A novel fiber Bragg grating high-temperature sensor

A novel fiber Bragg grating (FBG) sensor for the measurement of high temperature is proposed and experimentally demonstrated. The interrogation system of the sensor system is simple, low cost but effective. The sensor head is comprised of one FBG and two metal rods. The lengths of the rods are different from each other. The coefficients of thermal expansion of the rods are also different from each other. The FBG will be strained by the sensor head when the temperature to be measured changes. The temperature is measured basis of the wavelength shifts of the FBG induced by strain. A dynamic range of 0–800 °C and a resolution of 1 °C have been obtained by the sensor system. The experiment results agree with theoretical analyses.     

Application of multivariate analysis of TOF-SIMS spectra for studying the effect of high glucose intake on aortic lipid profile

Aim

To study the effect of long-term glucose feeding on aortic lipid composition by using the time of flight-secondary ion mass spectrometry (TOF-SIMS).

Method

Rats were divided into two groups, drinking water with or without 10% glucose from birth to 6 months of age. The aortic wall was dissected out, high-pressure frozen, freeze-fractured, freeze-dried and analyzed by TOF-SIMS using a Bismuth cluster ion source. Surface spectra were taken from standardized regions of the vessel wall.

Results

Different peaks, such as cholesterol, fatty acids (FAs) and diacylglycerols (DAGs), were identified by the principal component analysis as carries of variance between two groups. These peaks were then compared by conventional t-test. Our data showed that the intensity of cholesterol, but not FAs and DAGs, was significantly decreased in the glucose-drinking rat. Moreover, the long-term glucose intake changed ratios between different FAs in the aorta.

Conclusion

The long-term glucose intake led to decreased cholesterol intensity in the aortic wall and this effect was revealed through a global analytical approach with objective selection of significant variables.     

Effect of Resonator Parameters on Frequency and Quality Factor of Gyrotron Resonators

The influence of some cavity parameters on the resonance frequency and quality factor is investigated with the aim of comparing various methods of optimization. As an example, the geometry of the designed resonator for an experiment on a multifrequency gyrotron that would operate at 140 GHz in the TE_22,8 mode is considered. This is a weakly–tapered conventional cavity resonator with parabolic–roundings. The influence of the roundings on the quality factor is at least as important as that of the cavity length and the output taper angle.     

Metamaterial Superstrate and Electromagnetic Band-Gap Substrate for High Directive Antenna

A high directive planar antenna made from a metamaterial superstrate and an electromagnetic band-gap (EBG) substrate has been investigated. A patch antenna surrounded with EBG structures is used as the radiation source. The CST Microwave Studio is used for the simulation. The results show that the gain of the antenna with metamaterial is 21.6 dB at the operating frequency of 14.6 GHz. Compared with the patch feed with the same aperture size but without the metamaterial superstrate, the performance of the antenna is improved obviously and the gain increases about 12.4 dB.     

Pressure-induced phase transition and stability of EuO and EuS with NaCl structure

We have predicted the phase transition pressures and corresponding relative volume changes of EuO and EuS having NaCl-type structure under high pressure using three-body interaction potential (TBIP) approach. In addition, the conditions for relative stability in terms of modified Born criterion has been checked. Our calculated results of phase transitions, volume collapses and elastic behaviour of these compounds are found to be close to the experimental results. This shows that the inclusion of three-body interaction effects makes the present model suitable for high pressure studies.      

Annealing dependence of magnetic properties in nanostructured Sm0.5Y0.5Co5

Nanocrystalline Sm_0.5Y_0.5Co₅ powders with high coercivity H_C and enhanced remanence M_r were prepared by mechanical milling and subsequent annealing. Annealing temperatures T ranging from 973 to 1173 K, and times t ranging from 1 to 5 min were used. X-ray diffraction (XRD) and DC-magnetization measurements were carried out to study the microstructure and magnetic properties of these samples. XRD patterns demonstrate that the average grain size D of the nanocrystalline powders depends on the annealing temperature T and time t: D ranges from 11 nm (for T=973 K and t=1 min) to 93 nm (for T=1173 K and t=5 min). Magnetic measurements performed at room temperature indicate high coercivity values (H_C>955 kA/m), and enhanced remanence (M_r/M_max>0.5) for all samples. A strong annealing-induced grain size dependence of these magnetic properties was found.     

