Measurement of small-signal and large-signal responses of packaged laser modules at high temperature

In this paper, the pulsed injection method is extended to measure the chip temperature of various packaged laser modules, such as the DFB laser modules, the FP laser modules, and the EML laser modules. An optimal injection condition is obtained by investigating the dependence of the lasing wavelength on the width and period of the injection pulse in a relatively wide temperature range. The small-signal frequency responses and large-signal performances of packaged laser modules at different chip temperature are measured. The adiabatic small-signal modulation characteristics of packaged LD are first extracted. In the large-signal measurement, the effects of chip temperature, bias current and driving signal on the performances of the laser modules are discussed. It has been found that the large-signal performances of the EML modules depend on the different red-shift speeds of the DFB and EAM sections as chip temperature varying, and the optimal characteristics may be achieved at higher temperature.     

基于PIC方法的二维束流动力学模拟程序及其初步应用

为了深入研究强流负氢束在强流质子回旋加速器CYCIAE-100轴向注入线中的传输, 利用split-operator方法分解外场和束流自身的空间电荷场的作用. 对外 场利用单粒子跟踪技术, 采用一阶线性近似; 对空间电荷场采用PIC方法, 利用 快速傅里叶变换求解Poisson方程. 用FORTRAN95语言开发了一个基于面向对象技术的二维宏粒子传输计算程序CYCPIC2D, 本程序可以计算任意分布的强流束在输运线上的传输.最后给出了对CYCIAE-100注入线的模拟计算结果, 并和程序ORBIT, TRACE 3-D的结果进行比对验证, 结果表明: 空间电荷效应在此注入线上有较大的影响, 而且3个程序计算的不同中性化的结果基本上一致; 束流强度达到几十毫安时, 基于PIC方法的两个程序CYCPIC2D和ORBIT的计算结果完全吻合, 而线性近似程序TRACE 3-D有明显差异.     

The Morphology and Mechanical Properties of Isotactic Polypropylene Injection-Molded Samples with the Presence of β-Nucleation Agent and Periodical Shear Field

The pressure vibration injection molding (PVIM) method was used to prepare β-nucleated isotactic polypropylene samples (PVIM β-iPP samples); a relatively low, periodical shear was imposed on the polymer melt in the mold at the filling and packing stages. The crystal structures and crystal orientation of the PVIM β-iPP samples were investigated by polarizing light microscopy (PLM), scanning electron microscopy (SEM), and synchrotron two-dimensional wide-angle X-ray diffraction (2D-WAXD). The PLM observations indicated that a cylindrite layer, rather than the transition layer, was found in PVIM β-iPP samples, which is different from the conventional injection-molded (CIM) samples. In addition, the thickness of the oriented layer of the PVIM samples was obviously greater than that of the CIM samples. The SEM observations demonstrated that a large amount of shish-kebab structures appeared in the shear layer of the PVIM β-iPP samples; at the same time, numerous β-spherulites were formed in the core layer. The 2D-WAXD data indicated that orientation homogeneity, to some degree, could be obtained by the periodical shear during PVIM. As a result, the above-mentioned morphology of the PVIM β-iPP samples leads to potentially useful prominent reinforcement and toughening of the material.     

Electroluminescence enhancement in ultraviolet organic light‐emitting diode with graded hole‐injection and ‐transporting structure

Electroluminescent intensity and external quantum efficiency (EQE) in ultraviolet organic light‐emitting diodes (UV OLEDs) have been remarkably enhanced by using a graded hole‐injection and ‐transporting (HIT) structure of MoO₃/N,N ′‐bis(naphthalen‐1‐yl)‐N,N ′‐bis(phenyl)‐benzidine/MoO₃/4,4′‐bis(carbazol‐9‐yl)biphenyl (CBP). The graded‐HIT based UV OLED shows superior short‐wavelength emis‐ sion with spectral peak of ～410 nm, maximum electroluminescent intensity of 2.2 mW/cm² at 215 mA/cm² and an EQE of 0.72% at 5.5 mA/cm². Impedance spectroscopy is employed to clarify the enhanced hole‐injection and ‐transporting capacity of the graded‐HIT structure. Our results provide a simple and effective approach for constructing efficient UV OLEDs. (© 2015 WILEY‐VCH Verlag GmbH &Co. KGaA, Weinheim)     

衬底加热和电极修饰对提高有机场效应晶体管性能的影响

通过衬底加热和氧化钼(MoO3)修饰源漏极制备了并五苯有机场效应晶体管.研究了衬底温度和电极修饰层厚度对器件性能的影响.实验结果表明:当衬底温度为60℃、MoO3修饰层为10 nm时,器件性能获得了显著增强,场效应迁移率由原来的3.39×10-3 cm2/(V·s)提高到2.25 ×10-1 cm2/(V·s),阈值电压由12 V降低到3V.器件性能的改善归因于:衬底加热可以优化有源层形貌,改善载流子传输;而MoO3修饰层显著降低了电极与有源层之间的接触势垒,提高了载流子的注入.因此,衬底加热与电极修饰对于制备高性能有机场效应晶体管是不可或缺的优化手段.     

