Multifunctional Zn0.3Al0.4O4.5 crystals: An efficient photocatalyst for formaldehyde degradation and EBT adsorption

The Zn_0.3Al_0.4O_4.5 nanoparticles (ZnAlONPs) with size of 70–90 nm are used as an efficient photocatalyst for formaldehyde (HCHO) degradation and effective adsorbent for the removal of eriochrome black-T (EBT) dye from synthetic aqueous solution. Degradation of HCHO reactions were studied using TiO₂ (homemade), TiO₂ (P-25) and ZnAlONPs by irradiating under 18 W daylight lamp source for photocatalytic degradation. The HCHO degradation rate is about 67, 76 and 89% for TiO₂ (homemade), TiO₂ (P25) and ZnAlONPs during 2 h reaction, respectively at initial formaldehyde gas concentration of 20 ppm. Maximum adsorption capacity was optimized by changing the parameters such as pH, EBT concentration and adsorbent dosage. A  200 mg of ZnAlONPs are useable for quick removal of EBT (>95%). Langmuir isotherm model showed a maximum adsorption capacity of 90.90 mgg⁻¹. The ZnAlONPs could be successfully reused upto 5^th adsorption/desorption cycle for EBT dye removal from water samples.     

Salen–Mg-doped NH2–MIL-101(Cr) for effective CO2 adsorption under ambient conditions

A novel metal-doped metal–organic framework (MOF) was developed by incorporating salen–Mg into NH₂–MIL-101(Cr) structure under ambient conditions. The Schiff base complex was successfully prepared by condensing salicylaldehyde with a free amino group and then coordinating metal ions. Such a structure can endow the sample with higher CO₂ adsorption performance. At 0°C and 1 bar, the salen–Mg-modified sample achieves the maximum adsorption capacity of 2.18 mmol g⁻¹ for CO₂, which was 5.8% higher than the pristine salen–MOF under the same conditions. Notably, the Freundlich model indicates that the CO₂ adsorption process of all samples conforms to reversible adsorption. However, the correlation coefficients (R²) of the Mg-doped sample are lower than that of the pristine sample. Besides, the CO₂/N₂ adsorption selectivity and isosteric heat also show a similar trend. These results indicate that the salen–Mg can enhance the interaction between the material and CO₂ molecules.     

刚果红和结晶紫在锯末上的吸附性能研究

采用静态吸附法研究了刚果红和结晶紫在锯末上的吸附特性。结果表明,锯末是具有高脱色率的廉价吸附剂,最大脱色率可达96%。在pH4~10范围内,酸度对结晶紫的吸附影响较小,随着pH值增大,脱色率从96.6%缓慢降至91.1%。pH值对刚果红吸附影响较大,pH从4增大到7,脱色率迅速从22.5%增加至96.0%,然后,随pH值升高脱色率缓慢下降至91.4%。两种染料在锯末上的吸附等温线均较好的符合Freundlich方程,吸附动力学可以用拟二级动力学模型描述。计算了相应的吸附等温线参数和吸附动力学参数。     

绿茶对水溶液中Pb2+和Cd2+吸附性能初步研究

研究了绿茶对溶液中Pb2 和Cd2 离子的吸附和解吸性质。考察了pH、温度、吸附时间对绿茶吸附性能的影响,得到吸附动力学曲线和吸附等温线。结果表明,茶叶在pH为4~6的弱酸性范围内对两种金属离子的吸附效果最佳,在30℃时,茶叶对Pb2 和Cd2 的饱和吸附量分别为46.66 mg/g和33.29mg/g,吸附符合Langmuir吸附等温方程,并对吸附机理进行了初步的探讨。对解吸条件研究发现,用0.1 mol/L HCl和EDTA作为解吸剂,对Pb2 和Cd2 的解吸效果较好,解吸率达80%以上,可有效回收重金属Pb2 和Cd2 。     

Characterization and modeling of nonlinear hydrophobic interaction chromatographic systems

A general rate model was employed in concert with a preferential interaction quadratic adsorption isotherm for the characterization of HIC resins and the prediction of solute behavior in these separation systems. The results indicate that both pore and surface diffusion play an important role in protein transport in HIC resins. The simulated and experimental solute profiles were compared for two model proteins, lysozyme and lectin, for both displacement and gradient modes of chromatography. Our results indicate that a modeling approach using the generate rate model and preferential interaction isotherm can accurately predict the shock layer response in both gradient and displacement chromatography in HIC systems. While pore and surface diffusion played a major role and were limiting steps for proteins, surface diffusion was seen to play less of a role for the displacer. The results demonstrate that this modeling approach can be employed to describe the behavior of these non-linear HIC systems, which may have implications for the development of more efficient preparative HIC separations.     

