Quaternized wood as sorbent for hexavalent chromium

The potential of quaternized wood (QW) chips in removing hexavalent chromium from synthetic solution and chrome waste under both batch and continuous-flow conditions was investigated. Sorption was found to be dependent on pH, metal concentration, and temperature. QW chips provide higher sorption capacity and wider pH range compared with untreated wood chips. The equilibrium data could be fitted into the Langmuir isotherm model, and maximum sorption capacities were calculated to be 27.03 and 25.77 mg/g in synthetic chromate solution and chrome waste, respectively. The presence of sulfate in high concentration appeared to suppress the uptake of chromium by QW chips. Column studies showed that bed depth influenced the breakthrough time greatly whereas flow rate of influent had little effect on its sorption on the column.     

聚偏氟乙烯的氯化改性

研究了聚偏氟乙烯 (PVDF)自由基引发的氯化反应。考察了各种因素 ,如氯化剂、引发剂的种类及浓度 ,反应介质、反应温度和反应时间的影响 ,确定了合成氯化PVDF的最佳反应条件。采用碱熔法测定氯含量 ,用HNMR进行了结构表征 ,并用溶度参数法、接触角法、DTA TG等方法对PVDF氯化前后的溶解性、附着力、熔点等性能进行了测试。结果表明 ,氯原子成功地引入到了PVDF上 ,当氯含量增加到 8 3 %时 ,氯化PVDF的熔点由 1 63℃降至 1 3 0℃左右 ,附着力也有了明显的改善 ,与水的接触角由 90°降至 5 4°,由不溶于丙酮变为溶于丙酮 ,对甲醇和四氯化碳的溶度参数的变化也说明了氯化PVDF的溶解性能变好 ,由TG曲线可知 ,氯化PVDF的热稳定性比改性前虽有一定的降低 ,但其分解温度仍在 3 0 0℃以上     

Modification of solids with volatile organics III: Natural zeolites

Summary The effect of pre-adsorbed benzene and ethanol on the adsorptive properties of natural zeolite (clinoptilolite) has been studied by gas-solid chromatography. It has been shown that modification of the solid surface by volatile organics has a significant influence on the adsorptive properties. The modification is of the same order as the more difficult modification by inorganics, as illustrated here by clinoptilolite modification with Co²⁺. Energy distribution of surface adsorptive sites appears to be continuous and confirms previous finding that only a small proportion of active sites is responsible for most adsorbate retention. Part II reference [4]     

Synthesis and Characterization of a Novel Biomaterial： Maleic Anhydride-modified Poly（dl-lactic acid）

A novel modified poly(dl-lactic acid) (PDLLA) was obtained by covalently grafting of maleic anhydride onto the backbone of PDLLA, attempting to improve PDLLA‘s hydrophilicity and cell affinity and to provide reactive groups for further chemical modification. FTIR, ^13 C NMR and DSC were used to characterize the maleic anhydride-modified PDLLA.     

Synthesis of the Biomimetic Polymer： Aliphatic Diamine and RGDS Modified Poly（d,l-lactic acid）

A novel poly（d, /-lactic acid） （PDLLA） based biomimetic polymer was synthesized by grafting maleic anhydride, butanediamine and arg-gly-asp-ser （RGDS） peptides onto the backbone of PDLLA, aiming to overcome the acidity and auto-accelerating degradation of PDLLA during degradation and to improve its biospecificity and biocompatibility. The synthetic copolymer was characterized by FTIR, ^13C NMR and amino acid analyzer （AAA）.     

KIT-1介孔分子筛的化学修饰及吸附性能

介孔分子筛MCM-41具有较大、可调的孔径和较高的比表面积，其骨架组成具有较强的可调变性．为该材料的应用提供了很大的空间。但全硅MCM-41分子筛在潮湿空气中，即使在室温条件下也会发生水解反应，使其介孔结构遭到破坏。前人已针对MCM-41分子筛稳定性不足的问题相继合成了稳定性较高的介孔分子筛KIT-1,     

Surface structure and electrochemical characteristics of natural graphite fluorinated by ClF3

