on seemingly irrelevant factors as the length and diameter of the column, respectively. The determination of distribution ratios or partition coefficients is proposed as an easily understandable and useful quantity in the characterization of novel MIPs. Data used for the characterization of a MIP should be transferable between different applications but the qualification of MIPs as better or worse will depend on the application in case.     

Removal of chromate from water by a new CTAB-silica gelatin composite

A novel composite able to remove hexavalent chromium Cr(VI) from aqueous solutions was obtained by adding the silica precursor tetraethoxysilane (TEOS) to the hexadecyltrimethylammonium bromide (CTAB) microemulsion-based gel. A physical characterization of the new matrix revealed high stability of the silica gelatin composite in water at high temperatures and at neutral pH. Good efficiency in removing chromate from neutral solutions was also demonstrated by the adsorption kinetics. In particular, the adsorption data of chromate obtained with the CTAB-silica gelatin composite at 25 degrees C and pH 7.5 are described by the Freundlich isotherm model. The specific role of CTAB in the silica gelatin composite was also evaluated by comparing the kinetics of the anionic AOT-silica gelatin composite to the CTAB one. The data collected clearly showed that the positively charged surfactant was necessary to efficiently adsorb Cr(VI) from aqueous solutions. SEM and pulsed gradient spin-echo NMR analysis of the composite demonstrated that the silicon is well assembled in the gelatin network, in which water molecules maintain a high mobility. The diffusion coefficient of water in this system was shown to remain close to the value of pure water. Finally, X-ray analyses of the elemental content in the CTAB-silica gelatin composite indicated no difference in terms of percentage of silica distributions in different areas of the matrix and suggested that chromium adsorption could take place in internal areas.     

Dynamic Behaviors and Morphology Change of Anionic Phospholipid DPPG Monolayer Caused by Bovine Serum Albumin at Air-Water Interface

The interaction between bovine serum albumin (BSA) and the anionic 1.2-dipalmitoyl-snglycero- 3-(phospho-rac-(1-glycerol)) (sodium salt) (DPPG) phospholipid at different subphase pH values was investigated at air-water interface through surface pressure measurements and atomic force microscopy (AFM) observation. By analyzing surface pressure-mean molecular area (π-A) isotherms, the limiting molecular area in the closed packing state-the concentration of BSA (A_lim-[BSA]) curves, the compressibility coefficient-surface pressure (C_S^-1-π) curves and the difference value of mean molecular area-the concentration of BSA (ΔA-[BSA]) curves, we obtained that the mean molecular area of DPPG monolayer became much larger when the concentration of BSA in the subphase increased at pH=3 and 5. But the isotherms had no significant change at different amount of BSA at pH=10. In addition, the amount of BSA molecules adsorbed onto the lipid monolayer reached a threshold value when [BSA]>5×10^-8 mol/L for all pHs. From the surface pressure-time (π-t) data, we obtained that desorption and adsorption processes occurred at pH=3, however, there was only desorption process occurring at pH=5 and 10. These results showed that the interaction mechanism between DPPG and BSA molecules was affected by the pH of subphase. BSA molecules were adsorbed onto the DPPG monolayers mainly through the hydrophobic interaction at pH=3 and 5, and the strength of hydrophobic interaction at pH=3 was stronger than the case of pH=5. At pH=10, a weaker hydrophobic interaction and a stronger electrostatic repulsion existed between DPPG and BSA molecules. AFM images revealed that the pH of subphase and [BSA] could affect the morphology features of the monolayers, which was consistent with these curves. The study provides an important experimental basis and theoretical support to understand the interaction between lipid and BSA at the air-water interface.     

