Mass distribution in a dynamic sample zone inside a flow injection manifold: modelling integrated conductimetric profiles

A mathematical model for fitting the experimental ICM (integrated conductimetric method) curves developed by the authors in a previous work, is presented for the first time in this study. The proposed model fits the experimental curves with great precision and allows to predict physical dispersion for single-line flow injection system. The correlation of the model’s parameters with typical reactionless FIA peak parameters is also assessed. The IDQ coefficient—a novel dispersion estimator previously reported by the authors—can also be predicted when operational FIA variables are changed. Experimental and modelled profiles are compared as a function of the system’s variables, showing an excellent agreement.     

Splitless injection of up to hundreds of microliters of liquid samples in capillary GC: Part II,experimental results

Sample evaporation in splitless injection of large volumes is rapid: depending on the experiment, results indicate that 200 μl of hexane, for instance, evaporates in 2–10 s, producing vapor at a rate of many hundreds of milliliters per minute. A 60 × 4 mm packed bed of 20–35 mesh Tenax TA enabled injection of 200 μl volumes of all solvents tested, and even 1 ml injections were possible provided they were performed over a period of 30 s. Retention of volatile sample components depends on the sample solvent, the injection volume, and the injection speed, but only little on the injector temperature. Losses of n-tridecane varied from hardly 15 % (when dissolved in pentane) to ca 60 % (ethyl acetate); losses of n-heptadecane were usually below 20 %. The column temperature during injection should be at least ca 20–30°C above the standard solvent boiling point.     

Thin layer distillation for matrix isolation in flow analysis

Analyte transfer from the matrix in a thin layer distillation (TLD) cell and its subsequent measurement were investigated in a flow injection configuration. We designed the cell such that the donor and acceptor streams flowed in parallel channels separated by a thin dividing wall. The matrix transfer process involved room-temperature distillation of the analyte into the headspace of the TLD cell and its subsequent condensation/uptake by a concurrently flowing acceptor stream. There are no membranes; hence there are no membrane-related problems. The TLD system design was optimized with respect to its dimensions and operational parameters. Throughput and sensitivity were compared with a conventional pervaporation flow injection (PFI) system for ammonia and five different amines. For the higher molecular mass amines, the TLD approach provided comparable or superior performance. The TLD technique should be an attractive approach for online analysis of volatile chemical species in ‘dirty’ samples, especially for volatile analytes of higher molecular mass.     

The impact of flow injection on modern chemical analysis: has it fulfilled our expectations? And where are we going?

Presenting a condensation of the opening lecture of the 12th ICFIA conference, this communication presents a view of the impact that flow injection analysis (FIA) has had on modern analytical chemistry, evaluated both within the academic community and outside it, i.e. in “industry”. The ensuing developments of FIA, encompassing sequential injection analysis (SIA) and bead injection lab-on-valve (BI-LOV), are described and their individual features discussed. Finally, some recent results of the activities from the author’s own research group are briefly mentioned.     

Amperometric detection of hydrazine by cyclic voltammetry and flow injection analysis using ruthenium modified glassy carbon electrodes

Glassy carbon electrodes modified with (5-amino-1,10-phenanthroline)bis(bipyridine)ruthium(II) chloride hydrate, [(bpy)₂Ru(5-phenNH₂)]Cl₂·H₂O, are shown to oxidize hydrazine with excellent sensitivity. The presence of an amine group on the ruthenium complex facilitates electropolymerization onto the electrode surface. Using cyclic voltammetry, a large catalytic current is observed upon oxidation of hydrazine in phosphate buffer (pH 5.0), compared to the current obtained from the ruthenium-modified electrode with no hydrazine present. The sensitivity of cyclic voltammetry is sufficient for obtaining a linear calibration curve for hydrazine over the range of 10⁻⁵ to 10⁻² M. Hydrodynamic amperometry was used to determine the working potential for flow injection analysis. The limit of detection for hydrazine was determined to be 8.5 μM using FIA. The thickness of these films was shown to increase linearly with the number of electropolymerization cycles, in the range of 1000-2500 nm for 5-20 cycles, respectively, using Rutherford backscattering spectrometry (RBS). RBS analysis also suggests that the film is multilayered with the outermost layers containing a high ruthenium concentration, followed by layers where the concentration of ruthenium decreases linearly and approaches zero at the electrode surface.     