Study on the Binding Characteristic of Methamidophos‐Specific Molecularly Imprinted Polymer and the Interactions between Template and Monomers

A new molecularly imprinted polymer (MIP) was prepared using methamidophos (MAP) as the template molecule based on non‐covalent interaction. The complexes formed between template and monomers before polymerization were characterized by ¹H NMR titration test, FT‐IR and UV spectrometry study. These studies indicated that a 1:2 molecular complex formed dominantly between MAP and functional monomers. A model mainly involving cooperative hydrogen interaction was proposed by exact placement of functional groups. Association constant was estimated to be 2.894 × 10⁶ L²/mol². When the initial concentration of MAP was 1.0 mmol L^?1, the affinity capacity of MIP was 4.23 times that of NIP. The binding performance of MIP was modeled with the Freundlich isotherm (FI) and the total number of binding sites was calculated to be 33.97 μmol/g. The MIP showed great homogeneity with a heterogeneity index of m = 0.7356. The specificity of MIP was investigated by single‐analyte binding and molecularly imprinted solid‐phase extraction (MISPE) assays using MAP and other structurally related organophorous pesticides (OPPs). The results indicated that the MIP had a marked preference for MAP.     

Synthesis of caffeic acid molecularly imprinted polymer microspheres and high-performance liquid chromatography evaluation of their sorption properties

In the current work, a molecularly imprinted polymer (MIP) has been synthesised and used to enable the extraction of a naturally-occurring antioxidant from complex media. More specifically, we describe the first example of a caffeic acid (CA) MIP which has been synthesised in the form of well-defined polymer microspheres, and its use for the extraction of CA from fruit juice sample. The CA MIP was synthesised by precipitation polymerisation using 4-vinylpyridine as functional monomer, divinylbenzene-80 as crosslinker and acetonitrile:toluene (75/25, v/v) as porogen. The particle sizing and morphological characterisation of the polymers was carried out by means of scanning electron microscopy (narrow particle size distribution; ～5 and 1.5 μm particle diameters for the MIP and NIP [non-imprinted polymer], respectively) and nitrogen sorption porosimetry (specific surface areas of 340 and 350 m(2)g(-1), and specific pore volumes of 0.17 and 0.19 cm(3)g(-1) for the MIP and NIP, respectively). The polymers were evaluated further by batch rebinding experiments, and from the derived isotherms their binding capacity and binding strength were determined (number of binding sites (N(K))=0.6 and 0.3 mmol g(-1) for the MIP and NIP, respectively, and apparent average adsorption constant (K(N))=10.0 and 1.6L mmol(-1) for the MIP and NIP, respectively). To evaluate the molecular recognition character of the MIP it was packed into a stainless steel column (50 mm × 4.6 mm i.d.) and evaluated as an HPLC-stationary phase. The mobile phase composition, flow rate, and the elution profile were then optimised in order to improve the peak shape without negatively affecting the imprinting factor (IF). Very interesting, promising properties were revealed. The imprinting factor (IF) under the optimised conditions was 11.9. Finally, when the imprinted LC column was used for the selective recognition of CA over eight related compounds, very good selectivity was obtained. This outcome enabled the direct extraction of CA in commercial apple juice samples with recoveries in excess of 81% and, rather significantly, without any need for a clean-up step prior to the extraction.     

两种形貌的介孔SiO2对纤维素内切酶吸附性能的研究

以EDTA2-、SO42-作为反离子分别合成了具有管状和圆盘状结构的介孔SiO2,并测定了2种介孔SiO2焙烧至不同温度时的表面积、孔体积参数,及其等电点;通过752分光光度计在550nm处测定纤维素内切酶的吸光度,研究了2种形貌的介孔SiO2对纤维素内切酶的吸附性能,同时测定了固定酶的活性。结果表明,管状和圆盘状结构的介孔SiO2对纤维素内切酶的吸附等温线分别为Ⅱ和Ⅰ型;介孔SiO2焙烧至700℃时,两者皆为Ⅱ型;至850℃时,前者转化为Ⅰ型,而后者转化为Ⅴ型。吸附等温线类型与介孔SiO2的结构、等电点以及酶分子尺寸与介孔尺寸的相匹配有关。酶经过介孔SiO2吸附固定后,稳定性明显提高;其中,管状结构的介孔SiO2对酶具有最大的负载量,但固定酶的活性却较低。     

Intrinsic Flexibility of the Zeolitic Imidazolate Framework ZIF‐7 Unveiled by CO2 Adsorption and Hg Intrusion

ZIF‐7, built as an assembly of Zn^II centers and benzimidazolate ligands, shows prominent S‐shaped isotherms upon CO₂ adsorption that can be attributed to sorbate‐induced gate‐opening phenomena involving a narrow‐to‐large pore phase transition. This peculiar sorption pattern can be captured via the formulation of thermodynamic isotherms, providing a direct enthalpic and entropic view of the gate‐opening process. Relying on such an approach, an energy barrier with preferential enthalpic nature for CO₂ adsorption/desorption in the gate‐opening region could be unveiled. Moreover, the elastic energy involved during the gate‐opening process was revisited to 1.4–2.8 kJ mol^?1 of solid in the temperature range 273–323 K, matching the value measured by isostatic compression of a ZIF‐7_lp sample filled with DMF and showing a dominant entropic contribution.