液相色谱-电喷雾质谱法分析脂肪醇聚氧乙烯醚硫酸钠

采用电喷雾质谱(ESI/MS)技术建立了脂肪醇聚氧乙烯醚硫酸钠(AES)的烷基碳链分布、乙氧基分布及平均EO数、平均相对分子质量的测定方法;采用液相色谱-电喷雾质谱(LC-ESI/MS)测定了AES中的游离十二烷基硫酸钠(SDS)的含量。将本方法应用于实际样品的测定,并与核磁共振法测得的平均EO数进行比较,二者的测定结果相当吻合,从而验证了本法的可靠性。     

ICP-AES法测定油漆涂层中总铅含量的不确定度评定

根据EURACHEM/C ITAC 2000中的规定评定了ICP-AES法测定油漆中总铅含量的不确定度。结果表明,标准曲线拟合线性方程、标准工作液配制过程、样品重复性分析及消化过程中消化回收率是不确定度的主要来源。油漆涂层中的可溶性铅的检测结果可表示为:(162.7±19.0)mg/kg(k=2)。     

Surface study of cerium oxide based coatings obtained by cathodic electrodeposition on zinc

A surface study of electrodeposited cerium oxide based coatings is presented. Different surface analytical techniques were used in order to obtain complementary information to fully characterize such complex systems. X-ray Photoelectron Spectroscopy was used as the main technique to determine the surface composition of the coating. The analysis of the core level peaks of the elements provides additional information about the functional groups present on the surface. A mixture of Ce (III) and Ce (IV) was found in the coating and their proportion was calculated at different depths. The analysis of the O 1s core level peak revealed a triple structure whose origin will be discussed. To support the results obtained, electron stimulated desorption was performed. The study was completed with Auger electron spectroscopy and Raman spectroscopy, both techniques having different surface sensitivities. From all these results, it is derived that incomplete electrochemical reactions occurred during the growth of the coatings. This led to rather complex compositions, in which defective cerium oxides are the major species. In addition, hydroxides, carbonates and nitrates are also present, together with adsorbed water.     

Synthesis of Cholesteryl Esters of Heterocyclic Analogs of Cinnamic Acid and Hetaroyloxycinnamic Acids by the Wittig Reaction

The reaction of cholesteryl triphenylphosphonioacetate chloride with heterocyclic aldehydes and hetaroyloxyarenecarbaldehydes in the presence of base gave the corresponding cholesteryl esters of substituted propenoic acids possessing liquid crystal properties.     

Phosphorus as sintering activator in powder metallurgical steels: characterization of the distribution and its technological impact

Powder metallurgy is a highly developed method of manufacturing reliable ferrous parts. The main processing steps in a powder metallurgical line are pressing and sintering. Sintering can be strongly enhanced by the formation of a liquid phase during the sintering process when using phosphorus as sintering activator. In this work the distribution (effect) of phosphorus was investigated by means of secondary ion mass spectrometry (SIMS) supported by Auger electron spectroscopy (AES) and electron probe micro analysis (EPMA). To verify the influence of the process conditions (phosphorus content, sintering atmosphere, time) on the mechanical properties, additional measurements of the microstructure (pore shape) and of impact energy were performed. Analysis of fracture surfaces was performed by means of scanning electron microscopy (SEM). The concentration of phosphorus differs in the samples from 0 to 1% (w/w). Samples with higher phosphorus concentrations (1% (w/w) and above) are also measurable by EPMA, whereas the distributions of P at technically relevant concentrations and the distribution of possible impurities are only detectable (visible) by means of SIMS. The influence of the sintering time on the phosphorus distribution will be demonstrated. In addition the grain boundary segregation of P was measured by AES at the surface of in-situ broken samples. It will be shown that the distribution of phosphorus depends also on the concentration of carbon in the samples.     

Surface oxidation behavior of MgNd alloys

The oxidation kinetics of MgNd alloys oxidized in pure O₂ at high temperatures has been investigated. The results revealed two stages of the reaction: A fast initial oxidation was followed by a slow oxide growth with a parabolic kinetics. For MgNd alloys (Nd = 25 wt.%), the oxidation rate increased with the enhancement of the oxidation temperature. A sudden ignition was found for this alloys oxidized at 873 K up to about 80 min. Moreover, the increase of the Nd content would harm the oxidation resistance of the MgNd alloys. By Auger electron spectroscopy (AES), X-ray photoelectron spectroscopy (XPS), X-ray diffraction (XRD) and scanning electron microscopy (SEM) analysis, it was found that a triplex structure of oxide film formed. The outer layer was composed of MgO, Nd₂O₃ and Nd(OH)₃, the middle layer mainly consisted of MgO and Nd₂O₃, and the inner layer was the transitional layer made of MgO, Nd₂O₃ and the content of the substrate. The protective oxidation was associated with the formation of the dense Nd₂O₃/MgO layer during isothermal oxidation process. The oxidation mechanisms for the formation of oxide film are discussed.     

Auger electron spectroscopic study of CO2 adsorption on Zircaloy-4 surfaces

We investigate the adsorption of CO₂ onto Zircaloy-4 (Zry-4) surfaces at 150, 300 and 600 K using Auger electron spectroscopy (AES). Following CO₂ adsorption at 150 K the graphitic form of carbon is detected, whereas upon chemisorption at 300 and 600 K we detect the carbidic phase. As the adsorption temperature is increased, the carbon Auger signal increases, whereas the oxygen signal decreases. Adsorption at all three temperatures results in a shift of the Zr Auger features, indicating surface oxidation. The effect of adsorbed CO₂ on the Zr(MVV) and Zr(MNV) transitions depends on adsorption temperature and is less pronounced at higher temperatures. On the other hand, changes in the Zr(MNN) feature are similar for all three adsorption temperatures. The changes in the Zr Auger peak shapes and positions are attributed to oxygen from dissociated CO₂, with the differences observed at various temperatures indicative of the diffusion of oxygen into the subsurface region.     

CID-ICP-AES用于高纯试样的分析性能

研究了CID-IP-AES用于测定高纯物质的分析性能。以高纯LiOH为对象，研究了低浓度范围内分析线的选择，标准曲线的特性，探讨了直接用于高纯物质分析的检测能力及可行性。     

About the Importance of Nanometer-Thick Intergranular Penetration in the Analysis of Liquid Metal Embrittlement

Liquid metal embrittlement (LME) of copper by liquid bismuth is investigated at 300°C. It is shown that a very rapid damage is due to the synergy between the external stress and the phenomenon of intergranular penetration (IGP). Tests of IGP, i.e. without external stress, were done at 300°C and at 600°C and have resulted in strong intergranular embrittlement due to the formation of nanometer-thick intergranular films, as measured and quantified by Auger electron spectroscopy (AES). The formation of these films is discussed with respect to apparently non-zero dihedral angles at 600°C. A general procedure based on mechanical testing and AES measurements, to check whether IGP has occurred or not, is outlined. This procedure can be seen as an alternative way to determine the wetting transition temperature. The presence of nanometer-thick films due to IGP is discussed with respect to the LME mechanisms.     

电感耦合等离子体原子发射光谱法测定电解金属锰中硒、铁、硅

本文采用稀硫酸溶解试样，ICP－AES法同时测定电解金属锰中硒、铁、硅，通过对溶样酸、锰基体以及背景的研究，确定了分析条件。该方法简便具有良好的精密度和准确性，相对标准偏差不大于2．68％，回收率为98％－105％。经t检验与经典法无显著性差异。