Natural graphite samples with average particle sizes of 5, 10 and 15 μm (NG5 μm, NG10 μm and NG15 μm, respectively) were fluorinated by ClF₃ (3 × 10⁴ Pa) at 200 and 300 °C for 2 min. X-ray photoelectron spectra of surface-fluorinated samples showed that surface fluorine concentration increased with increase in the particle size of graphite and reaction temperature. Small amounts of chlorine were also detected in all the fluorinated samples. Raman spectra of original and surface-fluorinated samples indicated that the surface disordering was increased for NG10 μm and NG15 μm. Surface areas were decreased by the fluorination for NG5 μm and NG10 μm but unchanged for NG15 μm. The mesopores with diameter of 1.5-2 nm increased while those of 2-3 nm decreased for all the samples. First coulombic efficiencies for NG10 μm and NG15 μm were highly increased by surface fluorination in 1 mol/dm³ LiClO₄-EC/DEC/PC (EC: ethylene carbonate, DEC: diethyl carbonate, PC: propylene carbonate) solution.     

Zur Struktur und Reaktivität des Diammoniumhexafluoromanganats(IV)

About the Structure and Reactivity of Diammonium Hexafluoromanganate(IV) Electrolytic oxidation of an aqueous suspension of MnF₂ containing NH₄F, and subsequent crystallization in 40% HF yields yellow crystals of (NH₄)₂MnF₆. It crystallizes in the hexagonal K₂MnF₆ type structure with the space group P6₃mc and a = 5.903; c = 9.565 Å; Z = 2. With in situ powder diffraction studies it is shown, that (NH₄)₂MnF₆ is gradually reduced in a NH₃ atmosphere between 30 and 230 °C to afford (NH₄)₃MnF₆, (NH₄)₂MnF₅, and finally NH₄MnF₃. (NH₄)₃MnF₆, thereby, forms a hitherto unknown cubic (a = 9.082 Å) high temperature modification with the cryolite type structure. Under N₂ the thermal decomposition of (NH₄)₂MnF₆ proceeds via NH₄MnF₄ to yield MnF₂.     

Surface modification of low density polyethylene (LDPE) film by low pressure O2 plasma treatment

In this work, low pressure glow discharge O₂ plasma has been used to increase wettability in a LDPE film in order to improve adhesion properties and make it useful for technical applications. Surface energy values have been estimated using contact angle measurements for different exposure times and different test liquids. In addition, plasma-treated samples have been subjected to an aging process to determine the durability of the plasma treatment. Characterization of the surface changes due to the plasma treatment has been carried out by means of Fourier transformed infrared spectroscopy (FTIR) to determine the presence of polar species such as carbonyl, carboxyl and hydroxyl groups. In addition to this, atomic force microscopy (AFM) analysis has been used to evaluate changes in surface morphology and roughness. Furthermore, and considering the semicrystalline nature of the LDPE film, a calorimetric study using differential scanning calorimetry (DSC) has been carried out to determine changes in crystallinity and degradation temperatures induced by the plasma treatment. The results show that low pressure O₂ plasma improves wettability in LDPE films and no significant changes can be observed at longer exposure times. Nevertheless, we can observe that short exposure times to low pressure O₂ plasma promote the formation of some polar species on the exposed surface and longer exposure times cause slight abrasion on LDPE films as observed by the little increase in surface roughness.     

Copper ring-disk microelectrodes: fabrication, characterization, and application as an amperometric detector for capillary columns

A novel approach to the fabrication of metal ring-disk (RD) microelectrodes is presented that employs flexible chemical vapor deposition (CVD) and electrode modification techniques. Specifically, the development of a copper ring-disk microelectrode is described utilizing a combination of CVD coating, electroetching, and electroplating. Initially, a 25 μm diameter tungsten wire is concentrically coated by CVD with an insulating layer of silica, a layer of tungsten metal, and finally, a second outer layer of silica. The copper surface was prepared by first creating micrometer cavities by electrochemical etching the tungsten in hydroxide solutions followed by electrodeposition of copper from aqueous solutions of Cu(II). Each step of the process was characterized by scanning electron microscopy, optical microscopy, and cyclic voltammetry, demonstrating the preparation of a viable metal-based dual ring-disk microelectrode system. For the purpose of demonstrating the concept of introducing specific selectivity into the device, amperometric detection of galactose in 0.1 M NaOH was performed at +0.60 V in bulk solution and after flow injection analysis in a capillary column.