Protection of iron corrosion by stearic acid and stearic imidazoline self-assembled monolayers

A type of stearic imidazoline (IM) inhibitor was prepared using stearic acid (SA) and diethylenetriamine (DETA) as raw materials. The monolayers of IM and SA were assembled on the iron surface. The electrochemical characterization of stearic acid (SA) and stearic imidazoline (IM) on an oxide free iron surface had been studied. The monolayers of IM inhibitor were characterized by electrochemical impedance spectroscopy (EIS), electrochemical polarization curves, double layer capacitance, X-ray photoelectron spectroscopy (XPS) and molecular simulation. The results of electrochemical studies had illustrated that the inhibition efficiency of IM was higher than SA. XPS showed that the IM molecules adsorbed on the iron surface. The molecular simulation calculations showed that the IM molecules were tilted at an angle on the iron surface.     

Synthesis and magnetic properties of multilayer Ni/Cu and NiFe/Cu nanowires

Highly ordered composite nanowires with multilayer Ni/Cu and NiFe/Cu have been fabricated by pulsed electrodeposition into nanoporous alumina membrane. The diameter of wires can be easily varied by pore size of alumina, ranging from 30 to 100 nm. The applied potential and the duration of each potential square pulse determine the thickness of the metal layers. The nanowires have been characterized by transmission electron microscopy (TEM), magnetic force microscopy (MFM), and vibrating sample magnetometer (VSM) measurements. The MFM images indicate that every ferromagnetic layer separated by Cu layer was present as single isolated domain-like magnet. This technique has potential use in the measurement and application of magnetic nanodevices.     

Microstructure array on Si and SiOx generated by micro-contact printing, wet chemical etching and reactive ion etching

A method, combining micro-contact printing (μCP), wet chemical etching and reactive ion etching (RIE), is reported to fabricate microstructures on Si and SiOx. Positive and negative structures were generated based on different stamps used for μCP. The reproducibility of the obtained microstructures shows the methodology reported herein could be useful in Micro-Electro-Mechanical Systems (MEMS), optical and biological sensing applications.     

57Fe Mössbauer spectroscopic study of (25−x)MnO–xZnO–15Fe2O3–60B2O3 glasses

The ⁵⁷Fe Mössbauer technique has been used to investigate the effect of zinc oxide substitution in (25???x)MnO–xZnO–15Fe₂O₃–60B₂O₃ glass system (x?=?0, 5, 10, 15 and 20 mol% of ZnO ). Mössbauer absorption spectra for all the samples recorded at room temperature suggest the existence of the two paramagnetic quadrupole doublets. The observed variations in hyperfine parameters have been explained on the basis of cations distribution and exchange interaction at the lattice sites and it is concluded that B–B interaction increases while the metal–metal interaction decreases due to replacement of manganese oxide by zinc oxide. These results suggest that the present glass system exhibits a paramagnetic behaviour that changes towards the weak paramagnetic when manganese oxide was replaced with zinc oxide.     

Slow positron beam study of corrosion-related defects in pure iron

Corrosion-related defects of pure iron were investigated by measuring Doppler broadening energy spectra (DBES) of positron annihilation and positron annihilation lifetime (PAL). Defect profiles of the S-parameter from DBES as a function of positron incident energy up to 30 keV (i.e. ∼1 μm depth) were analyzed. The DBES data show that S-parameter increases as a function of positron incident energy (mean depth) after corrosion, and the increase in the S-parameter is larger near the surface than in the bulk due to corrosion. Furthermore, information on defect size from PAL data as a function of positron incident energy up to 10 keV (i.e. ∼0.2 μm depth) was analyzed. In the two-state trapping model, the lifetime τ₂ = 500 ps is ascribed to annihilation of positrons in voids with a size of the order of nanometer. τ₁, which decreases with depth from the surface to the bulk, is ascribed to the annihilation of positrons in dislocations and three-dimensional vacancy clusters. The corroded samples show a significant increase in τ₁ and the intensity I₂, and near the surface the corroded iron introduces both voids and large-size three-dimensional vacancy clusters. The size of vacancy clusters decreases with depth.     

