Determination of the degree of cure under dynamic and isothermal curing conditions with electrical impedance spectroscopy

This article presents a new methodology for the quantitative determination of the progress of the curing reaction of a thermosetting resin, using the results of electrical impedance spectroscopy. The method is an extension of the use of the imaginary impedance maximum as a reaction progress indicator and is based on the demonstration of a close correlation between the reaction rate, as measured by conventional differential scanning calorimetry, and the rate of change of the value of the imaginary impedance spectrum maximum. Tests on a commercial aerospace epoxy resin under both isothermal and dynamic heating conditions with calorimetry and impedance spectroscopy have demonstrated the validity of the method and set the accuracy limits involved. This technique can be used as a real-time online control tool for thermoset composite manufacturing. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 146–154, 2004     

Novel fixed‐site–carrier polyvinylamine membrane for carbon dioxide capture

Fixed‐site–carrier membranes were prepared for the facilitated transport of CO₂ by casting polyvinylamine (PVAm) on various supports, such as poly(ether sulfone) (PES), polyacrylonitrile (PAN), cellulose acetate (CA), and polysulfone (PSO). The cast PVAm on the support was crosslinked by various methods with glutaraldehyde, hydrochloric acid, sulfuric acid, and ammonium fluoride. Among the membranes tested, the PVAm cast on polysulfone and crosslinked by ammonium fluoride showed the highest selectivity of CO₂ over CH₄ (>1000). The permeance of CO₂ was then measured to be 0.014 m³ (STP)/(m² bar h) for a 20 μm thick membrane. The effect of the molecular weight of PVAm and feed pressure on the permeance was also investigated. The selectivity increased remarkably with increasing molecular weight and decreased slightly with increased pressure in the range of 1 to 4 bar. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 4326–4336, 2004     

Statistical thermodynamics evaluation of polymer–polymer miscibility

The Simha and Somcynsky (S–S) statistical thermodynamics theory was used to compute the solubility parameters as a function of temperature and pressure [δ = δ(T, P)], for a series of polymer melts. The characteristic scaling parameters required for this task, P*, T*, and V*, were extracted from the pressure–temperature–volume (PVT) data. To determine the potential polymer–polymer miscibility, the dependence of δ versus T (at ambient pressure) was computed for 17 polymers. Close proximity of the δ versus T curves for four miscible polymer pairs: PPE/PS, PS/PVME, and PC/PMMA signaled the usefulness of this approach. It is noteworthy, that the tabulated solubility parameters (derived from the solution data under ambient conditions) propounded the immiscibility of the PVC/PVAc pair. The computed values of δ also suggested miscibility for polymer pairs of unknown miscibility, namely PPE/PVC, PPE/PVAc, and PET/PSF. In recognizing the limitations of the solubility parameter approach (the omission of several thermodynamic contributions), these preliminary results are auspicious because they indicate a new route for estimating the miscibility of any polymeric material at a given temperature and pressure. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 2909–2915, 2004     

NMR investigation of concentrated alumina and silica slurries

The longitudinal relaxation times (T₁) of water in concentrated silica and alumina slurries were measured as a function of solids content. It was shown that the results could be fit very well with a two-phase fast-exchange model between free and surface-bound water. As expected, values of T₁ for bound water were in the order of 20–2000 times lower than that for free water, indicating a higher effective viscosity of the surface-bound water. The strength of the interaction depended on the particular surface, and all of the aluminas examined interacted more strongly with water than the two silicas studied, which themselves differed considerably. The chemical mechanical polishing (CMP) removal rate of tantalum by silica slurries was shown to be directly correlated with the interaction parameters, derived from the NMR relation times rather than with total surface hydroxyl group concentration.     

On the influence of the surfactant''s polar group on the local and terminal velocities of bubbles

The local and the terminal velocities, the size and the degree of bubbles’ shape deformations were determined as a function of distance from the position of the bubble formation (capillary orifice) in solutions of n-octyltrimethylammonium bromide, n-octyldimethylphosphine oxide, n-octyl-β-D-glucopyranoside and n-octanoic acid.

