流动注射-结晶紫-磷钼杂多酸离子缔合体系光度法测定水中痕量正磷酸盐

在一定的酸度条件下,结晶紫与磷钼杂多酸离子缔合物的流动注射分光光度法可直接测定痕量磷.灵敏度高,重现性和选择性好.水中常见离子不干扰痕量磷的测定,工作曲线的线性范围为0～500μg·L~(-1)的磷,检出下限达1.0μg·L~(-1),以120h~(-1)采样频率,对各种天然水样进行测定,回收率为92.5%～105.0%,相对标准偏差为0.1%～6.7%.     

Influence of operational parameters on retention of ultra-high molecular weight polystyrenes in thermal field-flow fractionation

Summary The influence of various parameters (concentration of the injected polymer solution, flow rate, temperature gradient, relaxation conditions) on the retention and shape of the fractogram of ultra-high molecular weight polystyrenes in thermal field-flow fractionation was investigated. Under the operating conditions adopted, reproducible oscillations in the peak shape are observed for molecular weights larger than a few millions, especially at relatively high polymer concentration. They are attributed to some hydrodynamic instabilities. The retention of ultra-high molecular weight polystyrenes at high flow rate is strongly dependent on the initial relaxation period. All of the investigated operational variables have a complex effect on the resulting shape of the fractogram. Consequently, the confirmation of the shear-induced focusing of macromolecules across the channel thickness requires further study. Experiments on reinjection of fractions collected after an initial high speed pass through the separation system leads to the conclusion that shear degradation of the ultra-high molecular weight polymers did not occur under the investigated experimental conditions even at the highest flow rates.     

Continuous flow and flow injection stripping voltammetric determination of silver(I), mercury(II), and bismuth(III) at a bulk modified graphite tube electrode

The epoxy-impregnated graphite tube electrode bulk modified with 2-mercaptobenzoxazole, employed in a wall-jet configuration, was found to be useful for the continuous flow and flow injection stripping voltammetric determinations of Ag^I, Hg^II and Bi^III. For continuous flow, detection limits for Ag^I, Hg^II and Bi^III were 1.8 × 10⁻¹⁰ M, 1.9 × 10⁻⁹ M and 9.5 × 10⁻⁹ M, respectively (10 min accumulation, S/N = 3). Precisions for 5.00 × 10⁻⁹ M Ag^I, 1.00 × 10⁻⁸ M Hg^II and 1.00 × 10⁻⁷ M Bi^III were 10.5%, 5.77 % and 7.90% (relative standard deviations, n = 6), respectively. In the case of flow injection stripping, with a 500 μL injection loop, detection limits of 0.59 ng, 2.0 ng and 120 ng were obtained for Ag^I, Hg^II and Bi^III, respectively (S/N = 3). Selected metal ions, inorganic and organic substances were investigated for interferences. The electrode was tested with a certified sample and then applied to the determinations of the metal ions in a urine and a sea-water sample.     

Selective flow-injection determination of methanol in the presence of ethanol based on a multi-enzyme system with chemiluminescence detection

A highly selective flow-injection system was developed for the determination of methanol. The system consisted of three immobilized enzymes with luminol chemiluminescence detection. First, methanol was oxidized in the presence of alcohol oxidase to yield formaldehyde and hydrogen peroxide. The hydrogen peroxide produced was then destroyed by catalase. The formaldehyde formed in the first stage was further oxidized by NAD⁺-formaldehyde dehydrogenase. The NADH formed was oxidized by 1-methoxy-5-methylphenazinium methylsulphate (1-MPMS), and finally the reduced 1-MPMS was spontaneously oxidized and hydrogen peroxide was produced. The concentration of the hydrogen peroxide produced, which was proportional to the initial concentration of methanol, was determined by luminol chemiluminescence. The determination range was from 0.1 to 100 mg l⁻¹ and the response time was less than 2 min per sample with a relative standard deviation of less than 3%. The system showed good selectivity for methanol; the response was ca. 50 times higher than for ethanol.     

流动注射在线共沉淀HG-AFS测定痕量铅

建立了流动注射在线共沉淀HG-AFS测定痕量铅的分析方法。方法基于铅在碱性介质中与氢氧化镁共沉淀，沉淀收集在锥形沉淀腔中，用HCl溶洗沉淀和NaBH4反应，产生的氢化物被载气引入原子化器中进行测定。测定铅的RSD为3％(5ng/mL，n=10)，检出限为0．01ng。检出限较直接进样降低了11倍。对国家标准物质中铅的测定结果与标准值相符。     

流动注射-速差动力学分析研究 meso-四-(4-三甲铵基苯)卟啉光度法测定痕量铅

本文研究了多种金属离子与meso-四-(4-三甲铵基苯)卟啉的显色反应动力学特性。利用Pb(Ⅱ)和其它金属离子之间的反应速差,建立了一种选择性好的测定痕量Pb(Ⅱ)的流动注射分析法。将此法应用于陶瓷和人发样品中铅的直接测定,结果满意。     

停留—催化反应速差动力学法同时测定Fe,Mo

根据Ｆｅ（Ⅲ）、Ｍｏ（Ⅵ）对Ｈ２Ｏ２氧化邻氨基酚的催化反应速率不同，结合流动注射停留技术，建立了同时测定Ｆｅ（Ⅲ）、Ｍｏ（Ⅵ）的速差动力学分光光度法．测定铁和钼的线性范围分别为０．１～２．５μｇ／ｍＬ和０．５～１５μｇ／ｍＬ．除Ｗ（Ⅵ）的允许量较小外，其它离子不干扰测定．用本法测定了合成样液中铁和钼含量，结果满意．     

二乙基二硫代氨甲酸银体系流动注射法测定砷

本文设计了一种ＡｇＤＤＣ流动注射－分光光度法测定砷的系统。该系统采用自制的氢化物发生及吸装置，将液体流路和载气流路结合在一起。     

流动注射分光光度法测定水体总磷

提出了一种单通道紫外消解流动注射比色分析法，能快速测定水样中总磷。实验采用了微量恒流混合泵、新型的细长型高灵敏度流通池及紫外消解器、液流分配阀、恒流瓶等FIA装置，并使用工业编程控制器和智能触摸屏进行控制和计算，使操作更为方便。此法分析时间短，测量范围宽，精度高，适合于各种水体的测定。     

A flow injection-ETAAS system for the on-line determination of total and dissolved silica in waters

In this work total (Si-tot) and ‘soluble’ or reactive (Si-sol) concentrations of silicon in natural and tap waters were sequentially determined by electrothermal atomic absorption spectrometry (ETAAS). First, samples were on-line diluted based on the merging-zone principle in order to allow the determination of Si-tot within the 300–1000 μgSi l⁻¹ range. After the dilution process, a sub-sample was collected in the capillary of a sampling arm assembly (SAA). Thereafter, samples were subject to a precipitation/dissolution process in order to allow the determination of Si-sol within the 280–850 μgSi l⁻¹. Si-sol was precipitated with ammonium chloride and collected on the walls of a knotted coil. The precipitate was dissolved with ammonium molybdate in an acidic medium (HNO₃) and a sub-sample was then collected in the SAA. In both cases, 10 μl volumes of the sub-sample were injected into the atomizer with the previous introduction of 20 ng of Eu as chemical modifier (10 μl) by the spectrometer autosampler. The recovery values obtained with natural waters spiked samples were over 46% and the agreement between observed and certified samples values was good. The proportion of Si-sol in comparison with the Si-tot was high (85–95%) in most natural waters. The precision of the method was 2.4–3.5 and 4.5–6.2% (n=10) for the determination of Si-tot and Si-sol, respectively.