Preparation of Saccharide-Silica Composites by a Sol-Gel Method and the Application for Optical Resolution of Metal Chelate Compounds

A novel organic-inorganic composite was prepared by a sol-gel process using hydrolysis and condensation of tetraethoxysilane (TEOS) reacted with a saccharide. During the process, ethoxy groups of the TEOS were replaced with hydroxyl groups of the saccharide and, consequently, saccharide molecules were combined with silica through their hydroxyl groups. Samples obtained under different reaction conditions were used for optical resolution of a metal chelate compound. The resolution ability of the composites was affected by the amount of water added for hydrolysis and of the saccharide. In particular, the amount of water drastically influenced the optical resolution performance. Composites obtained at the lower H2O/TEOS ratio gave the metal chelate compound a higher optical rotation. Three types of composites with the same composition were prepared by kneading, impregnation and by the sol-gel method, and were compared. The sol-gel composite showed the best optical resolution ability. It was concluded that the optical resolution ability was closely related to dispersibility of saccharide in the silica matrix.     

Drying dissipative patterns of colloidal crystals of silica spheres in organic solvents

Drying dissipative structural patterns formed in the course of drying colloidal crystals of silica spheres (110 nm in diameter) in water, methyl alcohol, ethyl alcohol, 1-propyl alcohol, diethyl ether, and in the mixtures of ethyl alcohol with the other solvents above have been studied on a cover glass. The macroscopic broad rings were formed in the outside edges of the dried film for all the solvents examined. Furthermore, much distinct broad rings appeared in the inner area when the solvents were ethyl alcohol, methyl alcohol, and their mixtures. Profiles of the thickness of the dried films were sensitive to the organic solvents and explained well with changes in the surface tensions, boiling points, and viscosities of the solvents. The macroscopic and microscopic spoke-like crack patterns formed. The drying area (or the drying time) increased (or decreased) as the surface tension of the solvent decreased. However, the absolute values of these drying parameters are determined also by the boiling points of the solvents. Importance of the fundamental properties of the solvents is supported in addition to the characteristics of colloidal particles in the drying dissipative pattern formation.     

高效液相色谱氮杂冠醚键合固定相的合成及性能研究

我们曾用γ－氯丙基键合硅胶（ＣＰＳ），在氢化钠（ＮａＨ）作用下合成了３－（氮杂－１８－冠－６）丙基键合固定相（ＢＣＰ）［１］．该固定相对碱基、核苷酸、硝基苯酚等有较好的分离选择性，但由于ＮａＨ对硅胶基质腐蚀作用较大，导致ＢＣＰ柱效及渗透性较低．本文采...     

Hexagonal Ferrites from Melts and Aqueous Solutions,Magnetic Recording Materials

Owing to their particular crystallographic properties, ferrimagnetic hexagonal ferrites exhibit a far greater coercive force than the conventional magnetic pigments. They therefore appear to be suitable for use in magnetic information storage procedures, some of which are novel and are at the development stage. Thus, magnetic tapes of high coercive force containing barium ferrite could be used as master tapes for copying magnetic information or for producing forgery-proof magnetic cards, if magnetic heads having high-order write fields were successfully developed. Moreover, platelet-like ferrite pigments in which the preferred direction of magnetic orientation is perpendicular to the plane of the platelet are of great interest for perpendicular magnetic recording. In this progress report, the crystal structures, magnetic characteristics of hexagonal ferrites, and chemical processes for their production are discussed. In particular, reactions in salt melts or under hydrothermal conditions produce finely divided pigments whose particles have a pronounced hexagonal, plate-like habit, a narrow particle size distribution, and advantageous magnetic properties. The magnetic properties of the pigments crystallized from salt melts may be adjusted by cation exchange.     