Fabrication and characterization of sputtered titanium dioxide films

TiO₂ thin films were prepared under various conditions by using a reactive RF sputtering technique. The structural, optical and electrical characteristics of the films have been investigated. All as-deposited films were amorphous. After annealing at T > 673 K, the crystallinity of the observed tetragonal anatase phase appeared improved. The optical band gap, determined by using Tauc plot, has been found to amount to 3.38 ± 0.03 and 3.21 ± 0.03 eV for the direct and indirect transition, respectively. Also the complex optical constants for the wavelength range 300-2500 nm are reported. Using the two-point probe technique, the dark resistivity has been measured as a function of the film thickness, d. The resistivity, ρ, of the samples has been found to decrease markedly with increasing thickness, but only for d < 100 nm. The behaviour of ρd versus d was found to fit properly with the Fuchs and Sondheimer relation with parameters ρ_o = 4.95 × 10⁶ Ω cm and mean free path, l = 310 ± 2 nm. The log ρ versus 1/T curves show three distinct regions with values for the activation energy of 0.03 ± 0.01, 0.17 ± 0.01 and 0.50 ± 0.02 eV, respectively.     

0.18μm CMOS工艺栅极氧化膜可靠性的衬底和工艺依存性

用斜坡电压法(Voltage Ramp, V-ramp)评价了0.18μm双栅极 CMOS工艺栅极氧化膜击穿电量(Charge to Breakdown, Q_bd)和击穿电压(Voltage to Breakdown, V_bd). 研究结果表明，低压器件(1.8V)的栅极氧化膜(薄氧)p型衬底MOS电容和N型衬底电容的击穿电量值相差较小，而高压器件(3.3V)栅极氧化膜(厚氧)p衬底MOS电容和n衬底MOS电容的击穿电量值相差较大，击穿电压测试值也发现与击穿电量 关键词： 薄氧 可靠性 击穿电压 击穿电量     

The effect of ITO films thickness on the properties of flexible organic light emitting diode

Indium tin oxide (ITO) thin films were deposited on cyclic olefin copolymer substrate at room temperature by an inverse target sputtering system. The crystal structure and the surface morphology of the deposited ITO films were examined by X-ray diffraction and atomic force microscopy, separately. The electrical properties of the conductive films were explored by four-point probing. Visible spectrometer was used to measure the optical properties of ITO-coated films. The performance of the flexible organic light emitting diode device with different thickness anode was investigated in this study.     

Photo-Absorption and photochemical decomposition of copper and alkaline-earth ß-diketonates as source gases of high-Tc superconducting films

For low-temperature deposition of oxide films relating to Bi-Sr-Ca-Cu-O superconductors, photo-absorption and -decomposition properties were examined with respect to copper and alkaline-earth ß-diketonates. It was confirmed that all ß-diketonates examined were promising as source materials for photochemical vapour deposition (photo-CVD) using a low-pressure mercury lamp, in view of their large light absorption coefficients at wavelength 254 nm. The light irradiation was effective for the formation of highly crystalline oxide films at temperatures below 600 °C. By combining two sources, Ca₂CuO₃ and SrCuO₂ films were prepared. Photo-CVD of c-axis oriented Bi₂Sr₂CuO_x film was achieved by the irradiation of ternary sources of Bi(C₆H₅)₃ and strontium and copper ß-diketonates at 500 °C.     

Alloy formation in mechanically activated mixtures

The physical mixtures of hydroxocarbonates of Cu and Ni with aluminium were activated using a laboratory planetary mill. The chemical reactions and alloy formations as the effects of grinding were followed by the phase analysis of solid products based on the thermogravimetry and X-ray diffractometry. Experimental evidence indicates that the nature of reactions and products of mechanical activation was dependent on the amount of aluminium and time of grinding. This revised version was published online in July 2006 with corrections to the Cover Date.