发光层位置对白光有机发光二极管的影响

同一种主体材料MADN中混掺不同的掺杂剂,分别制备了两种白光有机发光二极管,测试并研究了它们的发光效率、寿命、发光亮度、电致发光光谱以及色平衡度。结果表明,两种白光器件的性能受发光层的顺序和厚度的影响显著。发光层顺序由阳极到阴极方向为橙/蓝的器件的稳定性要优于发光层顺序为蓝/橙的器件,这是由于橙光发光层中的rubrene对空穴的陷进作用可捕获穿越橙光发光层中的空穴,从而有效地调控了器件内部的电子、空穴浓度的平衡。通过对器件的优化,制得了色坐标为(0.3201,0.3459)的接近标准白光的有机电致发光器件。     

全三维35 GHz双阳极磁控注入式电子枪数值模拟研究

基于trade-off平衡方程组得到35GHz双阳极磁控注入式电子枪的初始参数,通过编程对其主要参数进行优化设计,并经由自主研发的PIC粒子模拟软件CHIPIC中的电子枪计算模块对其进行全三维的数值模拟研究,最终获得了具有横纵速度比为1.5,最大速度零散约为5.4%的高性能电子枪,能够很好地满足35GHz-100kW回旋振荡管对电子束的要求。     

Cs2 CO3共蒸阴极对有机电致发光器件性能的影响

研究了碳酸铯(Cs2CO3)掺杂8-羟基喹啉铝(Alq3)作为电子注入层对有机电致发光器件性能的影响。结果表明,与常用的Cs2CO3超薄层作电子注入层相比,Cs2CO3∶Alq3共蒸阴极对器件效率和亮度有很大提高,器件电流效率从3.1 cd/A(Cs2CO31 nm/Al)提高到6.5 cd/A(Cs2CO33%∶Alq3/Al)。器件性能的提高归因于Cs2CO3∶Alq3共蒸阴极比单层Cs2CO3阴极具有更好的电子注入能力和电子传输性能。薄膜形貌表明,共蒸阴极能有效降低Alq3表面粗糙度,有助于提高器件发光性能及寿命。     

A bidirectional hybrid DWDM-PON employing optical injection locking technique and data comparators

A bidirectional hybrid dense-wavelength-division-multiplexing (DWDM)-passive optical network (PON) employing optical injection locking technique on vertical-cavity surface-emitting lasers (VCSELs) and data comparator, as well as optical injection locking technique on distributed feedback laser diodes (DFB LDs) and amplitude/phase compensator is proposed and demonstrated. Improved performances of bit error rate (BER) and carrier-to-noise ratio/composite second order/composite triple beat (CNR/CSO/CTB) were observed in our proposed bidirectional hybrid DWDM-PON. Bidirectional transmission in bidirectional hybrid DWDM-PON architecture is a very attractive option, the capacity of the optical network can be expanded relatively easily by bidirectional transmission technology.     

Expansion,injection and micro-explosion phenomena during the full combustion cycle of mixed fuel droplets of ethyl alcohol and biodiesel

In this study, mixed fuel droplets of ethyl alcohol and biodiesel with different volumes or ratios were prepared and the related expansion, injection and micro-explosion phenomena were investigated. During the tests, a mixed-fuel droplet was hung on a high-temperature-resistant Cr-Ni wire, which was transported to the preheating piston for heating and then was ignited automatically. Micro-needles and an infusion set also were employed to prepare mixed droplets with identical ratios but different volumes. Using a single-lens-reflex (SLR) camera, colour videos that captured the combustion process of the mixed droplets were taken and were processed into colour images using Adobe Premiere Pro CC. The colour image series were analysed to determine the ignition delay time, the burnout time and the flame characteristics during combustion of mixed droplets with different ratios. Instantaneous grey images were obtained by means of high-speed photography during combustion of the mixed droplets with different volumes and different ratios, and of droplets of E40 (in which the volume ratio of ethyl alcohol was 40%). Using Image pro plus and Origin software, the variation of normalised mean droplet diameter with time over the whole combustion cycle was calculated and the underlying reasons for various combustion phenomena were analysed.