Comparison of micro- and mesoporous inorganic materials in the uptake and release of the drug model fluorescein and its analogues

The uptake of the three species of the drug model fluorescein (fluorescein sodium salt (FNa), fluorescein free acid (F), and fluorescein diacetate (FDA)) by zeolite NaX and the mesoporous zeotype MCM-41 was investigated as well as their release rates into solutions at pH 7 and pH 4.5. UV/Vis analysis was carried out at a wavelength of 490 nm. Uptakes of the sodium salt of 9 % for zeolite X and 14 % for MCM suggest little penetration of the pores. The use of ethanol as the loading solvent for F resulted in little uptake for both zeolitic materials due to the successful competition of the ethanol for binding sites. Use of acetone (weaker proton acceptor) as loading solvent significantly improved the uptake of F to 17 % and 12 % for zeolite X and MCM, respectively, whilst the uptake of FDA in acetone increased still further to 22 % and 17 % for zeolite X and MCM, respectively. Generally there was a large initial release of the fluorescein analogues from the surface of the zeolites with very little further increase over time. The prescence of an esterase enzyme in the release medium of FDA tripled the release from MCM to 15 % but left the release from zeolite X unaffected at 6 %. The results obtained show that uptake of fluorescein and its analogues is dependent on the loading solvent used, the amount released is influenced by not only the solvent but the pH and the presence of enzymes in the release medium.     

Effect of Hydration–Dehydration Processes on the Structure and Porosity of Detemplated Silica Fibers

A study was carried out on the conditions of template removal (calcination or extraction by solvents) and hydration–dehydration processes on the hexagonal structure and porosity of detemplated fibers. The hydration–dehydration cycle leads to a decrease in fiber porosity, especially in fiber detemplation by extraction with surfactant solvents such as ethanol and acetic acid.     

沉淀二氧化硅消光剂的制备研究

涂料中的消光剂是一类能够改变涂膜表面光学性能的助剂。这类助剂能够在涂膜表面产生预期微粗糙度,使涂膜的光泽显著降低,给人一种古朴典雅的感觉。近几年来,我国的涂料工业方兴未艾,涂料总产量也跃居世界的前列。在这期间高光泽的亮光涂料以其色泽鲜艳、明亮等优点深受消费者的喜爱,并在相当长的时间内一统着涂料市场[1]。但是,随着人们生活水平的不断提高,一方面消费者感觉到了高光泽的亮光涂料成膜后反光比较严重,对人的眼睛有害;另一方面消费者的审美观念越来越倾向于休闲、时尚和个性化。这些因素就导致了人们对具有柔和外观的低光泽涂…     

An application of factorial design to the development of fused silica capillary columns

Stationary phase crosslinking conditions for fused silica capillary columns were optimized with the use of a factorial design experiment. This experimental strategy was chosen because it provided for the determination of two-factor interactions. A predictive model was developed for the desired chromatographic performance parameters as a function of the variables of the crosslinking reaction. Confirmatory experiments proved the usefulness of the mathematical model which resulted in the production of capillary columns of superior performance with significant improvements in reproducibility.     

Solid-phase extraction of iron(III) with an ion-imprinted functionalized silica gel sorbent prepared by a surface imprinting technique

A new Fe(III)-imprinted amino-functionalized silica gel sorbent was prepared by a surface imprinting technique for selective solid-phase extraction (SPE) of Fe(III) prior to its determination by inductively coupled plasma atomic emission spectrometry (ICP-AES). Compared with non-imprinted polymer particles, the ion-imprinted polymers (IIPs) had higher selectivity and adsorption capacity for Fe(III). The maximum static adsorption capacity of the ion-imprinted and non-imprinted sorbent for Fe(III) was 25.21 and 5.10 mg g⁻¹, respectively. The largest selectivity coefficient of the Fe(III)-imprinted sorbent for Fe(III) in the presence of Cr(III) was over 450. The relatively selective factor (α_r) values of Fe(III)/Cr(III) were 49.9 and 42.4, which were greater than 1. The distribution ratio (D) values of Fe(III)-imprinted polymers for Fe(III) were greatly larger than that for Cr(III). The detection limit (3σ) was 0.34 μg L⁻¹. The relative standard deviation of the method was 1.50% for eight replicate determinations. The method was validated by analyzing two certified reference materials (GBW 08301 and GBW 08303), the results obtained is in good agreement with standard values. The developed method was also successfully applied to the determination of trace iron in plants and water samples with satisfactory results.