These surface-active compounds have different polar groups but an identical hydrocarbon chain (C8) in the molecule. The motion of the bubbles was monitored and recorded using a stroboscopic illumination, a CCD camera, and a JVC professional video. The recorded bubble images were analyzed by the image analysis software. The bubbles accelerated rapidly and their shape was deformed immediately after detachment from the capillary. The extent of the bubbles’ shape deformation (ratio of horizontal and vertical diameters) was 1.5 in distilled water and dropped rapidly down to a level of ca. 1.05–1.03 with increasing surfactant concentration. After the acceleration period the bubbles either attained a constant value of the terminal velocity (distilled water and high concentrations of the solutions), or a maximum in the velocity profiles was observed (low concentrations). The values of the terminal velocity diminished drastically with increasing concentration, from the value of 35 cm/s in water down to about 15 cm/s, while the bubble diameter decreased by ca. 10% only. The surfactant adsorption at the surface of the bubbles was evaluated and the minimum adsorption coverages required to immobilize the bubbles’ surface were determined. It was found that this minimum adsorption coverage was ca. 4% for n-octyldimethylphosphine oxide, n-octyl-β-D-glucopyranoside, n-octanoic acid and 25% for n-octyltrimethylammonium bromide. The difference in the adsorption coverage together with the surfactants’ surface activities indicate that it is mainly the adsorption kinetics of the surfactants that governs the fluidity of interfaces of the rising bubbles.     

光学非球面二次曲面常数及顶点曲率的研究

受光学非球面制造过程中诸工艺参数的影响,能否保证非球面顶点曲率及二次曲面常数的精度是一个重要问题。基于二次曲面方程,推导出确定光学非球面二次曲面常数k以及顶点曲率半径r的一组算法,并在对一块口径为760mm×200mm标准非球面反射镜的实际测算中进行拟合,经过优化,拟合精度达到Δk=0.015,Δr=0.341mm,从而有效的控制了光学非球面制造过程中的顶点曲率及二次曲面常数的偏差。     

爆磁压缩发生器通过脉冲变压器对脉冲形成线充电的理论分析

 将爆磁压缩等效为电流源的方法，对爆磁压缩发生器通过脉冲变压器对脉冲形成线充电进行了理论分析，得出爆磁压缩发生器在负载上产生电流波形（简称负载电流）为直线情况和任意电流波形情况下充电电流和充电电压的表达式。分析表明变压器耦合互感与负载电流随时间变化增长率是脉冲形成线充电的两个重要参数，脉冲形成线第一个充电电压峰值与变压器的耦合互感和负载电流波形斜率成正比，负载电流波形斜率的变化可以改变充电电压峰值的时间，斜率不断增加可以延长第一个充电电压峰值时间，从而可能增加充电电压的幅值，提高爆磁压缩发生器能量的利用效率。     

一种新的永久周期磁铁聚焦的高功率宽带放大器

 提出了一种新的高功率宽带放大器，它由速调管和自由电子脉塞组成，用永久周期磁铁聚焦。研究了这种器件的电子束聚焦、群聚和辐射。在速调管提供一阶调制系数为30%，波导管的半径1.51cm，摇摆器的磁场振幅0.16T，周期7.92cm，电子束的电压490kV，电流50A和半径0.368cm的条件下，预估这种器件的辐射波频率为11.4GHz，输出辐射功率为18MW，输出辐射带宽为44%。     

PURIFICATION OF L-METHIONINE AND N-ACETYL-D-METHIONINE FROM THE MIXTURE OF ENZYMATICALLY DEACYLATED N-ACETYL-DL-METHIONINE

1. INTRODUCTION Methionine, namely 2-amido-4-thiomethyl butyric acid with a structure of CH3SCH2CH2CHCOOH, is one of the essential amino acids and has two natural enantionmers, D and L-methionine. The mixture of L- and D-isomers can be used as analeptics or nutritive additives to maintain the equilibrium of amino acids of feed [1,2]. L-methionine can release active methyl and accelerate the synthesis of choline, which further speeds up the conversion of the lipid accumulated in liv…     

Synthesis of New 13-O-Acylavermectin Bl Aglycones

Six new 13-O-acylavermectin Bl aglycones(3-8) were synthesized from avermectin B1 aglycone and their bioactivities were evaluated against Spodoptera exigua, Spodoptera eridania, Tetranychus urticae and Aphis fabae.