A perylenedicarboxamide linker for DNA hairpins

The synthesis and properties of a perylenediamide diol linker and several DNA hairpins possessing this linker are described. The diol linker absorbs and fluoresces strongly in the visible. Hairpins having poly(dA)-poly(dT) stems have fluorescence quantum yields and decay times similar to those of the linker, indicating that hole injection does not occur from the singlet excited linker into the base pair domain. Fluorescence quenching by dG or dZ bases is observed when these bases are located near the linker. The strong distance dependence of fluorescence quenching is consistent with a superexchange mechanism for electron transfer. Failure to observe formation of the linker anion radical by means of femtosecond time resolved absorption spectroscopy is attributed to fast charge recombination. The properties and behavior of the perylene linker and its hairpins are compared to those of other arenedicarboxamide linkers.     

反应注射成型聚氨酯互穿聚合物网络研究——刚性网络对于体系形态及性能的影响

用微型反应注射成型机制备了以聚氨酯(PU)为弹性相的两类同步互穿聚合物网络(SIN),其刚性相分别采用保留仲羟基的乙烯基酯树脂(VERH)以及封闭仲羟基的乙烯基酯树脂(VERA)。用傅里叶变换红外光谱在线跟踪了这类互穿网络的生成过程,发现刚性网络抑制了PU网络中硬段有序结构的形成,两个网络间有一定程度的互穿,而两个网络间的化学键作用进一步削弱氢键强度。自旋—自旋弛豫时间的测定进一步表明网络间存在一定的互穿以及刚性相对于PU硬段结晶的抑制作用。材料的力学性能与其SIN的形态有关。VERA网络对PU表现出明显的增强作用,而由VERH网络形成的SIN则由于体系相分离进程受到严重阻碍而使材料性能恶化。     

工业废水中微量铜（Ⅱ）和氰化物的流动注射光度分析

采用ＦＩＡ技术，以光度比色法为基础，建立了工业废水中微量Ｃｕ＾２＋和ＣＮ＾－的顺序自动分析方法和装置。其对二种离子的测定频率为６０样／ｈ，相对标准偏差＜１．０％，工作曲线的ｒ值≥０．９９９，各项分析技术指标均优于手工法操作。     

Solventless injecction for packed column supercritical fluid chromatography

The adverse effects of injection solvent strength on microbore packed column SFC band broadening are demonstrated and a solventless injection system that eliminates these effects is introduced. The injection system removes solvent in a GC-like manner using a retention gap and an on-column capillary GC syringe. The analyte is delivered to the analytical column in a solvent-free plug of supercritical fluid mobile phase.     

Flow injection-spectrophotometric determination of cresol compounds in water by reaction withp-aminophenol

A spectrophotometric method has been developed for the simultaneous determination ofo-cresol andm-cresol in water by reaction withp-aminophenol (PAP). Three different methodologies have been assayed; (i) batch analysis, after reaction in an alkaline medium in the presence of dissolved molecular oxygen as oxidizing agent, (ii) a stopped-flow procedure, carried out in the presence of KIO₄ and (iii) a flow injection method based on the same approach. The batch procedure requires 22 min for the full development of colour witho-cresol and 12 min form-cresol. In the stopped-flow mode, using KIO₄ and a reaction time of 12 min, better sensitivity can be obtained for both compounds and limits of detection of 10 g 1^–1 foro-cresol and 30 g 1^–1 form-cresol were found. The flow injection method has a lower sensitivity but permits more than 80 injections per hour. Based on the different maximum absorbance wavelengths obtained for the reaction products of PAP witho-cresol (614 nm) andm-cresol (632 nm), both compounds can be simultaneously determined in water samples and recoveries of 90 to 115% were found in spiked water samples of different types.