Magnetic properties of YCo5 (70%wt)+Y2Co17 (30%wt) nanocomposite powders at low temperatures

Nanostructured YCo₅ (70%wt)+Y₂Co₁₇ (30%wt) composite powders were prepared by mechanical milling and subsequent annealing at 1073 K for 1.5 min. The average grain size D of the YCo₅ and Y₂Co₁₇ phases, obtained from XRD data, was 14 and 12 nm, respectively. The temperature dependence of the magnetic properties was studied by DC magnetization measurements at temperatures T ranging from 3 to 300 K. Hysteresis loops (H_max=70 kOe) show that both the coercivity H_C and the squareness σ_r/σ_max are temperature-dependent. The coercivity increases from 12 kOe at room temperature to 18 kOe at T=3 K. The observed enhanced remanence (σ_r/σ_max>0.5) indicates that a strong exchange coupling is present at all temperatures used in this study. The maximum magnetization σ_max changes little with temperature and has a value of about 70% of the effective saturation magnetization of the title compound.     

High-temperature ferromagnetism in cobalt-doped ZnO single-crystalline nanorods

Co-doped ZnO single-crystalline nanorods with 80–100 nm in diameter and 1.5–2 μm in length have been prepared in a simple solution route. X-ray diffraction data and selected area electron diffraction pattern of the diluted magnetic semiconductor nanorods confirm the single crystallinity of Zn_1−xCo_xO solid solution without impurities of metallic Co or other phases. Magnetic results show that the Zn_0.95Co_0.05O nanorods exhibit a ferromagnetic characteristic with Curie temperature higher than 380 K. The high-temperature ferromagnetic properties allow this Zn_1−xCo_xO nanorods potential applications in future spintronic devices.     

Hard magnetic properties in Pr2Fe14B/α-Fe nanocomposite magnets with a combined addition of V and C

Nanostructured Pr₈Fe_86−xV_xB_6−yC_y (x=0, 1; y=0, 1) ribbons composed of Pr₂Fe₁₄B and α-Fe phases with a high coercivity are fabricated by direct melt spinning. The effects of a single addition of V and a combined addition of V and C on the structures and magnetic properties of melt-spun Pr₈Fe₈₆VB_6−xC_x (x=0 and 1) ribbons have been investigated. Compared with addition-free ribbons, 1 at% V addition is found to reduce the grain sizes of the samples and improve their magnetic properties due to a strong exchange coupling between the hard and the soft phase. A remanence ratio of 0.82, a coercive field of 6.2 kOe and a maximum energy product of 23.4 MGOe in melt-spun Pr₈Fe₈₅VB₆ ribbons are obtained at room temperature. The combined addition of V and C is found to lead to the formation of an intermediate phase of VC at grain boundaries, which appears as a pinning barrier during magnetization and results in an increase of the coercivity value to 6.9 kOe for melt-spun Pr₈Fe₈₅VB₅C ribbons.     

In vitro study of magnetic particle seeding for implant assisted-magnetic drug targeting

The concept of using magnetic particles (seeds) as the implant for implant assisted-magnetic drug targeting (IA-MDT) was analyzed in vitro. Since this MDT system is being explored for use in capillaries, a highly porous (ε∼70%), highly tortuous, cylindrical, polyethylene polymer was prepared to mimic capillary tissue, and the seeds (magnetite nanoparticles) were already fixed within. The well-dispersed seeds were used to enhance the capture of 0.87 μm diameter magnetic drug carrier particles (MDCPs) (polydivinylbenzene embedded with 24.8 wt% magnetite) under flow conditions typically found in capillary networks. The effects of the fluid velocity (0.015–0.15 cm/s), magnetic field strength (0.0–250 mT), porous polymer magnetite content (0–7 wt%) and MDCP concentration (C=5 and 50 mg/L) on the capture efficiency (CE) of the MDCPs were studied. In all cases, when the magnetic field was applied, compared to when it was not, large increases in CE resulted; the CE increased even further when the magnetite seeds were present. The CE increased with increases in the magnetic field strength, porous polymer magnetite content and MDCP concentration. It decreased only with increases in the fluid velocity. Large magnetic field strengths were not necessary to induce MDCP capture by the seeds. A few hundred mT was sufficient. Overall, this first in vitro study of the magnetic seeding concept for IA-MDT was very encouraging, because it proved that magnetic particle seeds could serve as an effective implant for MDT systems, especially under conditions found in capillaries.