Nanofibrous membrane of polyacrylonitrile with efficient adsorption capacity for cadmium ions from aqueous solution: Isotherm and kinetic studies

The nanofibrous membrane of polyacrylonitrile (NMP) was successfully synthesized after NaOH and NaHCO₃ treatment aiming its functionalization using electrospinning for cadmium ion (Cd²⁺) adsorption. Field emission scanning electron microscopy (FE-SEM) revealed that small particles attached to the surface of functionalized PAN nanofibers. Equilibrium was attained after 60 min following a rapid uptake of Cd²⁺ with maximum adsorption capacity and percentage removal at an optimum solution pH of 7.0. The adsorbent dose of 0.3 g and 90 mg L⁻¹ of initial Cd²⁺ concentration yielded the maximum adsorption capacity. The pseudo-second-order kinetic model was the best fitted to the adsorption data, indicating that the chemisorption is the controlling mechanism of adsorption. The physisorption was proposed based on the calculated values of the mean free energy of adsorption from the D–R isotherm (E < 8 kJ mol⁻¹). Furthermore, three-parameter isotherm models indicated the homogeneous and heterogeneous Cd²⁺ adsorption onto NMP adsorbent.     

N,N-Dilauryl Chitosan：Synthesis and Surface Pressure-area Isotherm

With sodium dodecyl sulfonate(SDS) as the phase transferring catalyst, N,N-Dilauryl chitosans with a high degree of alkyl group substitution were prepared and characterized by means of FTIR, ^1H NMR and elemental analyses. The results indicate that the average degree of alkyl group substitution on the chitosan increases with decreasing the molecular weight of the chitosan. The fully N,N-dilaurylated chitosan was found to be dissolvable in chloroform. The collapsed pressures of the samples derived from chitosan with 3000,5000 and 10000 dalton are 47.6, 48. 2 and 51.0 mN/m, respectively. The surface area occupied by the monomer unit(glucosamine) of all. those samples is 0:6 nm^2.     

Theoretical study of the accuracy of the pulse method,frontal analysis,and frontal analysis by characteristic points for the determination of single component adsorption isotherms

The adsorption isotherms of selected compounds are our main source of information on the mechanisms of adsorption processes. Thus, the selection of the methods used to determine adsorption isotherm data and to evaluate the errors made is critical. Three chromatographic methods were evaluated, frontal analysis (FA), frontal analysis by characteristic point (FACP), and the pulse or perturbation method (PM), and their accuracies were compared. Using the equilibrium-dispersive (ED) model of chromatography, breakthrough curves of single components were generated corresponding to three different adsorption isotherm models: the Langmuir, the bi-Langmuir, and the Moreau isotherms. For each breakthrough curve, the best conventional procedures of each method (FA, FACP, PM) were used to calculate the corresponding data point, using typical values of the parameters of each isotherm model, for four different values of the column efficiency (N=500$N=500$, 1000, 2000, and 10,000). Then, the data points were fitted to each isotherm model and the corresponding isotherm parameters were compared to those of the initial isotherm model. When isotherm data are derived with a chromatographic method, they may suffer from two types of errors: (1) the errors made in deriving the experimental data points from the chromatographic records; (2) the errors made in selecting an incorrect isotherm model and fitting to it the experimental data. Both errors decrease significantly with increasing column efficiency with FA and FACP, but not with PM.     

Adsorption of crystal violet dye from aqueous solution using mesoporous materials synthesized at room temperature

In this work, batch adsorption experiments are carried out for crystal violet dye using mesoporous MCM-41 synthesized at room temperature and sulfate modified MCM-41 prepared by impregnation method using H₂SO₄ as sulfatising agent. The surface characteristics, pore structure, bonding behavior and thermal degradation of both the MCM-41 samples are characterized by nitrogen adsorption/desorption isotherms, X-ray diffraction (XRD) patterns, Fourier transform infrared (FT-IR) spectroscopy and thermo gravimetric analysis (TGA). The adsorption isotherm, kinetics and thermodynamic parameters are investigated for crystal violet (CV) dye using the calcined and sulfated MCM-41. Results are analysed using Langmuir, Freundlich and Redlich-Peterson isotherm models. It is found that the Freundlich model is an appropriate model to explain the adsorption isotherm. The highest adsorption capacity achieved is found to be 3.4×10⁻⁴ mol g⁻¹ for the sulfated MCM-41. The percentage removal of crystal violet dye increases with increase in the pH for both the MCM-41 adsorbents. Kinetics of adsorption is found to follow the second-order rate equation. From the thermodynamic investigation, it is evident that the adsorption is exothermic in nature.